How to Use Cruise Control on the 10th Generation Accord?

1 Answers
SanAna
07/29/25 12:04pm
The method to activate cruise control on the 10th Generation Accord is as follows: 1. Press the CRUISE button located at the top right of the steering wheel. At this point, the cruise control system enters the ready-to-set state. 2. Accelerate the vehicle to your desired speed. 3. To end the cruise during operation, you can either press the brake pedal or press the CANCEL button to deactivate the cruise control. 4. During cruising, pressing or holding the RES button will increase the speed. Alternatively, you can press the accelerator pedal to reach your desired speed and then press RES to set the new speed. 5. During cruising, pressing or holding the SET button will decrease the speed.
Was this review help?
8
4
Share
More Forum Discussions

How to Remove Soundproofing Adhesive from Car Doors?

Alcohol, gasoline, or nail polish remover are all organic solvents that can dissolve high molecular compounds. First, peel off the adhesive decorations attached to the glass or product surface, then soak a towel in warm water and repeatedly wipe the adhesive residue twice.
8
4
Share

What Causes the Constant Illumination of the Lavida Tire Pressure Monitoring Light?

The Lavida utilizes an indirect tire pressure monitoring system, and the persistent illumination of its tire pressure warning light is most likely due to forgetting to set the initial tire pressure values. Lavida's tire pressure monitoring relies on the ABS pump to detect tire rolling circumference for pressure assessment. It requires setting default values—specifically, after inflating all four tires, you must drive for a few minutes and then long-press the SET button. A confirmation 'beep' indicates the system has recorded the preset standard values. Subsequently, if any tire's pressure falls below this threshold, the system will trigger an alert. Relevant technical details: 1. Underinflation: Low tire pressure increases tire body deformation, leading to sidewall cracks and excessive flexing. This generates overheating, accelerating rubber aging, ply fatigue, and cord breakage. It also enlarges the tire's contact patch, hastening shoulder wear. 2. Overinflation: Excessive pressure overextends tire cords, reducing elasticity and increasing driving load. Impacts may cause internal fractures or blowouts, while high pressure also accelerates tread wear and compromises puncture resistance.
15
0
Share

What is the scope of Lynk & Co 05's lifetime warranty?

The scope of Lynk & Co's lifetime warranty includes the engine, transmission, chassis, integrated control unit, etc. Some wear-and-tear parts are not covered by the lifetime warranty, such as tires, bulbs, batteries, wiper blades, spark plugs, and the four major filters. The warranty period for these wear-and-tear parts will be specified in the warranty manual or the three-guarantee certificate. Conditions for the invalidation of Lynk & Co's lifetime warranty: To enjoy the lifetime warranty, the owner must be the first owner, meaning the vehicle cannot be transferred to another person. When selling the car as a used vehicle, the lifetime warranty becomes invalid, and the buyer cannot enjoy this right. If the vehicle is scrapped, catches fire, or is forcibly scrapped according to national policies, the lifetime warranty becomes invalid. The vehicle cannot be used for non-household purposes such as official business, operation, or competition; otherwise, the lifetime warranty becomes invalid. If the vehicle is involved in a major accident or incident, such as fire, flooding, or a major traffic accident causing significant damage to the main body, the lifetime warranty becomes invalid. If maintenance and repairs are not performed according to Lynk & Co's standards, or if non-original Lynk & Co parts or parts not of equivalent quality to Lynk & Co's original parts are used, the lifetime warranty becomes invalid.
20
1
Share

Where is the spark plug of Wuling Rongguang?

The spark plug of Wuling Rongguang is installed on the side or top of the engine. In early models, the spark plug was connected to the distributor via ignition cables, but over the past decade, most car engines have been modified to directly connect the ignition coil to the spark plug. Working principle of spark plugs: The ground electrode of the spark plug is connected to the metal shell, which is threaded into the engine block through the cylinder head. The insulator primarily serves to isolate the metal shell from the central electrode. The terminal nut is the part of the spark plug that contacts the high-voltage coil. When current passes through the terminal nut and the central electrode, it ionizes the medium between the central electrode and the ground electrode, generating a spark to ignite the air-fuel mixture in the cylinder. Spark plug replacement interval: Under normal maintenance conditions, spark plugs should be replaced every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. The following standards can be referenced for maintenance replacement: Platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers.
14
2
Share

How to Handle a Vehicle Accident Where the Other Party is Fully at Fault?

Survey and damage assessment inspectors must complete on-site surveys and inspections within 1 working day after receiving notification from the insurance company's internal staff; All claims must be calculated and reviewed within 3 working days, then submitted to the claims department head for verification. Settlement and case closure.
13
4
Share

How many times should the headlights alternate between high and low beam in Subject 3?

In Subject 3, the headlights should alternate between high and low beam two or more times, typically three times. Additional information is as follows: Subject 3: Subject 3, which includes the road driving skills test and the safe and civilized driving knowledge test, is a part of the motor vehicle driver's license assessment. It is the abbreviated term for the road driving skills and safe and civilized driving knowledge test in the motor vehicle driver's examination. The content of the road driving skills test varies depending on the type of vehicle being licensed. Alternating between high and low beam operation: When an oncoming vehicle is within 150 meters, the high beam should be switched to low beam. If the other party does not switch to low beam, immediately reduce speed and continuously alternate between high and low beam to signal. If the other party still does not change, slow down and pull over to the right to yield. Avoid engaging in a battle of bright lights, as it may impair both drivers' vision and lead to an accident.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.