How to Use a Volkswagen Car Jack?

1 Answers
LaSadie
07/25/25 3:43pm
Volkswagen car jack usage instructions are as follows: 1. Take out the car jack from the vehicle; 2. Locate the jacking support point under the side door panel of the car; 3. Position the jack at the support point; 4. Use the lever to raise the jack, turning clockwise to lift and counterclockwise to lower; 5. After use, store the jack back in the vehicle. Additional relevant information: 1. The body dimensions of the Volkswagen CC 2021 model are: length 4865mm, width 1870mm, height 1459mm, with a wheelbase of 2841mm. 2. It is equipped with a 2.0L turbocharged engine, with a maximum horsepower of 186ps and a maximum power output of 137kw.
Was this review help?
6
0
Share
More Forum Discussions

Does the new Sylphy have anti-collision beams?

The new Sylphy is equipped with front and rear anti-collision beams. Here is some knowledge about anti-collision beams. The function of anti-collision beams: Since the rear anti-collision beam is hidden inside the rear bumper, many car owners are completely unaware that their vehicle lacks a rear anti-collision beam and do not understand its actual purpose. Some owners who are aware of the function of rear anti-collision beams go to great lengths to have them installed. In many cases, it serves merely a decorative role. The real safety protection comes from the anti-collision beam inside the bumper. Principle of anti-collision beams: U-shaped channels formed by stamping cold-rolled steel plates.
3
3
Share

How Often Should Spark Plugs Be Replaced in a Car?

Under normal maintenance conditions, car spark plugs should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. The following standards can be referenced for maintenance and replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the plastic cover of the engine, and remove the high-voltage wires. Mark the position of each cylinder to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any external debris such as leaves or dust and ensure they are thoroughly cleaned. Place the new spark plugs into the spark plug holes, hand-tighten them a few turns, and then use the socket to tighten them further. Reinstall the removed high-voltage wires in the firing order and secure the cover.
7
3
Share

How many types of vehicle insurance are needed?

You need to insure compulsory traffic insurance, vehicle damage insurance, third-party liability insurance, passenger liability insurance, and comprehensive theft insurance. Below is relevant information about motor vehicle insurance: 1. Definition of motor vehicle insurance: Motor vehicle insurance, also known as auto insurance (abbreviated as car insurance), refers to a type of commercial insurance that covers liability for personal injury, death, or property damage caused by natural disasters or accidents involving motor vehicles. 2. Development of motor vehicle insurance: The true development of motor vehicle insurance occurred after World War II. On one hand, the popularity of automobiles made road accidents a widespread social hazard; on the other hand, many countries included third-party liability for various motor vehicles, including cars, within the scope of compulsory insurance. Therefore, motor vehicle insurance has become a universally significant insurance business globally.
11
3
Share

What Causes One Brake Light to Work While the Other Doesn't?

Reasons for one brake light working while the other doesn't: 1. It is very likely due to a burnt-out filament in the brake light. After prolonged use, aging is normal, which can cause the brake light to malfunction. In this case, it needs to be replaced promptly. 2. Of course, it could also be an issue with the wiring, which would require a professional to diagnose and fix. 3. Another possibility is a faulty brake light switch. Additional Information: A non-functioning brake light will cause the vehicle to fail the annual inspection. Current inspection standards are strict, and brake lights must be operational because one of the steps involves uploading a photo of the brake lights—if they don't work, the vehicle will not pass. Vehicle annual inspection refers to the mandatory testing required for all vehicles with official license plates and registration certificates. It is essentially an annual 'health check' for the vehicle, conducted in accordance with the 'Technical Conditions for Motor Vehicle Operation Safety,' to promptly identify and eliminate potential safety hazards, encourage proper vehicle maintenance, and reduce the likelihood of traffic accidents—commonly referred to as a vehicle inspection.
6
2
Share

How to Rent a Car for Travel?

After selecting a car rental company, choose a vehicle and complete the paperwork to sign the contract. Here are some considerations for self-drive car rentals: 1. Test Drive in Advance: To ensure safety and avoid unnecessary issues during vehicle handover, a test drive is an essential step. The rental company can assess the driver's skills, while the renter can familiarize themselves with the car's performance. 2. Handling Violations and Accidents: Many renters recklessly run red lights or park illegally, assuming the rental company will cover their violations. However, this is not the case. According to regulations, any traffic violations during the rental period will be verified and directly recorded on the renter's driving license, along with the corresponding fines. 3. Remember the Rental Company's Service Number: In case of emergencies while driving, renters should first report to the traffic police and then notify the car rental company. 4. Insurance: The basic insurance purchased when renting a car only covers major accidents with high costs. Minor incidents are typically excluded. For more comprehensive coverage, it's advisable to also purchase a zero-deductible insurance policy.
2
5
Share

What Causes the Front Wheels to Make a Clicking Sound When Turning?

The reasons for the front wheels making a clicking sound when turning are as follows: 1. Disc brake noise: This occurs when the brake shoe support plate, damping spring plate, or guide plate of the disc brake is damaged, deformed, or detached, causing the gap between the brake shoe and the caliper support frame to increase, leading to mutual impact and noise. You can visit a repair shop to fix the deformed parts or replace the detached ones. 2. Front suspension ball joint noise: This happens when the gap between the ball joint and its seat becomes larger, causing severe looseness, which results in intermittent and irregular noise in the front axle area. It is necessary to go to a repair shop to replace the parts.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.