How to Use Cruise Control in Toyota Camry?

1 Answers
GabrielLynn
07/29/25 4:19pm
Toyota Camry's cruise control buttons are located on the right side of the steering wheel. The usage method is as follows: 1. When the vehicle speed reaches 40km/h, press the on/off key to activate the system, and the cruise control indicator light on the instrument panel will illuminate; 2. After accelerating to the desired speed, press the set key, and you can release the accelerator pedal, with the speed fixed at the current speed; 3. Use the "res+" and "set-" buttons to adjust the speed; 4. Press the brake, cancel button, or on/off key to deactivate the cruise control; 5. If the cruise control is deactivated by pressing the brake or cancel button, you can press the res key to restore the previous cruise control speed.
Was this review help?
18
1
Share
More Forum Discussions

What to Do About a Dent in the Car Door?

A small dent on the car door affects the vehicle's appearance. The following methods can be used to remove it: 1. Clean the dented area thoroughly, load the special glue into the glue gun, and plug it in to preheat for about 7 minutes. Then, select an appropriate pad—note that larger dents require larger pads, as larger pads provide greater traction. Apply the melted glue evenly onto the pad using the glue gun, then quickly press it onto the dented area and hold it gently until the glue sets. 2. Align the hole in the center of the pull bridge with the glued pad, place the nut onto the pad's screw rod, and tighten it. Continue turning the nut until the dent is pulled out and leveled. After the repair is complete, remove the tools, spray alcohol on any residual glue on the car body, and finally clean it off with a scraper. 3. Alternatively, you can take it to an external repair shop for professional dent repair, also known as light metalwork.
7
1
Share

What does 1.2t engine mean?

Engine 1.2t refers to the engine displacement of this vehicle being 1.2 liters, where the 't' stands for turbo, meaning turbocharged. The Chinese explanation of turbocharging is as follows: 1. A turbocharged engine is an engine that relies on a turbocharger to increase the intake air volume. The turbocharger (turbo) is essentially an air compressor. It uses the exhaust gases expelled by the engine as power to drive the turbine in the turbine housing (located in the exhaust passage). The turbine, in turn, drives the coaxial impeller located in the intake passage, which compresses fresh air delivered by the air filter pipe and then sends it into the cylinders. When the engine speed increases, the exhaust gas expulsion speed and turbine speed also increase synchronously, thereby enhancing the air compression level. This results in a corresponding increase in the engine's intake air volume, which can boost the engine's output power. 2. The greatest advantage of a turbocharged engine is that it can significantly increase the engine's power and torque without increasing the engine displacement. After installing a turbocharger, an engine's maximum output power can increase by approximately 40% or even more compared to when it is not equipped with a turbocharger.
8
2
Share

What are the symptoms of a car running on water-contaminated gasoline?

Using gasoline mixed with water can significantly impact a car's engine. The symptoms of a car running on water-contaminated gasoline are as follows: 1. At the moment of startup, when a piston moves upward to complete the compression work before ignition, the intake valve closes almost simultaneously, creating a sealed space inside the cylinder. Since water is incompressible, the piston will encounter significantly increased resistance as it moves upward to a certain position. However, the crankshaft driven by other working pistons is determined to push this piston to the top dead center. The accumulated water will be expelled from the cylinder when the exhaust valve opens during startup, but the damage to the connecting rod is already done. A bent connecting rod inadvertently reduces the cylinder's compression ratio and increases the engine's operational resistance, making the vehicle feel less powerful than before. 2. A slightly bent connecting rod makes the piston's movement in the cylinder extremely unstable, and higher RPMs undoubtedly accelerate its deterioration. Additionally, the piston's erratic movement in the cylinder worsens the bending of the connecting rod. The more the connecting rod bends, the more violently the piston will wobble during operation, eventually leading to damaged piston rings, cylinder walls, and the piston seizing in the cylinder. The connecting rod may also bend or break under immense pressure, and in more severe cases, a broken connecting rod can puncture the engine block directly. The engine then loses power, and the vehicle will come to a stop after a short coast.
6
0
Share

What Symptoms Can Incomplete Clutch Disengagement Damage?

Incomplete clutch disengagement is a behavior that causes severe wear to the car, with specific manifestations and causes as follows: 1. Incomplete clutch disengagement exhibits the following two phenomena: (1) When starting the car, pressing the clutch pedal beyond the free travel still results in difficulty shifting gears; if forced into gear, the car moves forward or backward before fully releasing the clutch pedal, causing the engine to stall. (2) Difficulty shifting gears while driving or inability to engage gears, accompanied by gear collision noises in the transmission. 2. The main reasons for incomplete clutch disengagement include: (1) Excessive free travel of the clutch pedal; (2) The inner ends of the release levers are not on the same plane, with some levers deformed, broken, or severely worn; (3) Warped clutch driven plate, loose rivets, or newly replaced clutch friction plates that are too thick; (4) The clutch driven plate is installed backward (front and back reversed); (5) The keyway of the driven plate hub and the spline teeth of the transmission's first shaft have insufficient clearance or are stuck, making movement difficult.
20
2
Share

Where is the license plate starting with Shan A from?

License plates starting with Shan A do not exist. Basic information about license plates is as follows: 1. The first character of a license plate is a Chinese character: it represents the abbreviation of the province where the vehicle is registered. For example, Sichuan is represented by 'Chuan', Beijing by 'Jing', Chongqing by 'Yu', and Shanghai by 'Hu'. 2. The second character is an English letter: it represents the code for the prefecture-level city where the vehicle is registered. The general rule is that 'A' stands for the provincial capital, 'B' for the second largest city in the province, 'C' for the third largest city, and so on. 3. Yellow license plates are for large vehicles, blue plates for small vehicles, and black plates for foreign-funded enterprises or embassy vehicles. Military license plates follow military numbering rules, which are different from civilian plates, but they all have white backgrounds with red characters. Police vehicle plates follow similar numbering rules as civilian plates, except that the last character is not a number but a red 'Jing' (police) character.
3
5
Share

What car has the character 'Song' on it?

A car with the character 'Song' on it is a BYD vehicle. The exterior dimensions of the car are 4600mm in length, 1830mm in width, and 1700mm in height, with a wheelbase of 2660mm and front/rear track width of 1560mm. It is a 5-door, 5-seat compact SUV. The car is equipped with a 1.5-liter turbocharged engine, delivering a maximum power of 118 kW at 5200 rpm and a maximum torque of 245 Nm. The BYD Song features MacPherson independent front suspension, multi-link independent rear suspension, full-time electric four-wheel drive system, tire pressure monitoring, vehicle stability system, and cruise control system.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.