How to Use the Car Horn?

2 Answers
Jackie
09/03/25 8:28am
Correct usage of the car horn: 1. When driving on mountain roads with many sharp turns or S-curves, honk the horn before entering these curves to alert oncoming vehicles. 2. Slow down and honk the horn in advance when approaching intersections, forks, towns, and busy road sections. 3. Do not use the horn to alert pedestrians or non-motorized vehicles in front of the car or at intersections. 4. Horn usage is prohibited in hospitals, residential areas, schools, tunnels, and garages. Below is an introduction to the car horn: The horn is the audio signal device of a car. During driving, the driver uses it as needed and in accordance with regulations to issue necessary audio signals, warn pedestrians, draw attention from other vehicles, ensure traffic safety, and also to urge movement or convey signals.
Was this review help?
16
4
Share
StHolden
09/16/25 2:57am
As a novice who just learned to drive, I was nervous when I first encountered the car horn, but I quickly got the hang of it. The operation is actually quite simple—just locate the button in the center or on the side of the steering wheel and press firmly to sound the horn, alerting vehicles or pedestrians ahead for safety. It is typically used in safe driving scenarios, such as giving a light tap when the car in front doesn't move at a green light or warning of hazards in blind spots while turning. Avoid holding it down for too long, as this can be annoying and may even be perceived as provocative. Through practice, I've found that the horn is a crucial communication tool in urban traffic, but it must be used reasonably. If the horn doesn't work, first check whether the fuse is blown or if there's an issue with the battery. When driving, exercise restraint and only give one or two light taps when necessary—this habit has helped me avoid many minor conflicts.
Was this review help?
6
4
Share
Expand All
More Forum Discussions

Why does the BMW N55 report an electronic throttle valve fault?

BMW N55 reports an electronic throttle valve fault because the system causes the engine not to start. Fault reasons: Poor DME software application. As a result, when the engine stalls, the electronic throttle control system may occasionally get stuck at the lower limit position. Handling measures: Since the operation should follow ISTAABL, and ABL is automatically generated by the fault code. The ABL integrates steps such as VVT system running-in, mechanical resistance self-assessment, and limit position learning. It must be completed patiently. Incomplete execution of ABL will lead to repeated repairs.
4
0
Share

Does the G-Class have a starry sky roof?

The G-Class does not come with a starry sky roof as standard. Principle of the starry sky roof: Traditional starry sky roof technology uses optical fibers to transmit light from a light source to the interior roof, creating a starry sky effect. This requires inserting and securing each fiber into the roof, and fibers can only be fixed in areas without a sunroof. For models with a panoramic sunroof, a large portion of the roof cannot be covered with fibers, resulting in an incomplete starry sky pattern. Controller: The lighting component includes glass with a preset pattern and a light film, where the light film is located within the interlayer of the starry sky patterned glass and is connected to the controller. Preferably, it also includes a switch connected to the controller. Preferably, it also includes a power source connected to the switch, forming a circuit with the light film.
2
3
Share

Where is the Honda CRV key sensor located?

Honda CRV key sensor is located near the one-touch start position. Principle of the smart key: It uses radio frequency identification (RFID) technology. Typically, when the owner approaches the vehicle within approximately one meter, the door locks will automatically unlock and the anti-theft system will deactivate; when leaving the vehicle, the door locks will automatically lock and the anti-theft system will activate. When the owner enters the vehicle, the in-car detection system immediately recognizes the smart key. At this point, simply pressing the start button lightly will allow the vehicle to start normally. Throughout this process, there is no need to take out the car key. Causes of smart key malfunction: If the remote control has power but cannot unlock the doors, it may be due to the vehicle's battery being dead. In case of sensor failure, the mechanical key can be used to open the doors.
4
2
Share

What is the method for replacing the battery in the Borui car key?

The method for replacing the battery in the Borui car key is: 1. Push the marked switch upwards from the tail of the key to remove the mechanical key; 2. Use the mechanical key to press against the marked position and gently open the key casing; 3. Use a card to pry the old battery from the gaps on both sides and remove it; 4. Replace with a new battery, reinstall the casing, and return the mechanical key. Taking the 2021 Borui Navigation Edition as an example, its body dimensions are: length 4986mm, width 1861mm, height 1513mm, wheelbase 2870mm, trunk capacity 502l, and body weight 1660kg.
2
4
Share

What type of oil is used in a manual transmission car's gearbox?

Manual transmission cars use 75W gear oil. Transmission oils are divided into two types: manual transmission oil and automatic transmission oil. Manual transmission oil is gear oil, while automatic transmission oil is also known as transmission fluid or driveline oil. The steps for changing transmission oil are: 1. Drain the old oil; 2. Remove the oil pan; 3. Install the drain plug and pour in new oil. The reasons for changing transmission oil are: 1. Over time, the viscosity of transmission oil becomes diluted, reducing its lubricating and sealing properties, increasing resistance, leading to greater wear and affecting the accuracy of the hydraulic system; 2. The oil deteriorates, reducing its anti-oxidation and cooling properties, causing excessively high oil temperatures and shortening the lifespan of transmission components.
6
3
Share

How to Reset the Maintenance Light on a Mercedes-Benz Vito Commercial Vehicle?

Here are the detailed steps for resetting the maintenance light on a Mercedes-Benz commercial vehicle: Turn on the ignition: Use the function button on the left side of the steering wheel to select the maintenance mileage reminder on the dashboard; press and hold the "0" reset button at the bottom left of the dashboard for 30 seconds (keep pressing), then release it after hearing a prompt sound. Enter the maintenance reset mode: Press the menu button at the very bottom of the left side of the steering wheel once, then press the selection confirmation button at the very top of the left side of the steering wheel once to enter the maintenance reset mode. Confirm the reset: Press the menu button at the very bottom of the left side of the steering wheel once, then press the selection confirmation button at the very top of the left side of the steering wheel once to enter the maintenance reset mode; while in the maintenance reset mode, press the "0" reset button at the bottom left of the dashboard for 3 seconds and release immediately, then press the selection confirmation button at the very top of the left side of the steering wheel to select the oil type; finally, press the "0" reset button at the bottom left of the dashboard for 3 seconds and release immediately, then press the selection confirmation button at the very top of the left side of the steering wheel to confirm the completion of maintenance.
20
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.