How to Turn on the Hot Air in Volkswagen Magotan's Air Conditioning?

3 Answers
VonGabriella
07/29/25 2:03pm
To turn on the hot air in Volkswagen Magotan's air conditioning: With the car started, first press the AUTO button on the air conditioning control panel to activate the car's air conditioning. Then, rotate the temperature control knob to the red zone to turn on the hot air. The red zone represents hot air. If the AC button is lit, it needs to be turned off as it controls the air conditioning compressor, which is only used for cooling. Taking the 2020 Volkswagen Magotan Comfort Edition as an example, its body dimensions are 4865mm in length, 1832mm in width, and 1471mm in height, with a wheelbase of 2871mm and a fuel tank capacity of 66 liters. This model is equipped with a 1.4L turbocharged engine, delivering a maximum power of 110kW and a maximum torque of 250Nm, paired with a 7-speed dual-clutch transmission.
Was this review help?
14
4
Share
DiRichard
08/13/25 5:51am
Turning on the heating in my Volkswagen Magotan is quite simple. First, start the engine and let it warm up for a few minutes until the water temperature rises for it to be effective. Then, look at the center console panel, where there's a large knob. Turning it counterclockwise adjusts to the cooler blue zone for cold air, and turning it clockwise to the red high-temperature end gives you hot air. The fan speed determines the airflow rate, and I prefer manually increasing it a bit to warm up the car faster. If the car has automatic air conditioning, simply press the AUTO button to set the target temperature, like 24 degrees, and the system will automatically adjust the heating. Note that the air might be cool at first, so be patient. The direction of the air vents is quite important; pointing them towards the feet or the front window defrosts faster. Don’t accidentally turn on the heating in summer, and regularly maintain the air filter to prevent clogging—replacing it periodically can improve performance.
Was this review help?
17
4
Share
Expand All
VanMaria
10/10/25 6:53am
After starting the vehicle, wait for the engine to reach stable operating temperature, which is crucial. Turn the temperature control knob to the heating side to activate the heat source, and warm air will naturally flow once the fan is operating. Depending on driving conditions, adjust the vent angles, such as prioritizing defrosting the windshield. During maintenance, ensure sufficient coolant to prevent pipe malfunctions that could affect heat transfer. Dual-zone climate control models offer greater flexibility, allowing separate temperature settings for left and right sides. Prioritize comfort during operation, and press the compressor button to save fuel consumption.
Was this review help?
15
5
Share
Expand All
More Forum Discussions

How is Tire Pressure Monitoring Achieved?

Tire pressure monitoring can be achieved through three methods: Direct Tire Pressure Monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire's air pressure. A wireless transmitter sends the pressure information from inside the tire to a central receiver module, which then displays the pressure data for each tire. The system automatically alerts when the tire pressure is too low or if there is a leak. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that wheel to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors tire pressure. Indirect tire pressure warning systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Tire Pressure Monitoring System (TPMS): This system combines the advantages of the two aforementioned systems. It is equipped with direct sensors in two diagonally opposite tires and includes a 4-wheel indirect system. Compared to using only a direct system, this hybrid system can reduce costs and overcome the limitation of indirect systems, which cannot detect when multiple tires simultaneously have low pressure. However, it still cannot provide real-time data on the actual pressure in all four tires as a direct system does.
13
1
Share

What Causes the ABS Pump Noise During Passat Lingyu Startup?

Passat Lingyu startup ABS pump noise may be caused by insufficient or damaged power steering pump fluid, ABS pump self-checking, or internal control short circuit in the ABS pump. Insufficient or damaged power steering pump fluid: When the power steering pump lacks fluid or is damaged, it can cause abnormal noise in the ABS pump during vehicle startup. It is recommended to check whether the power steering fluid is insufficient. If it is insufficient, replenish it; if not, it indicates that the power steering pump is damaged and needs to be repaired or replaced at a 4S shop. ABS pump self-checking: Every time the vehicle starts after the power is turned on, the ABS pump will operate to build system pressure and perform a self-check. The operating sound of the ABS pump at this time is a normal phenomenon. Internal control short circuit in the ABS pump: If the ABS pump keeps making noise, it may be due to an internal control short circuit. In this case, it is necessary to go to a 4S shop or a professional repair shop for maintenance.
9
1
Share

How Often Should Valve Stems Be Replaced?

Because valve stems are made of rubber material, they are inevitably prone to cracking, deformation, and loss of elasticity. During daily driving, rubber valve stems undergo various deformations as they swing back and forth due to centrifugal force, which undoubtedly accelerates their aging. The typical lifespan of such rubber valve stems is about three to five years, similar to that of tires. Therefore, when replacing tires, remember to replace the valve stems as well. Below is the replacement cycle for valve stems: 1. New valve stems must be installed when replacing tires. This is because valve stems are rubber products and are subject to aging cycles. Even if the valve stems appear fine at the time of tire replacement, they may age prematurely during the new tire's usage cycle, posing safety risks. 2. Tire valve stems are one-way valves (check valves) used for inflating or deflating gases or liquids in tires and for maintaining and detecting internal pressure. 3. For tube-type tires, they are installed on the inner tube, while for tubeless tires, they are mounted on the rim. 4. Based on structure, they can be divided into two types: rubber-metal valve stems and metal valve stems with rubber gaskets. The former is used for inner tubes of passenger car tires, while the latter is mainly used for inner tubes of truck tires. The internal structure of tubeless tire valve stems is the same as that of ordinary valve stems.
8
2
Share

How many liters of gear oil should be added to the manual transmission of the Volkswagen New Jetta?

Volkswagen New Jetta manual transmission requires approximately three liters of gear oil. Introduction to automotive gear oil: It is a high-viscosity lubricating oil specifically designed to protect power transmission components, typically accompanied by a strong sulfur odor. Vehicle gear oil is classified based on performance and viscosity. Currently, the American Petroleum Institute (API) performance classification and U.S. military gear oil specifications are widely adopted worldwide. Most manual transmission lubricants and differentials use quasi-hypoid gear oils. These contain extreme pressure (EP) additives and anti-wear additives to handle the action of hypoid bevel gears. Working conditions of gear oil: During operation, gear oil experiences continuous changes in gear contact surfaces, with temperatures rising moderately, typically ranging from 10-80°C. Additionally, gear oil is subjected to extremely high pressure. During gear transmission, the unit pressure at the meshing part of the teeth can reach (196-245)×10 kPa, while hypoid gears can withstand unit pressures of (294-392)×10 kPa. Moreover, gear oil operates under conditions of significant speed variations and frequent rotations, making it prone to being squeezed out from the gaps between teeth, resulting in semi-fluid friction.
1
0
Share

Where are the airbags located in the Geely Boyue Pro 2020 model?

In the Geely Boyue Pro, the driver's airbag is positioned at the center of the steering wheel. The front passenger frontal airbag is located within the dashboard on the passenger side. The front passenger seat side airbag is situated on the side of the seat back closest to the door. Airbag Composition: Primarily consists of airbag sensors, collision airbags, and electronic control units. The driver-side collision airbag is installed in the steering wheel; the passenger-side collision airbag is typically mounted on the dashboard. Airbag sensors are installed on the left, right, and center of the cabin partition; the central airbag sensor and airbag system are integrated with the electronic control unit. The airbag module mainly includes the airbag, gas generator, and igniter. The electronic control unit is used for data collection and processing, diagnosing the reliability of the airbag, ensuring timely ignition signal transmission when preset values are reached, and ensuring precise ignition timing to guarantee sufficient driving current for the gas generator. Function of Airbags: The primary role of airbags is to prevent injuries caused by collisions between passengers and interior components during a car crash, typically serving as a supplementary safety device to seat belts, with both working in tandem. The airbag system is a passive safety (see automotive safety performance) protection system that, when used in conjunction with seat belts, provides effective collision protection for passengers. In the event of a car collision, airbags can reduce head injury rates by 25% and facial injury rates by approximately 80%.
7
3
Share

Why does the X-Trail's air conditioner only blow air without cooling?

Here are the reasons and solutions for the X-Trail's air conditioner only blowing air without cooling: 1. Incorrect mode Solution: If your fan starts but the main unit doesn't cool, check if your remote is set to cooling mode. Simply adjust it to cooling mode. 2. Insufficient refrigerant Solution: If both fan and main unit start, check if the refrigerant is adequate. If not, recharge it. However, before recharging, check for refrigerant leaks and fix any found. 3. Compressor failure Solution: Check if your compressor is functioning. If not, seek professional assistance.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.