How to Turn on the Low Beam Headlights on the Qoros 5?

Can you drive over the white grid lines at intersections?

Yellow grid lines are guiding lines, and you should not drive over them. Below is a classification of traffic markings: 1. By shape: Lines: Solid or dashed lines marked on the road surface, curbstones, or vertical surfaces. Character markings: Text, numbers, and various graphic symbols marked on the road surface. Raised pavement markers: Fixed on the road surface, these raised marking blocks serve as traffic lines, used on highways or other roads to mark centerlines, lane dividers, edge lines, as well as curves, entrance/exit ramps, guiding lines, road narrowing, and road obstacles. Delineators: Indicate the direction of the road and the boundaries of the traffic lanes, continuously and symmetrically placed along the left and right sides of the road. 2. By installation method: Longitudinal markings: Lines set along the direction of traffic. Transverse markings: Lines set at an angle to the direction of traffic. Other markings: Character markings or other forms of markings. 3. By function: Indicative markings: Lines that indicate traffic lanes, direction of travel, road edges, sidewalks, and other facilities. Prohibitive markings: Notify road users of special regulations such as compliance, prohibition, or restrictions that drivers and pedestrians must strictly adhere to. Warning markings: Alert drivers and pedestrians to special road conditions, increasing vigilance and preparing them to take preventive or responsive measures.

13

0

Share

How far can you drive if the coolant pipe bursts?

After the water pipe bursts, the car cannot continue to drive. You must repair the pipe and add water or coolant before you can continue driving. If the car does not overheat (boil), the burst is caused by poor quality or aging of the pipe. Replacing it with a high-quality pipe will solve the problem. No need to worry. Extended content: If the car boils, the following checks should be performed: 1. Insufficient engine coolant. 2. Faulty water temperature sensor or gauge. 3. Driving downwind or prolonged low-speed, high-load driving in hot seasons. 4. Ignition timing too early or too late. 5. The louver cannot fully open. 6. The air-fuel mixture is too lean or too rich. 7. The radiator is externally dirty or internally scaled, causing poor heat dissipation. The radiator needs to be cleaned or replaced. 8. The fan clutch engages too late, or the cooling fan is not working, the fan rotation resistance is too high, the blades are installed backward, or the blades are damaged. 9. The electric fan performs poorly or lacks high speed. 10. Excessive carbon deposits in the combustion chamber. 11. The water pump belt is too loose. 12. Issues with the three-way catalytic converter. 13. Air passing through water in the cylinder head gasket failure. 14. The thermostat does not open properly and needs replacement. 15. Blockages in other water pipes, elbows, or water passages. 16. The water pump is not working well (insufficient coolant circulation).

3

Share

What are the tire specifications for the 10th-generation Civic?

The 10th-generation Civic comes with two tire specifications: 215/50R17 and 215/55R16. In 215/50R17, the first number 215 indicates the tire width is 215mm, 50 represents the aspect ratio of 50% (meaning the sidewall height is 50% of the tire width), and 17 denotes the rim diameter in inches. The letter "R" stands for radial tire. Similarly, in 215/55R16, 215 indicates the tire width is 215mm, 55 represents the aspect ratio of 55%, and 16 denotes the rim diameter in inches. The letter "R" stands for radial tire. The tire brand for the 10th-generation Civic is YOKOHAMA, and the spare tire is non-full size. If you want to replace the tires yourself, follow these steps: Retrieve the spare tire and jack. Position the jack under the vehicle frame near the tire to be replaced, ensuring it contacts the metal part of the frame. Raise the jack until it supports the car. Ensure the jack is positioned correctly under the vehicle and forms a right angle with the ground. Remove the hubcap and loosen the nuts counterclockwise. Do not fully remove the nuts yet—just enough to reduce resistance. Keeping the tire on the ground during initial loosening ensures the nuts turn, not the tire. Continue turning the nuts counterclockwise until they come off. Repeat this for all lug nuts and remove them completely. Place the new tire on the wheel hub, carefully aligning the tire rim with the wheel bolts. Install the lug nuts and hand-tighten them until all nuts are snug. The tire replacement is now complete. Besides the specifications, tires also display the following common data: Tire cord material: Indicated by Chinese pinyin, such as M for cotton cord, R for rayon cord, N for nylon cord, G for steel cord, and ZG for steel radial cord. Speed rating: Indicates the maximum speed the tire can sustain under specified conditions. Letters A to Z represent certified speed ratings from 4.8 km/h to 300 km/h. Common speed ratings include: Q: 160 km/h; H: 210 km/h; V: 240 km/h; W: 270 km/h; Y: 300 km/h. Rim specification: Indicates the compatible rim size for practical use, such as "Standard Rim 5.00F."

9

1

Share

What to Practice for the First Time in Subject 2 Driving?

Subject 2 first-time driving practice focuses on clutch control. Subject 2, also known as the small road test, is part of the motor vehicle driver's license assessment, specifically referring to the field driving skills test. For small vehicles (C1/C2), the exam includes the following five mandatory items (some regions may have a sixth item, highway card collection): Reverse Parking: Park the car in the designated reverse parking spot within the allotted time without crossing the yellow boundary lines on either side. Slope Fixed-point Parking and Starting: Stop the car at the designated slope starting point and start smoothly within the time limit, avoiding overtime and crossing lines. Right-angle Turn (commonly known as 90-degree turn): Complete the turn at a right-angle intersection within the specified time without touching the yellow boundary lines on either side. Parallel Parking: Slowly drive the car into the side parking spot within the time limit without touching the yellow boundary lines. Curve Driving (commonly known as S-curve): Slowly enter the S-shaped intersection and smoothly navigate through the designated route without crossing the yellow boundary lines. Practice Driving Tips: Overtaking and Lane Changing: Be decisive and firm when overtaking or changing lanes, staying as close as possible to the vehicle in front, especially on two-way lanes, to save time. Always check the traffic in the adjacent lane via the rearview mirror, assessing both distance and the speed of the following vehicle. Listening to Engine Sounds: Unusual noises occur when the speed is high but the gear is low, or when dragging the gear. Similarly, abnormal sounds and vehicle shaking can happen when driving at low speed in a high gear. Avoid Frequent Neutral Gear Usage: While coasting in neutral is possible at low speeds without compromising safety, it consumes more fuel for fuel-injected vehicles. Never coast in neutral when going downhill, as it can lead to brake failure and potential loss of vehicle control if the engine stalls.

18

4

Share

What is the passing score for the driving license test subject one?

The passing score for the driving license test subject one is 90 points. There are 100 questions in total, consisting of single-choice questions and true/false questions, with each question worth 1 point, totaling 100 points. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," if a candidate answers 11 questions incorrectly during the test, the system will automatically submit the test and end the exam. Subject one, also known as the theoretical test or driver's theory test, is part of the motor vehicle driving license assessment. The test content includes driving theory basics, road safety laws and regulations, local regulations, and related knowledge. The test is conducted on a computer, with a time limit of 45 minutes. The content of the subject one test includes: regulations on driving licenses and motor vehicle management; road traffic conditions and rules; traffic safety violations and penalties; regulations on road traffic accident handling; basic knowledge of motor vehicles; local regulations; knowledge of braking systems and safety devices for large and medium-sized passenger and cargo vehicles; specialized knowledge for wheeled self-propelled machinery, trams, and trolleybuses. Notes for the subject one test: Candidates should pay attention to their attire, no slippers are allowed, and electronic devices and bags are prohibited in the examination room. Bring your ID card and queue to enter the waiting hall. Observe the instructions and procedures on the large screen, and store personal belongings in the lockers before entering the examination room. Upon entering, the identity verification station will assign a seat. Once seated, the test begins. Ensure the camera is aligned with you and follow exam discipline. If you fail the first attempt, there is a same-day retake. If you fail again, you must pay to reschedule. After the test, queue to collect the score report and sign it. Without a signature, the result is invalid. There is no limit to the number of times you can schedule the subject one test. Each subject can be taken once, with one retake allowed if you fail. If you do not take the retake or fail the retake, the test ends, and the applicant must reschedule. In contrast, subjects two and three have only five attempts each. Subjects two and three can be rescheduled ten days after the previous attempt. If you fail the subject three safety and civilized driving knowledge test, the passing score for the road driving skills test remains valid. There are three subjects in the driving test: subject one, subject two, and subject three. Subject one refers to the test on road traffic safety laws, regulations, and related knowledge. Subject two refers to the field driving skills test. Subject three is divided into two parts: road driving skills and safety and civilized driving knowledge. The safety and civilized driving knowledge test is conducted after subject three, so it is commonly referred to as subject four. However, the official term (as per the Ministry of Public Security Order No. 123) does not include the term "subject four."

4

5

Share

How long after registering for a driver's license can you take the Subject 1 test?

The time varies for different types of driver's license tests. Registration at the driving school is only preliminary. After registration, the driving school submits the materials to the vehicle management office. Upon success, the vehicle management office will issue a serial number, indicating successful registration. Once registered, you can schedule the Subject 1 test. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," Subject 1 consists of 100 multiple-choice and true/false questions, each worth 1 point. If 11 questions are answered incorrectly during the test, the system will automatically submit the test and end the exam. Subject 1 test content: Regulations on driving licenses and motor vehicle management; Road traffic conditions and regulations; Road traffic safety violations and penalties; Road traffic accident handling regulations; Basic knowledge of motor vehicles; Local regulations; Knowledge of braking systems and safety devices for large and medium-sized passenger and freight vehicles; Special knowledge for wheeled self-propelled machinery, trams, and trolleybuses. Subject 1 test notes: During the test, students should pay attention to their attire—no slippers are allowed. Electronic devices and bags are not permitted in the examination room. Bring your ID card and queue to enter the waiting hall. Observe the precautions and procedures on the large screen and store personal belongings in lockers before entering the examination room. Upon entering, the identity verification station will assign a seat. After finding your seat, begin the test. Ensure the camera is aligned with you and follow exam discipline. If you fail the first time, there is a retake opportunity on the same day. If you fail again, you must pay to reschedule. After the test, queue to collect your score sheet and sign it. Failure to sign renders the result invalid. There is no limit to the number of times you can schedule the Subject 1 test. Each subject can be taken once, and if you fail, you can retake it once. If you do not take the retest or fail the retest, the exam is terminated, and you must reschedule. For Subject 2 and Subject 3, there are only 5 exam attempts. Subject 2 and Subject 3 tests must be scheduled 10 days later. If you fail the Subject 3 safe and civilized driving knowledge test, the passed road driving skill test results remain valid. There are three subjects in the driver's test: Subject 1, Subject 2, and Subject 3. Subject 1 refers to the road traffic safety laws, regulations, and related knowledge test; Subject 2 refers to the field driving skills test; Subject 3 is divided into two parts: road driving skills and safe and civilized driving knowledge test. The safe and civilized driving knowledge test is conducted after Subject 3, so it is commonly referred to as Subject 4. However, the official term (as per the Ministry of Public Security Order No. 123) does not include "Subject 4."

12

5

Share

How to Turn on the Low Beam Headlights on the Qoros 5?

Can you drive over the white grid lines at intersections?

How far can you drive if the coolant pipe bursts?

What are the tire specifications for the 10th-generation Civic?

What to Practice for the First Time in Subject 2 Driving?

What is the passing score for the driving license test subject one?

How long after registering for a driver's license can you take the Subject 1 test?

What Does a Crossover Vehicle Mean?

What are the differences between Xiangling M1 and M2?

Are the Three Major Components of the Eclipse Cross Domestic or Imported?

What Causes the Abnormal Noise When Pressing and Releasing the Clutch?