···
Log in / Register

How to Unfasten the Middle Seat Belt in Haval M6?

1 Answers
LeRuby
07/29/25 4:25am
The seat belt is inside the vehicle. If the owner wants to unfasten the seat belt, they must open the car door and enter the vehicle. You can use a key or a flathead screwdriver-like hard object to insert into the small hole in the middle of the seat belt buckle to unfasten it. Pinch the button with both hands and pull it outward (horizontally relative to the car body). The button cover will come off outward; then, move the button up and down. After adjusting the position to the desired level, stop pulling the button. Fine-tune the height up and down. When you hear a click, it means the height adjustment is properly set. Car seat belts are devices in vehicles designed to reduce passenger injuries when the car body is subjected to a violent impact, ensuring the safety of both passengers and the driver.
Was this review help?
19
1
Share
More Forum Discussions

What are the reasons for the Sorento's high fuel consumption?

Abnormal fuel consumption can be caused by aging spark plugs, carbon buildup in the throttle, or insufficient tire pressure. 1. Reasons: In most cases, it is due to the owner overfilling the fuel tank, causing excess gasoline that is not burned in the form of vapor. Normally, each vehicle is equipped with an activated charcoal canister on the right side of the engine compartment, which is specifically designed to absorb fuel vapors. When starting the engine, the activated charcoal canister absorbs some of the fuel vapors, but excess gasoline cannot evaporate through the activated charcoal canister and may flow out through the air pipe. 2. Reducing fuel consumption: Apart from road conditions, driving habits also play a role in reducing fuel consumption. Avoid prolonged idling to warm up the car, avoid sudden acceleration, avoid unnecessary lane changes and overtaking, make good driving judgments, and avoid sudden braking.
6
2
Share

Why is the dashboard off light always on?

The off light in the vehicle's dashboard is the anti-skid deactivation warning light. When this light is on, it serves to remind the driver that the vehicle's anti-skid system has been turned off. At this point, the driver can continue to drive cautiously or pull over as soon as possible to reactivate the vehicle's anti-skid function. Below is relevant information: 1. Definition of the vehicle anti-skid system: The vehicle anti-skid system uses an ABS/ASR electronic control unit to determine the wheel slip rate and vehicle speed based on signals from the wheel speed sensors. The electronic control unit adjusts the throttle opening and brake pressure to regulate the wheel slip rate, preventing the vehicle from skidding during driving. 2. Situations for using the anti-skid system: The vehicle's anti-skid system is enabled by default. The system primarily analyzes information from sensors to ensure optimal dynamic balance during driving. In rainy or snowy conditions, the anti-skid system may be temporarily turned off, as the vehicle is prone to skidding on snow-covered or heavily waterlogged roads. In such cases, the vehicle's computer will automatically detect wheel slippage and limit engine power output to a necessary extent.
14
3
Share

Can I replace my driver's license photo during the Subject 3 test?

You can replace your driver's license photo during the Subject 3 test. The photo for the driver's license is stored in the file, and you need to find the place where the file is submitted to replace it. If it is not convenient to replace it, you can also reapply for a replacement after obtaining the driver's license. However, you cannot change the photo yourself, otherwise the driver's license will be considered a fake. Here is some additional information: 1. Method for replacing a lost driver's license: According to Article 54 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" (Order No. 123 of the Ministry of Public Security), if a motor vehicle driver's license is lost, the motor vehicle driver shall apply for a replacement to the vehicle management office of the place where the driver's license was issued. When applying, you should fill out an application form and submit relevant certificates and vouchers. 2. Fill out the relevant application form: Citizens who need to replace a lost driver's license should bring relevant certificates to the vehicle management office and fill out the "Motor Vehicle Driver's License Application Form" and the "Motor Vehicle Driver's License Replacement Application Form". After paying the relevant fees for the replacement, you can receive a new version of the driver's license.
7
5
Share

What Causes the Jerking Sensation When Accelerating in First and Second Gears?

The jerking sensation when accelerating in first and second gears is caused by the difference in gear ratios. This phenomenon is normal and unavoidable for every driver, though it may be more noticeable for novice drivers. The lower the gear, the larger the gear ratio, and the more pronounced this phenomenon becomes—with first gear having the largest ratio. In higher gears, as the gear ratio decreases and the two gears become more similar in size (or even with the driving gear being smaller), the engine's braking effect weakens significantly. Precautions for Clutch Control: 1. Correct Clutch Pedal Posture: Place the ball of your foot on the clutch pedal with your heel touching the ground. When the clutch is fully depressed, keep your knee slightly bent. Avoid using only your toes or lifting your heel, as this may lead to insufficient force or slipping. 2. Depressing the Clutch: Press it all the way to the floor to avoid prolonged semi-engagement, ensuring complete separation and preventing wear. 3. While Driving: Do not release the clutch too quickly or deliberately rev the engine too high, as this accelerates clutch wear.
3
4
Share

What type of vehicle is used to transport sand?

Vehicles used for transporting sand are typically heavy-duty trucks. Here is relevant information: 1. Composition of heavy-duty trucks: Heavy-duty trucks consist of four main components: the engine, chassis, body, and electrical system. Operation primarily involves the engine and chassis, with the chassis including the transmission system, running gear, steering system, and braking system. 2. Major manufacturers: Currently, there are nearly 30 manufacturers in China engaged in heavy-duty truck production. The top nine in terms of market share are FAW, Dongfeng Group, Sinotruk, Shaanxi Automobile Group, Foton Motor, Beiben Trucks, SAIC Hongyan, Hualing Automobile, and JAC Motors.
18
0
Share

Where is the Civic's air intake located?

The Civic's air intake is positioned relatively high. Upon opening the engine compartment, you'll find the black box on the right side which serves as the air intake. 1. Introduction: The air intake is where the engine draws in air, typically visible only when the engine hood is opened. Its front placement corresponds with the engine's front position. The front "grille" is followed by the radiator placement. The radiator cools the engine, requiring airflow for effective heat dissipation - maximum frontal airflow occurs during vehicle movement, hence the front positioning. 2. Principle: Unrestricted airflow is essential to maintain sufficient intake pressure; greater air intake enables increased fuel injection, thereby enhancing engine power.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.