How to Use the Electronic Parking Brake on Honda Vezel?

1 Answers
CaydenMarie
07/30/25 7:32am
The method to use the electronic parking brake on Honda Vezel is simply to lift or press the paddle. Relevant details are as follows: 1. The Honda Vezel is a compact SUV with body dimensions of 4328mm in length, 1772mm in width, and 1605mm in height, with a wheelbase of 2610mm. 2. The 2020 Honda Vezel is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 96kW and a maximum torque of 155Nm, paired with a 6-speed manual transmission. It features a MacPherson strut front suspension and a torsion beam rear suspension.
Was this review help?
13
5
Share
More Forum Discussions

What is the Principle of Wheel Alignment?

Wheel alignment is used to measure the distance that the wheels rotate forward or deviate from the vehicle's centerline. Here is the relevant information: 1. Camber: Camber is the angle of the tire relative to the vertical reference line. When the top of a wheel tilts outward, it is said to have positive camber. When the top of a wheel tilts inward, it is said to have negative camber. The camber setting can affect vehicle steering control and tire wear. 2. Caster: Caster is the angle of the steering axis tilting forward or backward. Caster is measured by observing the angle between the steering axis and the vertical line from the side view. 3. Toe: The function of toe is to compensate for the tendency of the tires to roll inward or outward due to camber and road resistance, ensuring the vehicle's straight-line stability.
4
0
Share

Where is the Mazda 3 Air Filter Located?

The air filter for the Mazda 3 is located inside the center console near the left leg of the front passenger seat. Below are the specific steps to replace the air filter: 1. First, release the two plastic clips under the glove compartment of the front passenger seat, then remove the lower panel (be sure to disconnect the lighting control wire connector inside). 2. Insert your fingers into the gap of the plastic panel near the left leg of the front passenger seat and pull outward firmly to slightly remove the panel. 3. Once the panel is slightly removed, release the two plastic clips inside, then slide the plastic panel toward the rear of the vehicle to detach it. 4. After removing the plastic panel, you will see the Mazda 3 air filter housing. Unscrew the bolt on the housing to open it, revealing the air filter inside. 5. Replace the old air filter with a new one, then reassemble the panel in the reverse order of disassembly. The entire process of replacing the Mazda 3 air filter is now complete.
15
0
Share

What are the test contents for upgrading from C1 to B1 driver's license?

C1 driver's license holders who wish to upgrade to a B1 license need to take three test subjects, which are: Subject 1 (Road traffic safety laws, regulations, and related knowledge test); Subject 2 (Field driving skills test); Subject 3 (Road driving skills test and safe civilized driving common sense test). C1 driver's license: The C1 driver's license is one of the motor vehicle driver's license codes. The scope of vehicles allowed to be driven with a C1 license includes small and micro passenger vehicles, light and micro cargo vehicles; light, small, and micro special-purpose vehicles; and small passenger vehicles with a seating capacity of 9 or fewer people. Application age: The minimum age limit for a C1 driver's license is 18 years old, with no upper age limit. However, applicants aged 70 and above must pass tests on memory, judgment ability, and reaction ability.
3
4
Share

How to Use Lights When Entering a Ramp?

When entering a ramp, you should turn on the right turn signal in advance and make sure it is safe before driving into the ramp. Here is some additional information: 1. At night, visibility is reduced. In addition to turning on the right turn signal in advance, you should also turn on the position lights and alternate between high and low beams. 2. When driving on the road, using lights correctly can improve safety during the journey. 3. When driving on urban roads, do not turn on the high beams, as this will affect the vision of oncoming drivers and the drivers ahead. 4. When driving on rural roads or highways without streetlights, turn on the high beams. However, as a courtesy, turn them off when meeting another vehicle. 5. In a car's lighting system, brake lights and turn signals are actually more prone to malfunctions. It is recommended to regularly check the working condition of the brake lights and turn signals.
5
3
Share

How to Adjust the Mazda 3 Axela Seat?

Here are the methods for adjusting the Mazda 3 Axela seat: 1. Mazda 3 Axela Front Seat Adjustment (Power Seat): (1) Press the lumbar support button to adjust the angle of the lumbar support. (2) Move the switch forward or backward to control the seat's forward or backward movement. Lift or press down to adjust the seat height. (3) Move the backrest switch forward or backward to adjust the backrest angle. 2. Mazda 3 Axela Front Seat Adjustment (Manual Seat): (1) Pull the backrest switch and use your waist strength to adjust the backrest to the desired position, then release the switch. (2) Height adjustment switch: This switch controls the seat height—pull up to raise and press down to lower. (3) Front and rear position adjustment: The lever is located under the seat; pull it to adjust the seat position.
3
4
Share

Where to Add Urea for Vehicles?

Vehicle urea solution comes with a filling tube, which is used to fill the urea solution into the vehicle's urea tank. Additional information: 1. Vehicle urea solution: Vehicle urea is an essential product for heavy-duty diesel vehicles to meet the National IV emission standards. Vehicle urea refers to a urea aqueous solution with a urea concentration of 32.5% and a solvent of ultra-pure water, with raw materials being urea crystals and ultra-pure water. For heavy-duty trucks, buses, and other diesel vehicles to meet the National IV emission standards, an appropriate SCR system must be selected for exhaust treatment, and this system must use urea solution to treat nitrogen oxides in the exhaust. Therefore, vehicle urea solution has become an essential product for heavy-duty trucks and buses to meet the National IV emission standards. 2. Suggestions for choosing vehicle urea: (1) Comply with GB29518-2013. (2) Have the AdBlue certification issued by the German Automotive Industry Association. (3) Have the CGT certification issued by the China Internal Combustion Engine Industry Association.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.