How to Turn On the Windshield Washer Spray?

1 Answers
GemmaFitz
07/29/25 11:10pm
Method to activate the windshield washer spray: The windshield washer spray switch is located on the control lever on the right side of the steering wheel, which is the wiper control lever. Pushing this lever forward will activate the windshield washer spray. In some vehicles, you need to pull the lever backward to spray. The spray nozzles on the engine hood are used to spray washer fluid to clean the front windshield. The spray nozzles are connected to the washer fluid reservoir, which contains a pump. Washer fluid is a car product that every car owner will encounter during vehicle use. The washer fluid needs to be added to the washer fluid reservoir, which is located in the engine compartment. Washer fluid has cleaning and antifreeze functions, helping to remove stains and dust from the front windshield, thus preventing impaired driving visibility.
Was this review help?
6
4
Share
More Forum Discussions

What to Do When Soy Milk Spills in the Car and Causes Odor?

Maintain good ventilation inside the car. For new cars, it is advisable to develop the habit of driving with windows open for ventilation within the first six months. When parking, you can leave the car doors open for ventilation. Prepare a basin of hot water, soak a towel in it, wring it out slightly, and then wipe all the seats inside the car.
2
5
Share

How to Test a Single-Wire Oil Pressure Switch?

Disconnect the oil pressure switch connector A from the engine oil pressure switch B. Check for continuity between the oil pressure switch terminal and the engine (ground). There should be continuity when the engine is stopped. There should be no continuity when the engine is running.
2
5
Share

How are unregistered motorcycles generally handled?

Generally, unregistered motorcycles that are seized will first undergo mandatory traffic law education, followed by fines. If a traffic accident occurs, civil compensation will be required, and the rider may face criminal detention or even criminal liability.
6
3
Share

How to Position the Car Hood Support Rod?

To open the car hood, the hood support rod clip needs to be placed into the hole in the upper left corner to secure the car hood, facilitating inspection of engine compartment issues. The hood support rod clip is generally fixed on the car front apron or radiator frame.
6
2
Share

Where Should Temporary License Plates Be Placed?

Temporary license plates generally come in two pieces, one to be affixed on the front windshield and the other on the rear windshield. If a new car does not display temporary license plates, it cannot legally be driven on the road. Here is some additional information: 1. About temporary license plates: Temporary license plates are provisional motor vehicle plates applied for, usually valid for 15 days. New cars can apply for temporary plates before official registration, but they can only do so up to three times. After obtaining temporary plates, it is essential to promptly proceed with the formal registration to ensure the vehicle's normal use and avoid unnecessary complications. The cost of a temporary plate is 5 yuan per piece. Driving a new car without temporary plates can result in a fine of 200 yuan, 12 demerit points, and temporary vehicle seizure. 2. Precautions regarding temporary license plates: (1) After purchasing a new car, you need to apply for temporary plates at the local vehicle management office. (2) When the vehicle is registered and official plates have been issued, you must apply for temporary plates at the vehicle management office and display them on the car to drive it back to the local area. (3) If the vehicle has not been registered locally but needs to be modified in another location, you must obtain temporary plates locally to drive the car to the modification site. After modification, you need to apply for temporary plates again from the local vehicle management office to drive the car back. (4) If the car is not registered but needs to be driven on the road, you must apply for temporary plates locally.
4
5
Share

What to Do When an Electric Vehicle's Air Conditioning Isn't Cooling?

Locate the glove box and proceed with disassembly. Typically, this will reveal the position of the air conditioning filter housing. Remove the filter cover to access the filter. When extracting the filter, it often cannot be removed in one piece. The filter needs to be bent into a curved shape. The same applies during installation—bending is required to fit it back in place.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.