How to use the electronic gear shift of Audi A4L?

1 Answers
LeEli
07/28/25 5:45pm
Here is the introduction of the gear positions for the electronic gear shift of Audi A4L: 1. The left side of the "D/S" position is the automatic forward gear, and the right side is the manual forward gear: if you use the manual mode, you need to manually shift gears. 2. The "N" gear is the neutral gear: if the vehicle needs to be parked for a short time or needs to be towed due to a malfunction, you can shift the gear to the "N" position. 3. The "R" gear is the reverse gear: used when reversing. 4. The "P" gear is the parking gear: when parking, you need to shift the gear to the "P" position, and for long-term parking, you also need to pull up the handbrake. The button with "(P)" is the electronic parking brake button. 5. The button with the "A" symbol in the lower right corner is the auto start-stop button: when the auto start-stop function is turned on, the engine will automatically shut off during temporary stops, which helps save fuel and reduce exhaust pollution.
Was this review help?
9
5
Share
More Forum Discussions

What does DC/DC mean on a car?

DC/DC converter is a current conversion device used in new energy vehicles. Here is more relevant information: 1. Types of DC/DC converters: DC/DC converters are divided into three categories: boost DC/DC converters, buck DC/DC converters, and buck-boost DC/DC converters. The appropriate control type can be selected based on requirements. 2. Composition of DC/DC converters: A DC-DC converter generally consists of a control chip, inductor coil, diode, transistor, and capacitor. When evaluating the performance of a DC-DC converter, the quality cannot be judged solely based on the control chip. The characteristics of the peripheral circuit components and the wiring method of the substrate can affect the performance of the power circuit, so a comprehensive evaluation should be made.
13
3
Share

Should You Lift the Accelerator Before Pressing It Again for Automatic Transmission Acceleration?

For accelerating with an automatic transmission, it is recommended to slightly release the accelerator (the automatic transmission will issue an upshift command) before pressing it again. This ensures smooth gear shifting, allowing for sequential upshifts and speed increases. Below are specific tips for driving an automatic transmission vehicle: 1. Driving on Flat Roads: When driving on flat roads, gently lifting the accelerator pedal will prompt the transmission to upshift automatically. For overtaking, release the accelerator slightly before pressing it down firmly to achieve maximum effect. This is because the sudden acceleration required for overtaking cannot be achieved solely by the transmission's capability. 2. Avoid Coasting in Neutral: Do not coast in neutral, such as shifting the automatic transmission lever into neutral before a red light or when going downhill. This can damage the automatic transmission vehicle. The gears in the automatic transmission will rotate at high speeds driven by the wheels, reaching up to 3000 RPM momentarily. Due to insufficient oil supply from the transmission oil pump, the gears may not receive adequate lubrication, leading to overheating and wear, which can raise the transmission oil temperature and shorten its lifespan.
20
5
Share

How to Check the Remaining Fuel in the Tank?

Both analog and digital fuel gauges require the vehicle to be started before readings can be taken. The analog fuel gauge is marked with two letters, E and F. E stands for Empty, indicating the tank is empty, while F stands for Full, indicating the tank is full. The closer the needle is to the letter F, the more fuel remains; the closer it is to the letter E, the less fuel remains. When the fuel icon lights up, it indicates that the remaining fuel is low and refueling is needed as soon as possible. Below are some additional details: 1. The fuel gauge only provides a rough estimate of the fuel level and cannot display the exact remaining amount, serving merely as a reference for the driver. For example, a digital fuel gauge might show a remaining range of 300 kilometers, but in reality, due to factors like road conditions and vehicle status, the actual range might only be 150 kilometers. 2. The fuel system mainly consists of four parts: the fuel gauge, sensor circuit, variable resistor, and float. When the tank is full, the resistance value of the variable resistor connected to the float decreases, causing the circuit current to reach its maximum. At this point, the fuel gauge needle is at its highest position. As the fuel level drops, the resistance value of the variable resistor increases, reducing the circuit current and causing the fuel gauge needle to lower accordingly.
9
0
Share

Do I Need to Press the Clutch and Brake When Starting the Engine in Subject Two?

When starting the engine in Subject Two, you do not need to press the clutch, and starting with the clutch pressed will not result in point deduction. However, you must press the brake when igniting. Below is relevant information about Subject Two: 1. Introduction to Subject Two: Subject Two, also known as the small road test, is part of the motor vehicle driver's license examination. It is the abbreviation for the field driving skills test. For small vehicles (C1 and C2), the test items include five mandatory components: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving through curves. 2. Subject Two Retake Rules: If you fail the Subject Two test on the first attempt, you are allowed one retake. If you do not take the retake or fail the retake, the current test session ends, and the applicant must reschedule the test after ten days. Within the validity period of the driving skills test permit, the number of test reschedules for Subject Two and Subject Three (road driving skills test) must not exceed five. If the fifth test attempt is still unsuccessful, the results of other subjects that have already been passed will be invalidated.
10
0
Share

What Causes an Automatic Transmission Car to Stall Automatically?

Automatic transmission cars generally do not stall easily. The reasons for stalling are as follows: 1. Use of inferior fuel: Prolonged use of low-quality fuel can lead to excessive carbon buildup in the engine, making the vehicle highly prone to stalling. 2. Poor fuel flow: Blocked fuel lines are also a significant cause of cars stalling midway. One reason for poor fuel flow is the use of substandard fuel with too many impurities, leading to clogged fuel lines and inadequate fuel supply. 3. Insufficient driving skills: Lack of driving proficiency is another factor that cannot be overlooked when it comes to car stalling. 4. Electrical circuit failure: During driving, a low-voltage power outage can cause the car to stall.
15
3
Share

What Are the Five Major Functions of Transmission Fluid?

Here are the five major functions of transmission fluid: 1. Cleaning effect: Keeps the shifting system clean. 2. Extending lifespan: Prolongs the service life of internal transmission components. 3. Low-temperature resistance: Provides effective lubrication even in cold conditions. 4. Reducing fluid loss: Minimizes fluid loss under harsh operating conditions. 5. Lubrication: Ensures the normal operation of the transmission. Note: Under normal driving conditions, automatic transmission fluid should typically be replaced every 120,000 kilometers, and every 60,000 kilometers under severe driving conditions.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.