How to Turn on the High Beam of the Sylphy?

How to Measure Engine Cylinder Pressure?

Engine cylinder pressure measurement method is: 1. Remove all spark plugs and reset the gauge to zero; 2. Start the engine, observe and record the first jump value indicated by the needle; 3. If uneven high and low readings occur during measurement, the lower value indicates the piston was not started at full intake and compression timing. Engine cylinder pressure requires proper cooling of the cylinder and cylinder head to ensure the inner surface operates normally under high temperatures. There are two cooling methods: water cooling and air cooling. Water-cooled engines have cooling water jackets around the cylinders and in the cylinder head, with interconnected cooling water passages between the cylinder block and cylinder head. The circulating coolant continuously removes heat to cool the cylinder and cylinder head.

6

5

Share

Does parking at an angle with one side higher than the other have any impact?

Parking at an angle with one side higher than the other does have an impact. Detailed explanations are as follows: 1. Damage to the vehicle: Parking with one side higher than the other can damage the car. 2. Tire aging: Long-term parking in this manner can cause uneven force distribution among the four tires, leading to stress concentration and accelerating the aging of the tires on the side with higher stress. 3. Alteration of vehicle alignment parameters: Parking at an angle causes the suspension system to experience stretching or compression due to stress concentration. Prolonged stretching and compression can result in irreversible plastic deformation of the suspension system, thereby changing the vehicle's alignment parameters.

17

4

Share

What is the Difference Between Electronic Fuel Injection and Direct Injection?

The difference between electronic fuel injection and direct injection lies in their definitions: Electronic fuel injection refers to the process in a gasoline engine where fuel is injected into the intake manifold, controlled by a specific timing sequence of commands from the control program, and executed by electronic injectors. Direct injection, on the other hand, is a technology that injects fuel directly into the cylinder to mix with the intake air. Electronic fuel injection represents a type of engine that significantly differs from carburetor engines, also varying in operational methods. A direct injection engine employs Gasoline Direct Injection (GDI) technology and is a subset of electronic fuel injection, fully termed as in-cylinder direct injection.

20

4

Share

What brand is arroad tire?

Currently, there is no brand named arroad, but there is farroad, which is a brand under Shandong Fengyuan Tire Manufacturing Co., Ltd. Tires are circular elastic rubber products assembled on various vehicles or machinery to roll on the ground. They are usually mounted on metal rims, supporting the vehicle body, cushioning external impacts, ensuring contact with the road surface, and maintaining the vehicle's driving performance. Tires are often used under complex and demanding conditions, enduring various deformations, loads, forces, and high and low temperatures during operation. Therefore, they must possess high load-bearing capacity, traction performance, and cushioning performance. Additionally, they are required to have high wear resistance and flex resistance, as well as low rolling resistance and heat generation.

8

1

Share

What are the reasons for the high fuel consumption of Changan CS35?

The reasons for the high fuel consumption of Changan CS35 are as follows: Engine carbon deposits: When the engine has carbon deposits and is not cleaned in time, the car's fuel consumption will increase. Spark plug failure: When the spark plug fails, the car's acceleration will slow down, thereby increasing fuel consumption. Abnormal tire pressure: When the tire pressure is abnormal, the impact on fuel consumption is immediate, as increased friction leads to higher fuel consumption. Poor fuel injector atomization: Poor fuel injector atomization can cause blockages, thereby increasing fuel consumption, and sensor failure can lead to continuous fuel injection, further increasing fuel consumption.

9

2

Share

Is There 98 Octane Gasoline?

Gasoline includes 98 octane gasoline, which has an octane rating equivalent to a mixture of 98% isooctane and 2% n-heptane. Different gasoline grades represent varying levels of fuel anti-knock performance, with higher octane numbers indicating better anti-knock properties. Introduction to 98 Octane Gasoline: This grade of gasoline can be produced by many domestic manufacturers, but it is not available at every gas station. Although relatively expensive, occasionally using it can provide benefits such as cleaning the fuel system. Introduction to Gasoline: Gasoline is a volatile and flammable liquid hydrocarbon mixture obtained from the distillation, cracking, or pyrolysis of petroleum. Its characteristics include volatility, stability, anti-knock performance, corrosiveness, and cleanliness.

2

0

Share

How to Turn on the High Beam of the Sylphy?

How to Measure Engine Cylinder Pressure?

Does parking at an angle with one side higher than the other have any impact?

What is the Difference Between Electronic Fuel Injection and Direct Injection?

What brand is arroad tire?

What are the reasons for the high fuel consumption of Changan CS35?

Is There 98 Octane Gasoline?

What does an exclamation mark inside a Skoda bulb mean?

Where is the gear shift in a Tesla?

What are the lubrication methods for an engine?

How to release the engine lock on the Ford Kuga?