How to use the cigarette lighter in the Mazda3 Axela?

1 Answers
DiMackenzie
07/29/25 8:36pm
The method to use the cigarette lighter in the Mazda3 Axela: The cigarette lighter socket is located in the storage compartment in front of the gear lever. Simply press down the handle of the cigarette lighter to start heating, and it will automatically pop out when ready. The cigarette lighter is a standard component in all cars, designed to provide a convenient ignition source for smokers. The cigarette lighter typically operates on 12V DC power, with the central elastic head serving as the positive terminal and the side clips as the negative terminals. It is directly connected to the car's battery, sharing the same current and power specifications. The Mazda3 Axela is a vehicle produced by Changan Mazda, with dimensions of 4582mm in length, 1795mm in width, and 1458mm in height, and a wheelbase of 2700mm.
Was this review help?
3
2
Share
More Forum Discussions

Is Fuel Additive Really Effective? How to Use It?

The effectiveness of fuel additive becomes more noticeable as the vehicle ages: 1. For new cars: It is unnecessary to add fuel additive. Since new cars have minimal carbon deposits and very little engine wear, which is almost negligible, adding fuel additive at this stage would be ineffective and only increase the cost of vehicle maintenance. 2. For older cars: When there is a significant amount of carbon deposits, fuel additive is needed to clean them. Generally, fuel additive should be used for vehicles with a mileage of over 50,000 kilometers, and it should be added every six months or every 5,000 km.
20
4
Share

How to Operate a Manual Transmission Car with Push-Button Start

The operation method for a manual transmission car with push-button start is as follows: 1. Before getting in the car, observe the surroundings to ensure safety, then get in, sit properly, and fasten the seatbelt. 2. Press the brake pedal with your right foot and use your right index finger to press the 'Push-Button Start' key, ensuring the gear is in the P position from the previous parking. At this point, the car's engine will start and run. 3. Next, shift to D gear or R gear. Use R gear when reversing is needed, and D gear when moving forward without reversing. 4. Release the handbrake, keeping your right foot on the brake pedal until this step. 5. If you need to move forward and have already shifted to D gear, move your right foot to the accelerator pedal and gently press to move forward. 6. If you need to reverse, gently lift your right foot to release the brake, but keep it ready on the brake pedal to control the reversing speed effectively. Once you've reversed to the desired position, press the brake firmly, shift to D gear, move your right foot to the accelerator, and gently press to move forward.
19
3
Share

Can a car that uses 98 octane fuel switch to 95 octane? What are the differences?

It is possible for a car that uses 98 octane fuel to switch to 95 octane, but this should only be done in emergencies and not for prolonged mixed use. The differences between 95 octane and 98 octane fuel are as follows: Difference 1: Different iso-octane values. 98 octane gasoline contains 98% iso-octane, while 95 octane gasoline contains 95% iso-octane. Difference 2: Different additive components. 98 octane gasoline is a mixture containing 98% octane and 2% n-heptane, while 95 octane gasoline contains 95% iso-octane and 3% n-heptane. Difference 3: Different characteristics. The advantages of 98 octane gasoline are "two highs and two lows"—higher anti-knock performance and power output, and lower harmful substances and exhaust pollution. For 95 octane gasoline, high-compression engines should use high-octane fuel; using low-octane fuel in high-compression engines can cause abnormal combustion, leading to knocking, increased fuel consumption, and reduced driving power. Difference 4: Different prices. 98 octane gasoline is more expensive than 95 octane gasoline. Difference 5: The state has strict standards for automotive gasoline. It requires gasoline to have a certain octane rating (commonly known as the gasoline grade), and there are strict regulations on the content of various chemical components in gasoline.
10
3
Share

How often should the transmission fluid be changed for a BMW X3?

BMW X3 transmission fluid should be changed every 80,000 kilometers. Below are the methods for changing the transmission fluid and the precautions to take: Methods for changing the transmission fluid: There are two methods: one is gravity replacement, and the other is machine circulation replacement. Machine circulation replacement is recommended because it can clean the transmission, whereas gravity replacement only changes the fluid without cleaning the transmission. Precautions for changing the transmission fluid: When changing the transmission fluid, it is essential to use the same type of fluid as originally specified for the vehicle. Whether to change the transmission fluid should be judged based on the transmission's operating condition. If the vehicle shifts smoothly and there is no significant change in transmission noise, changing the fluid may not be necessary.
12
2
Share

What brand is the Cadillac audio system?

Cadillac's audio system is from the BOSE brand. The role of car audio systems: Car audio systems are radio devices installed to alleviate the monotony of travel for drivers and passengers. Today's car audio systems have reached high standards in sound quality, operation, and vibration resistance, capable of handling the bumps of rough roads while ensuring stable performance and perfect sound quality. Introduction to BOSE audio: BOSE is the largest speaker manufacturer in the United States, headquartered in Massachusetts, with hundreds of engineers dedicated to research and development. It is a wholly independent company. The products also excel in the fields of car audio and aerospace technology. In addition to consumer products, Bose has extensive developments in professional audio. Bose professional audio systems have been successfully applied in large sports venues, multi-functional conference halls, churches, high-end hotels, and flagship brand stores.
10
1
Share

What engine is used in the Wuling Xingchen?

Wuling Xingchen is equipped with SAIC-GM-Wuling engine. Characteristics of Wuling Xingchen engine: The Wuling Xingchen engine uses a 1.5T four-cylinder turbocharged engine with a maximum horsepower of 108kW and a peak torque of 250Nm. Based on the adjustment of this engine, this engine is biased towards home use in terms of power output, and the lower torque performance will be improved. Advantages of Wuling Xingchen engine: The Wuling Xingchen engine can significantly increase the power and torque of the engine without increasing the engine displacement. After installing a turbocharger on the engine of this car, its maximum output power can be increased by about 40% or more compared to that without a turbocharger.
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.