How to use Mercedes-Benz Carlife?

Where is the child lock on the Volkswagen Lamando?

The child lock on the Volkswagen Lamando is located on the inner edge of the rear doors. There are two types of child safety locks: knob-style and toggle-style. Below are the usage precautions for the child lock: 1. For the knob-style, when setting the child safety lock, insert the key into the lock slot and turn it to the horizontal position. The door can only be opened from the outside when it is unlocked. To restore normal door operation, turn the lock slot to the vertical position. 2. For the toggle-style, slide the toggle to the locked position and then close the door. Even if the door is unlocked, it cannot be opened from the inside and must be opened from the outside. 3. The child lock, also known as the car child safety lock, is a safety device designed to ensure the safety of children sitting alone in the rear seats. It prevents the danger of children accidentally opening the door from inside while the vehicle is moving. If you find that the door cannot be opened from the inside, it is likely that the toggle-style child safety lock was accidentally activated during entry or exit. Simply reach out through the window to open the door or wait for the driver to open it, then reset the child safety lock.

15

1

Share

What to Do with China 5 When China 6 Arrives?

China 5 vehicles can still be driven. Currently, some cars already meet the China 6 standard, but China 3 and China 4 private cars are still common on the streets. Relevant details are as follows: 1. Restricting automakers: The new standard is only intended to restrict automakers, ensuring that vehicles sold must meet the China 6 standard requirements. For vehicles already purchased under the China 5 standard, they will still operate according to the emission status at the time of purchase. This means even after the China 6 standard is implemented, China 5 vehicles can be driven with peace of mind. However, their resale value may not be as high, and the cost of replacing the vehicle may increase. 2. An upgrade from China 5: The China 6 standard is an upgrade from the China 5 standard and will become one of the strictest standards globally. Compared to the China 5 standard, China 6 will strictly control pollutant emission limits. Under conditions excluding driving cycles and test influences, carbon monoxide emissions from gasoline vehicles will be reduced by 50%, total hydrocarbons and non-methane hydrocarbon emission limits will drop by 50%, and nitrogen oxide emission limits will be tightened by 42%. Overall, the China 6 standard is based on international standards and is completely different from the previous China 3, China 4, and China 5 standards.

9

2

Share

What are the benefits of carbon fiber materials?

The benefits of carbon fiber materials are as follows: 1. High performance: Carbon fiber possesses a series of excellent properties that are irreplaceable by other materials, such as being lightweight, high strength, high modulus, high temperature resistance, corrosion resistance, erosion and splash resistance, as well as good designability and composability. 2. Lightweight: The most obvious benefit of applying carbon fiber to automobiles is vehicle lightweighting, which directly affects energy savings, acceleration, and braking performance improvements. Generally, a 10% reduction in vehicle weight leads to a 6% to 8% reduction in fuel consumption, a 5% to 6% reduction in emissions, an 8% to 10% improvement in 0-100km/h acceleration, and a 2 to 7-meter reduction in braking distance. 3. Safety: Lightweighting the body can lower the vehicle's center of gravity, improving handling stability and making the vehicle safer and more stable. Carbon fiber composites have excellent energy absorption rates, with crash energy absorption capabilities six to seven times that of steel and three to four times that of aluminum, further ensuring vehicle safety. 4. Comfort: Carbon fiber composites have higher vibration damping; light alloys take 9 seconds to stop vibrating, while carbon fiber composites take only 2 seconds. 5. Reliability: Carbon fiber composites have higher fatigue strength. The fatigue strength of steel and aluminum is 30-50% of their tensile strength, whereas carbon fiber composites can reach 70-80%. Therefore, the application of carbon fiber composites in automobiles significantly improves material fatigue reliability. 6. Enhancing body development: Due to the superior designability of carbon fiber composites compared to metals, they facilitate platformization, modularization, and integration in body development. Thus, the hybrid body structure of carbon fiber and metal platforms can achieve modularization and integration compared to traditional automobile body structures, greatly reducing the number of parts, decreasing tooling investment, and shortening the development cycle.

12

3

Share

Can the Land Cruiser use 92-octane gasoline?

According to the official vehicle manual recommendation, the Land Cruiser should use 95-octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle manual, the Land Cruiser's fuel cap also indicates the recommended octane rating. Generally, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with a compression ratio between 8.6-9.9 should use 92-octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95-octane gasoline. However, with the application of new technologies, the compression ratio alone cannot determine the required gasoline grade, as high-compression engines can also be tuned to use lower-octane fuel. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline octane rating, the higher the octane number and the better the anti-knock performance. 92-octane gasoline contains 92% isooctane and 8% n-heptane, while 95-octane gasoline contains 95% isooctane and 5% n-heptane. If the Land Cruiser occasionally uses the wrong gasoline grade, simply refuel with the correct grade afterward. However, prolonged use of the wrong gasoline grade can have the following effects: For vehicles designed for lower-octane fuel, using higher-octane gasoline will not cause damage, but the increased octane rating alters the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles designed for higher-octane fuel, using lower-octane gasoline can cause engine knocking. The significantly lower octane rating lowers the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug fires, resistance builds up during the upward stroke. This resistance makes the engine run very unevenly. Mild knocking may only increase noise without significant engine damage, but severe knocking indicates serious engine issues. The vibrations not only affect driving stability but can also cause abnormal wear on pistons and cylinders, potentially leading to cylinder scoring in extreme cases.

3

0

Share

What is the normal tire pressure for Nissan Teana?

The normal tire pressure range for Nissan Teana is 2.4-2.5bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2bar in winter and reduced by 0.1bar in summer. This data is based on the international GBT2978-2008 standard. If you want to check the current tire pressure of Teana during daily driving, you can activate the tire pressure monitoring system, and the tire pressure value will be displayed on the central LCD screen of the instrument panel. The specific method is to press the square button on the left side of the steering wheel to bring up the tire pressure monitoring and display the specific tire pressure value. Generally speaking, a tire pressure above 2.8bar is too high, and a tire pressure below 2.0bar is too low. Hazards of excessive tire pressure: The friction and adhesion of the tire will decrease, affecting braking performance; it will cause steering wheel vibration and deviation, reducing driving comfort; it will accelerate the local wear of the tread pattern in the center of the tire, shortening the tire's lifespan; the vibration of the car body will increase, indirectly affecting the lifespan of other components; it will cause excessive stretching deformation of the tire cords, reducing the elasticity of the tire body, and increasing the load on the car during driving. Hazards of insufficient tire pressure: The friction coefficient with the road surface will increase, leading to higher fuel consumption; it will make the steering wheel heavy and prone to deviation, which are factors detrimental to driving safety; it will increase the movement of various parts of the tire, causing abnormal heating due to excessive rolling; it will reduce the function of the cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, causing damage to the bead area and abnormal wear; the friction between the tire and the ground will multiply, causing a sharp rise in tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to a tire blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol, an irregular circle with no seal on top and four small spikes at the bottom, with an exclamation mark inside), there are generally three reasons: Abnormal tire pressure: It usually alarms when the pressure is below 1.8bar or above 3.0bar. At this time, tire inspection and pressure adjustment are needed. Tire pressure monitoring not reset: After inflating the tires, the tire pressure was not reset in time, causing the tire pressure monitoring system to still record the original data, and the tire pressure monitoring indicator light will come on. At this time, just reset the tire pressure. Tire pressure sensor damage: The tire pressure sensor is used to monitor tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the tire pressure sensor is damaged during driving, it will also cause the tire pressure fault light to come on. For sensor damage, only a new replacement can be installed.

1

5

Share

Where is the engine number of the BMW 525 located?

The engine number of the BMW 525 is located on the engine block, specifically at the connection point between the front end of the cylinder head and the engine block. The BMW 525 is equipped with a four-cylinder turbocharged engine, which includes a low-power version of the 2.0-liter turbocharged engine, a high-power version of the 2.0-liter turbocharged engine, and a 3.0-liter inline six-cylinder turbocharged engine. The BMW 525 is a model launched by BMW Brilliance, featuring a six-speed automatic transmission, a double-joint control arm front suspension system, tire specifications of 225/50R17, and a ventilated disc braking system.

12

5

Share

How to use Mercedes-Benz Carlife?

Where is the child lock on the Volkswagen Lamando?

What to Do with China 5 When China 6 Arrives?

What are the benefits of carbon fiber materials?

Can the Land Cruiser use 92-octane gasoline?

What is the normal tire pressure for Nissan Teana?

Where is the engine number of the BMW 525 located?

Why does water drip from the chassis when the car's air conditioning is on?

How Soon Does the Volkswagen Sagitar Start Burning Engine Oil?

What to Do If China 5 Vehicles Can't Be Sold?

How to Reset the Maintenance Light on a Ford Kuga?