How to Turn on the High Beam in a Santana?

1 Answers
VanIsabelle
07/29/25 7:38pm
The method to turn on the high beam in a Santana is: toggle the lever on the left side of the steering wheel, pushing it forward activates the high beam. Taking the 2021 Santana as an example, it belongs to the compact car category with the following dimensions: length 4475mm, width 1706mm, height 1469mm, wheelbase 2603mm, fuel tank capacity 52.8l, and curb weight 1120kg. The 2021 Santana features a MacPherson strut front suspension and a compound torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 112ps, maximum power of 82kw, and maximum torque of 145nm, paired with a 5-speed manual transmission.
Was this review help?
16
0
Share
More Forum Discussions

What are the hidden features of the 2013 Ecosport?

The 2013 Ecosport does not have any hidden features. The 2013 Ecosport is a compact SUV with the following dimensions: length 4280mm, width 1785mm, height 1638mm, wheelbase 2530mm, minimum ground clearance 172mm, and a curb weight of 1245kg. The 2013 Ecosport features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 110PS, a maximum torque of 140Nm, and a maximum power output of 81kW. It is paired with a 5-speed manual transmission.
13
3
Share

Introduction to the Interior Functions of the 2021 Lavida?

2021 Lavida interior functions include: door panel button functions, window lift functions, center console screen button functions, air conditioning button functions, and seat heating button functions. Taking the 2021 Lavida as an example, it belongs to the compact car category, with body dimensions of: length 4670mm, width 1806mm, height 1474mm, a wheelbase of 2688mm, a fuel tank capacity of 51 liters, and a trunk capacity of 510 liters. The 2021 Lavida is equipped with a 1.4T turbocharged engine, delivering a maximum horsepower of 150 PS, a maximum power of 110 kW, a maximum torque of 250 Nm, and is paired with a 7-speed dual-clutch transmission.
8
5
Share

What is the belt routing for the Audi A6L?

Adjust the belt tension to the appropriate level, then tighten the engine mounting screws and adjustment screws. Below are the detailed steps for the Audi A6 belt routing: Removing the Belt: Loosen the alternator. First, loosen the locking screw on the alternator's movable track, then loosen the upper mounting screw of the alternator, and finally loosen the alternator position adjustment screw. Remove the alternator belt, disconnect the ventilation valve assembly, remove the four cylinder high-voltage wires, remove the water pump pulley, remove the valve cover sub-assembly, remove the No. 2 timing chain or belt cover, remove the crankshaft gear or pulley cover sub-assembly. Set the No. 1 cylinder to top dead center/compression position, rotate the crankshaft pulley, and align the pulley groove with the timing mark 0 on the No. 1 timing belt cover. Check that the K mark on the crankshaft timing pulley aligns with the timing mark on the bearing cap. Remove the timing belt, then remove the bolt and the No. 1 timing belt idler sub-assembly. Installing the Belt: Inspect and install the No. 1 timing belt idler sub-assembly, inspect and install the idler tension spring, install the tension spring, push the idler as close as possible to the water pump pulley and tighten the bolt. Position the No. 1 cylinder at top dead center of the compression stroke, rotate the hexagonal part of the camshaft to align the K mark on the camshaft timing pulley with the timing mark on the bearing cap. Use the crankshaft pulley bolt to rotate the crankshaft and align the timing marks on the crankshaft timing pulley and the oil pump. Install the timing belt and check the belt deflection.
18
2
Share

Should You Turn on Hazard Lights During Heavy Rainstorms?

During heavy rainstorms, it is advisable to turn on the hazard lights. The correct method to activate hazard lights is to press the red triangle button located on the vehicle's dashboard. The purposes of hazard lights are: 1. To alert other vehicles in case of breakdowns, accidents, or emergencies; 2. To prevent rear-end collisions when parking on the roadside. Situations where hazard lights should be used include: 1. Vehicle breakdown or traffic accident on the road; 2. Parking on the roadside; 3. Driving in foggy conditions; 4. When towing a malfunctioning vehicle, both the towing vehicle and the towed vehicle should turn on hazard lights; 5. Temporary parking on the road; 6. Visibility less than 100 meters; 7. Transporting critically ill patients; 8. Reversing or making U-turns on complex road sections.
10
0
Share

What is the license plate prefix for Dujiangyan?

Dujiangyan license plates start with Chuan U. A license plate refers to the vehicle registration plate, which is a metal or plastic plate attached to the front and rear of a vehicle. The materials used include aluminum, sheet metal, plastic, or paper, and they display the vehicle's registration number, registration region, and other relevant information. The first character on the license plate is a Chinese character representing the abbreviated name of the province where the vehicle is registered. The second character is an English letter, indicating the prefecture-level city code where the vehicle is registered, followed by a five-digit serial number. The functions of license plates are: 1. To assign numbers and register information for each vehicle; 2. To identify the region where the vehicle is registered; 3. To trace the owner and registration details of the vehicle based on the license plate.
8
3
Share

What to Do When the General Fault Indicator Light Is On?

Solutions for when the general fault indicator light is on are: 1. Check all the bulbs in the car to identify the damaged one; 2. Replace the damaged bulb. Hazards of the fault light being on include: 1. The quality of the car's exhaust emissions deteriorates, polluting the environment; 2. Increased combustion chamber temperature and accelerated wear, leading to engine damage; 3. Causes the engine to burn oil; 4. Increased engine noise, affecting driving and passenger comfort. Reasons for the fault light being on are: 1. Ground adhesion control system malfunction; 2. Excessive tire pressure or tire leakage; 3. Driving with low tire pressure for too long; 4. Faulty tire pressure sensor; 5. Automatic transmission damage.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.