How to Use the Auto Start-Stop Function in Audi Q5?

How to Repair a Rusted-Through Car Door?

When the metal sheet of a car is rusted through, the rusted part needs to be cut out and re-welded. Methods for repairing a rusted car door include: 1. If the rust appears on the surface and the area is small, sandpaper can be used to grind off the rust, followed by spraying a layer of anti-rust paint; 2. For small rust areas, scrape off the rust, sand with sandpaper, and then perform touch-up painting; 3. If the car door is severely rusted with large areas of paint peeling off, the rusted paint must be completely removed, followed by filling and leveling with putty, and then repainting. If the damaged area is large, repair is not recommended, and it is better to replace the entire piece. Car rust should be treated promptly, and preventive measures should be taken. Clean the car body promptly after rain, and repair any scratches or damages on the car surface immediately to avoid oxidation and rust.

8

2

Share

What Causes the Yellow Exclamation Mark on the 10th Generation Accord Dashboard?

When a yellow exclamation mark appears on the car dashboard, there are four possible scenarios: general faults, automatic transmission faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these four situations: General Faults: A triangle with an exclamation mark inside indicates a malfunction in the car's general performance, components, or functions. Common issues include parking sensor failure, fuel cutoff system intervention or malfunction, external light failure, or engine oil pressure sensor failure. It is necessary to visit a 4S shop for inspection to identify the source of the fault. Automatic Transmission Fault: A yellow gear with an exclamation mark inside is the automatic transmission fault warning light, indicating a problem with the transmission or that the transmission fluid is below the normal range. The transmission fluid should be replaced promptly. Abnormal Tire Pressure: A horizontal line under a bracket with an exclamation mark in the middle represents the tire pressure monitoring warning light. This light turns on when the tire pressure is too low. Check the car's tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark is the lighting fault indicator, signaling a malfunction in one of the car's lights. Solution: Visit a 4S shop as soon as possible for inspection and repair. Alternatively, you can perform a self-check, focusing on commonly used bulbs such as turn signals, fog lights, and interior lights to identify the issue. There is also a red exclamation mark inside a circle with parentheses, which represents a warning for the braking system. This could indicate a brake system malfunction or low brake fluid level. The braking system should be inspected immediately to avoid accidents.

11

0

Share

Is the Bestune T77 a domestic car?

The Bestune T77 is a domestic car. The Bestune T77 is a compact SUV produced by FAW Bestune, which is part of the China FAW Group. The dimensions of the Bestune T77 are 4525 mm in length, 1845 mm in width, and 1615 mm in height, with a wheelbase of 2700 mm. The Bestune T77 is the first model in the new T series of Bestune's product lineup, breaking away from the brand's previous design style and adopting a new design philosophy that gives the vehicle a more youthful appearance. In terms of exterior design, the Bestune T77 retains many elements from its concept car, featuring an overall design inspired by the concept of light and shadow folding. Detailed aspects include a hexagonal concave front grille with star-like chrome-plated matrix elements, paired with a low front end, giving it a very distinctive look. Additionally, the trapezoidal air intake design at the lower part of the front enhances the visual tension of the vehicle's front section.

6

1

Share

Where is the vehicle inspection location in Zaozhuang?

Zaozhuang vehicle inspection locations are: Location 1: Shizhong District Vehicle Performance Inspection Station. No. 17, Hengshan Road, Shizhong District, Zaozhuang City. Location 2: Zaozhuang Jiaoyun Vehicle Performance Inspection Co., Ltd. No. 79, Qingtan South Road, Shizhong District, Zaozhuang City, Shandong Province. Location 3: Zaozhuang Shengxiang Vehicle Comprehensive Performance Appraisal Center. Location 4: Tengzhou JinYun Vehicle Maintenance Factory of Tengzhou Transportation Automobile Transport Co., Ltd. No. 153, Jinghe West Road, Tengzhou City, Zaozhuang. Information about vehicle annual inspection is as follows: Vehicle annual inspection: Also known as vehicle annual check, it refers to the annual inspection of motor vehicles. Initial inspection: The inspection conducted for motor vehicles to apply for license plates is called the initial inspection. The purpose of the initial inspection is to verify whether the motor vehicle meets the conditions for applying for license plates.

6

4

Share

What Causes Overheating in a 16A Plug for New Energy Vehicle Charging?

1. Material Issues: Currently, the metal materials used for manufacturing wires are mainly divided into copper and aluminum. Research shows that at 20°C, the resistivity of copper is 1.678, while that of aluminum is 2.6548. Therefore, using aluminum-core wires for new energy vehicle charging circuits results in higher heat generation compared to copper-core wires. 2. Wire Thickness: Under the same current, the resistance is directly related to the thickness of the wire. In other words, the thicker the wire, the lower the heat generation. Generally, household electrical sockets use wires with a cross-section of 1.5 square millimeters, which can safely handle a current of 10A. A 1.7KW portable charger has a charging current of only 7.7A, so connecting it will not cause overheating. However, a 3.3KW wall-mounted charger can reach a charging current of 15A. If it draws power from a standard socket, the 1.5 square millimeter wire will overheat due to excessive charging current and may even melt the socket panel. Therefore, a 3.3KW wall-mounted charging pile must use wires of at least 2.5 square millimeters, and the socket panel should be upgraded to 16A. 3. Loose Connections: If the connections between wires, or between wires and sockets or plugs, are not tight, the resistance at the connection points will increase, leading to higher heat generation. Additionally, poor-quality sockets or those that have been used for too long may develop loose connections due to metal fatigue from repeated plugging and unplugging.

10

3

Share

Why does the booster pump keep making noise when there is no water flow?

The reasons why the booster pump keeps making noise when there is no water flow are as follows: Issues with the pressure control system: When the working pressure reaches the controlled pressure, the water pump stops working. This indicates a problem with the pressure control system. Once the pump stops, the pressure will drop. No water in the outlet direction: Since there is no water usage in the outlet direction, the pressure quickly replenishes, causing the booster pump to immediately enter standby mode. This repeated cycle results in the phenomenon of intermittent noise and stopping. Leakage in the pump outlet pipe: Due to the drop in water pressure in the pump chamber, the water pump restarts to replenish pressure, resulting in very little water flow in the outlet direction. This causes the pressure to quickly rise to the set value, prompting the booster pump to stop and maintain pressure. Once the pressure is reached, leakage causes the water pressure to drop again, and the booster pump restarts to replenish pressure. This repeated cycle leads to the phenomenon of intermittent noise and stopping.

1

2

Share

How to Use the Auto Start-Stop Function in Audi Q5?

How to Repair a Rusted-Through Car Door?

What Causes the Yellow Exclamation Mark on the 10th Generation Accord Dashboard?

Is the Bestune T77 a domestic car?

Where is the vehicle inspection location in Zaozhuang?

What Causes Overheating in a 16A Plug for New Energy Vehicle Charging?

Why does the booster pump keep making noise when there is no water flow?

Does the 2021 Touareg have a particulate filter?

What Causes the Radiator to Overheat?

Does the Jetta have a front anti-collision beam?

Can Radiator Fluid Replace Coolant?