How to use cruise control in Teana?

1 Answers
Simoes
07/30/25 10:12am
The cruise control buttons of Teana are all located on the right side of the steering wheel, and can be operated through these buttons. The following are the conditions for using cruise control: 1. The road section should be a closed section, such as a highway. On roads with complex traffic conditions, the danger of driving is higher when using cruise control, and frequent braking will make the cruise control state unstable, losing the meaning of cruise control. 2. It is prohibited to use in rainy or snowy weather, as there are many sudden situations in such weather. 3. It is prohibited to use on mountain roads or roads with many curves. These sections require slowing down and controlling the speed to ensure safety. 4. It is prohibited to use when there are many vehicles on the road. When there are many vehicles, the distance between cars is close, and there are many sudden situations, so it is necessary to pay attention to the surrounding traffic conditions at all times.
Was this review help?
4
0
Share
More Forum Discussions

How to Bleed Air from the Cruze Radiator?

Methods to bleed air from the Cruze radiator: 1. Start the car until the water temperature reaches 90 degrees, then turn off the engine and let it cool down to room temperature; 2. Open the driver's door, pull the hood release lever, and lift the hood; 3. Unscrew the radiator cap to release the internal high-pressure gas; 4. Top up the coolant to the MAX level in the radiator overflow tank to complete the operation. Taking the 2018 Cruze as an example, it belongs to the compact car category, with a body size of 4450mm in length, 1807mm in width, 1459mm in height, and a wheelbase of 2700mm. The front suspension of this car is a MacPherson independent suspension, and the rear suspension is a torsion beam non-independent suspension.
13
3
Share

What to Do When Headlights Get Foggy from Water Ingress?

Solutions for foggy headlights due to water ingress are as follows: 1. Turn on the headlights: This method works when the fogging is minimal and caused by temperature differences. Keep the headlights on for a while. The heat will help the moisture evaporate and escape through the vent tubes, which generally does not damage the headlights or electrical circuits. 2. Remove and reseal the headlight assembly: Open the sealant, remove the headlight, and carefully inspect the interior for any damage. If no damage is found, separate the lens from the assembly, dry and blow-dry each part thoroughly, then reseal with new sealant. 3. Replace the lens or entire headlight: This is necessary when the lens is damaged, allowing moisture to enter and form fog. Damage can occur from road debris, such as flying stones or foreign objects hitting the headlight while driving.
9
5
Share

Can Alcohol Be Used for Disinfecting the Car Interior?

Alcohol can be used for disinfecting the car interior, but it is important to dilute 75% concentration alcohol and then use a towel dipped in a small amount to wipe necessary contact points such as the steering wheel and gear lever. However, alcohol should not be used on genuine leather seats, sofas, or steering wheels, as alcohol is an organic solvent that can cause damage to genuine leather. Methods for disinfecting the car: 1. Use disinfectant sprays or wipes on the interior to achieve disinfection and sterilization through chemical action; 2. Utilize a car-specific disinfectant machine to generate high-concentration ozone, which is then delivered into the car for disinfection and sterilization; 3. Clean with ordinary detergent, apply protective or dry-cleaning care wipes, clean the car cabin, carpets, floor mats, and seat covers, then spray cleaning and sterilizing agents, and use high-temperature steam for disinfection.
16
0
Share

How to activate cruise control on GAC Trumpchi GS4?

To activate the cruise control function on the GAC Trumpchi GS4, press the CRUISE button. Here are the relevant details: 1. The cruise control switch is located in the functional area on the right side of the steering wheel. The button functions are as follows: CRUISE (turn on/off cruise control); SET minus (set speed/decelerate); RES plus (accelerate/resume cruise control); CANCEL (pause cruise control). 2. Pausing/resuming cruise control: Press the brake pedal or the CANCEL button to temporarily stop cruise control. At this time, the cruise light will change from green to white. If the vehicle speed is not lower than 40km/h, pressing RES will resume cruise control at the previously set speed. When the vehicle speed drops below 40km/h, the stored speed will be lost, and the previous cruise speed cannot be restored.
5
1
Share

What kind of transmission does the Fengguang 580Pro use?

Fengguang 580Pro is equipped with a 5-speed manual transmission and a CVT transmission. The transmission consists of a gear transmission mechanism and a gear control mechanism, and its functions are: 1. To keep the gear shifting system clean; 2. To provide lubrication and extend the life of the transmission device; 3. To dissipate heat and provide sealing. The Fengguang 580Pro is a mid-size SUV produced by Dongfeng Xiaokang Motors, with dimensions of 4715 mm in length, 1845 mm in width, and 1715 mm in height, and a wheelbase of 2780 mm. In terms of power, the Fengguang 580Pro is powered by a 1.5-liter turbocharged engine, with the high-power version delivering a maximum horsepower of 180 hp and the low-power version delivering a maximum horsepower of 150 hp.
3
2
Share

What is the difference in fuel consumption between 1.5L and 1.5T?

1.5L and 1.5T have a difference of about 0.3L per 100 kilometers in fuel consumption. The actual fuel consumption is related to road conditions, driving habits, and other factors. Here are ways to reduce fuel consumption rate: 1. To clarify various measures for reducing fuel consumption rate, one can start from the principle. Reasonably organize the combustion process to improve the cycle indicated efficiency. Improving indicated efficiency not only enhances the power performance of the internal combustion engine but also improves its economic performance. 2. Improving the mechanical efficiency of the internal combustion engine can enhance both its power and economic performance. This mainly relies on reasonably selecting various thermal and structural parameters, adopting structural and process measures to reduce friction losses and the power consumed by driving auxiliary mechanisms such as water pumps and oil pumps, as well as improving the engine's lubrication and cooling.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.