How to Use the Cruise Control in the 2021 Toyota Corolla?

How Many Types of Transmission Fluid Are There?

Transmission fluid is a mechanical or hydraulic device used for mechanical power conversion. Here is an introduction to how many types of transmission fluid there are: 1. Introduction: In automobiles, the transmission is commonly referred to as the "gearbox"; in industrial machinery, it is often called a "speed changer," which is a mechanical or hydraulic device for mechanical power conversion. 2. Performance in Use: Currently, the better method for changing transmission fluid is dynamic fluid replacement. This involves using specialized transmission cleaning equipment to fully circulate the old fluid during transmission operation, thoroughly draining it before adding new transmission fluid. This method achieves a fluid replacement rate of over 90%, ensuring excellent results.

17

1

Share

How to Power On the Car with One-Key Start?

With the smart key inside the car, pressing the one-key start button will power on the vehicle. Here is some related information about one-key start: 1. Definition: The one-key start device is part of a smart car, serving as a button mechanism to simplify the starting process and also to turn off the engine. This device can be retrofitted either at the original key lock position or as an independent panel. 2. Precautions: The starting method is software-based one-key start. There are three main points to note when installing a one-key start system (the wiring of the plug under the ignition switch, the position of the button, and the handling of the steering lock), and it comes with multiple functions.

7

1

Share

What is the Function of a Knock Sensor?

The functions of a knock sensor are: 1. To measure engine vibration and adjust the ignition timing when engine knocking occurs; 2. It serves as an AC signal generator to detect the speed and position of the rotating shaft. A knock sensor consists of: a magnetic core, permanent magnet, and induction coil. The working principle of a knock sensor is: when vibration or knocking occurs, it generates a voltage peak. The greater the knocking or vibration, the higher the peak voltage produced by the knock sensor. A certain high frequency indicates knocking or vibration. The knock sensor can measure frequencies in the range of 5 to 15 kHz. When the control unit receives these frequencies, the computer recalibrates the ignition timing to prevent further knocking.

17

4

Share

Consequences of a Stuck Turbo Wastegate?

About the consequences of a stuck turbo wastegate, the introduction is as follows: 1. Engine performance. The engine exhibits sluggish response to throttle input at low to medium speeds, and knocking may occur during medium to high-speed acceleration, affecting the engine's power output. If diagnosed with a specialized diagnostic tool, the engine system will display fault codes indicating issues with the turbocharging system. 2. Symptoms of wastegate damage. This can lead to boost pressure leakage, reducing the compressor's efficiency, resulting in engine power loss, difficulty accelerating, or black smoke emissions. 3. Basic function of the wastegate. When the engine's intake pressure exceeds a certain threshold, the mechanism acts on the turbine side to divert exhaust gases, thereby reducing the exhaust flow through the turbine.

8

1

Share

Can Car Batteries Really Be Repaired?

Car batteries can be repaired. For sulfated or discharged batteries, use a battery repair device for restoration. For batteries with broken grids or short circuits, manually open the casing and replace the plates, but remember to add battery replenishment fluid before repairing. Battery repair methods: 1. Charger repair - When a car battery is discharged, promptly use a charger to recharge it; 2. Jumper cable repair - A discharged car battery can also be recharged using jumper cables; 3. Repair device restoration - If a regular charger fails to recharge the battery, it might be due to insufficient voltage. In this case, use a repair device's high-resistance mode to boost the voltage above 10V for successful charging. If the battery voltage remains below 10V even after charging and repair attempts, replace the electrolyte before recharging.

2

1

Share

What does emergency lane keeping activation mean?

Emergency lane keeping activation means that the emergency lane keeping system has been activated. The emergency lane keeping system can detect emergency situations and remind the driver to correct the driving route. The following are the methods to turn on or off the emergency lane keeping system, as well as an introduction to how the emergency lane keeping system works: Methods to turn on or off the emergency lane keeping system: In the car's central control screen, open the lane assist system and select emergency lane keeping to turn this function on or off. How the emergency lane keeping system works: It uses the onboard camera in conjunction with the processor to identify lane lines. Once the vehicle crosses the lane line without the turn signal activated, the system will determine that the vehicle is in an abnormal driving state. The system will then warn the driver by vibrating the steering wheel, reminding the driver to steer the vehicle back into the original lane.

9

0

Share

How to Use the Cruise Control in the 2021 Toyota Corolla?

How Many Types of Transmission Fluid Are There?

How to Power On the Car with One-Key Start?

What is the Function of a Knock Sensor?

Consequences of a Stuck Turbo Wastegate?

Can Car Batteries Really Be Repaired?

What does emergency lane keeping activation mean?

How to cancel the SOS malfunction in a Mercedes-Benz?

How to Turn Off a BMW with One-Button Start?

What Causes the Engine Warning Light to Illuminate and Lack of Power When Accelerating?

How to Remove New Car Odor?