How to Use Tesla EAP?

1 Answers
Val
07/28/25 2:52pm
Tesla EAP usage methods: 1. Operate via the mobile app by pressing the forward/backward options in the summon feature; 2. While stationary in the vehicle, press the gear stalk button twice consecutively - arrow options for front/rear movement will appear on screen to select direction; 3. Using the car key, configure summon settings in the central control screen's custom summon options. Taking Tesla Model 3 as an example, it is a mid-size electric vehicle with 2875mm wheelbase, dimensions of 4694mm(length)×1850mm(width)×1443mm(height), and all variants use ternary lithium batteries.
Was this review help?
9
5
Share
More Forum Discussions

How to Turn Off the Continuously Flashing Hazard Lights?

The hazard lights, also known as emergency flashers, can be turned on by pressing the button once and turned off by pressing it again. When you need to stop and troubleshoot, the driver should immediately turn on the hazard warning flashers and move the vehicle to a place where it does not obstruct traffic. The hazard warning flashers should remain on, and warning signs should be set up in the direction of oncoming traffic to increase the warning distance. If necessary, call the police promptly.
1
1
Share

What is the refund process for Shouqi Limousine & Chauffeur?

Open the official WeChat account "Shouqi Limousine & Chauffeur", select "Contact Buyer" in the lower right corner, then choose "Online Customer Service". In the dialog box, enter "Transfer to Human Service", and then reply accordingly as required. Reply with "Request Refund", and the customer service representative will check the account's recharge amount and bonus amount. The recharge amount can be refunded, while the bonus amount cannot be refunded. Then, the representative will ask "Are you sure to proceed with the refund? We will process the refund to the original payment method, and it will arrive within 3 business days." Simply reply with "Confirm Refund" to proceed.
18
2
Share

How to Install Dual Throttle Cables?

Adjust the clearance and tightness of the throttle handle, then test acceleration. This indicates interference in the throttle cable, which causes a rustling sound when pulled, mostly due to the cable being coiled around the handle. During operation, a "clicking" sound may occur, in which case it is best to replace with a new cable. Hold the adjustment nut and pull the cable outward by 2-3mm, then check if the clearance is appropriate. Turn the adjustment nut clockwise to tighten the cable. When the clearance returns to its pre-failure state, the cable tension is considered appropriate.
6
1
Share

How to Install a Water Plug?

Clean the sealing ring position thoroughly. Replace with a new sealing rubber ring. Cut a 6 cm long nylon rod, shaped as shown, with a small end diameter of 20 mm and length of 4 cm, followed by a step with a diameter of 35 mm. Insert it into the hole where the sealing rubber ring is located. This hole has a diameter of 20 mm. After tightly fitting it into the drainage column hole, it can be pressed into its original position. The pressure from the spring at the top of the drainage column should be slightly higher.
2
1
Share

How to Drain the Water from the Radiator?

Drain the existing water from the radiator. There is a drain valve at the bottom of the radiator. For some vehicle models, it is also necessary to drain the water from the engine block, where there is a drain plug. There is a drain valve at the bottom of the radiator. After draining the water, tighten it and add antifreeze. Simply open the drain valve at the bottom of the radiator. "Antifreeze" is a chemical solution with a low freezing point, which can drop below -60 degrees Celsius. It will not freeze due to low temperatures and will not damage the engine.
4
2
Share

How to Repair a Flood-Damaged Car?

Remove the seats and the entire floor carpet. Generally, there is a thick layer of sponge beneath the carpet. Use a vacuum cleaner to suck out the water until no more can be extracted, then place the car in a paint baking room to dry. It is recommended to use the tube heating method and avoid using fuel-fired heating. Adjust the temperature to 55 degrees Celsius, as this temperature will not damage the interior or leather. After drying, do not rush to reassemble. Use a fan to blow for several hours to remove any odors. Assemble carefully and professionally, and there will be basically no harm to the car.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.