How to Turn on the Honda Civic Wiper?

2 Answers
MariaLynn
08/26/25 3:49am
To operate the Honda Civic wiper, follow these steps: The wiper control switch on the right side of the steering wheel can be turned clockwise to activate the rear wiper and counterclockwise to turn it off. Pressing the wiper control switch toward yourself will spray water for the front wiper, while pushing it toward the dashboard will spray water for the rear wiper. More details about the wiper switch functions are as follows: 1. OFF: This position stops the front wiper operation, effectively turning the wiper off. Rotate the switch to this position to deactivate the wiper. 2. INT: Auto-intermittent operation. Pull the lever down one notch to activate the wiper in intermittent mode. This setting requires manual reset and is suitable for light rain or snow. 3. LO: Continuous operation. Pull the lever down another notch to engage the wiper in continuous low-speed operation. This also requires manual reset and is ideal for heavier rain or snow. 4. HI: Continuous high-speed operation. Pull the lever all the way down to activate the wiper at high speed. Manual reset is needed, and this setting is best for heavy rainstorms. In extreme downpours, even the highest wiper speed may not be effective. The best approach is to turn on hazard lights, pull over, and wait for the rain to lessen before continuing.
Was this review help?
20
2
Share
DelElla
09/08/25 4:41am
When driving a Honda Civic, the wiper operation is quite straightforward, but it's important to follow the steps. The stalk on the right side of the steering wheel is key: a light upward push activates the first setting, usually the intermittent mode; pushing it further up engages the slow wiping speed; and pushing it all the way to the top sets the fast speed. To spray washer fluid, simply pull or push the stalk downward. In daily use, I make it a habit to regularly check the wiper blades for wear. If they don’t clean properly or make unusual noises, it might be time to replace them. Also, ensure the windshield is clean, as dirty glass can cause the wipers to scratch the surface. Additionally, during heavy rain, promptly turning on the wipers helps maintain clear visibility and prevents accidents. Don’t forget to refer to the owner’s manual for model-specific differences, as the design may vary slightly between different Civic model years.
Was this review help?
19
3
Share
Expand All
More Forum Discussions

What to Do After Failing Driving Test Subject 3 Five Times?

After failing Subject 3 of the driving test five times, the results of other subjects that have already been passed will become invalid, and the candidate needs to re-register and pay the fees. After registration and payment, follow the original appointment process to schedule the Subject 1 test. After passing Subject 1, proceed to schedule the Subject 2 test, and so on.
4
0
Share

What to Do If the BMW Handbrake Won't Release?

Check if the handbrake cable is stuck. If the handbrake won't release due to being stuck, try pulling it up harder first, then press the handbrake button and release the handbrake. Inspect the handbrake ratchet mechanism. If this mechanism is damaged, it will prevent the handbrake from releasing. The owner should drive the car to a 4S shop or repair shop for further inspection and repair.
8
2
Share

How to Check Vehicle Information If the Vehicle Is Not Yours?

Ordinary citizens do not have the right to check vehicles registered under someone else's name. If needed, you can only negotiate with the vehicle owner to obtain the necessary information for the query. With the owner's consent, use their information to log in to the Traffic Management 12123 website, locate the motor vehicle option, click the More button, and follow the prompts to proceed with the query.
20
4
Share

What is the fuel tank capacity of the Toyota Highlander?

Highlander fuel tank capacity is 72 liters. Method to check fuel tank capacity: Drive the car until the fuel gauge shows only one or two bars remaining, and there is a gas station nearby. You can drive until the fuel warning light comes on, then go to the gas station and ask the attendant to fill it up. This way, you can estimate the fuel tank capacity. Method to check remaining fuel: Check the fuel gauge, which indicates the amount of fuel left in the car's fuel tank. It can be either a pointer or a digital display. The low fuel warning light alerts when the fuel level drops below a certain point, indicating that you should refuel promptly.
9
4
Share

Does shifting to R gear and stalling harm an automatic transmission car?

Brief instances won't cause damage, but frequent or prolonged occurrences will. The R gear is the reverse gear used when backing up, but it should only be engaged when the vehicle is completely stationary. Shifting into R while the car is still moving slowly can severely damage the transmission. Here's an introduction to automatic transmission gears: 1. L gear: Low gear limits speed. When climbing slopes, this gear maintains high RPM at low gear. 2. S gear: Sport mode allows free gear shifting but delays shift timing, keeping the engine at high RPM for extended periods, enabling low-gear high-RPM driving. 3. D gear: Drive gear is used for normal forward movement. 4. N gear: Neutral is for temporary stops. 5. P gear: Park gear should be engaged when parking to activate the parking brake and prevent rolling.
17
2
Share

Is the Borgward BX7 engine an EA888?

Borgward BX7 uses an engine produced by Foton. The BX7's engine is not an EA888, but it incorporates many technologies from the Volkswagen EA888 engine. The Borgward BX7 is equipped with a 2.0L turbocharged engine across all models. The engine model is 4G20TI1, with a maximum horsepower of 224ps, a maximum power of 165kw, and a maximum torque of 300nm. For daily maintenance of the Borgward BX7 engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices in the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, with the selection standard not lower than the manufacturer's requirements; Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, its performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level; When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is clogged and oil cannot pass through the filter element, it may rupture the filter element or open the safety valve, allowing oil to bypass through the bypass valve, bringing contaminants back to the lubrication areas, accelerating engine wear and increasing internal pollution; Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder from component wear to form sludge. A small amount remains suspended in the oil, while a large amount precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear; Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the engine operates normally but also extends the overall lifespan of the radiator and engine.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.