How to Turn On the High and Low Beams on a Mazda6?

1 Answers
JoannaFitz
07/29/25 5:37pm
To operate the high and low beams on a Mazda6: First, turn on the headlight switch. The lever for switching between high and low beams is located under the steering wheel, on the same stalk as the turn signal. To change the beams, move the lever up and down: pushing it downward activates the high beams, pulling it upward switches to low beams, and lifting it up briefly flashes the high beams (returning to low beams when released). Note that the Mazda6's left headlight is slightly lower than the right one. Both high and low beams are not parallel but form a "seagull" pattern. Additionally, the headlight brightness is intentionally dimmer compared to other models to prevent dazzling oncoming drivers during encounters, reducing potential accident risks. The Mazda6 is a midsize sedan with the following dimensions: Length: 4670mm, Width: 1780mm, Height: 1435mm, Wheelbase: 2675mm.
Was this review help?
1
3
Share
More Forum Discussions

What are the body dimensions of the Tharu?

The Tharu has a length of 4453 mm, a width of 1841 mm, a height of 1632 mm, and a wheelbase of 2680 mm. Below is some related information about the Tharu: 1. The Tharu is a compact SUV under the Volkswagen brand. The exterior and interior design of this car are both very attractive. Despite being a compact SUV, the interior space is not small. 2. The Tharu is equipped with two engines: one is a 1.4-liter turbocharged engine, and the other is a 2.0-liter turbocharged engine. 3. The 1.4-liter turbocharged engine, coded as EA211-DJS, has a maximum power of 110 kW, a maximum torque of 250 Nm, a maximum power speed of 5000 rpm, and a maximum torque range of 1750 to 3000 rpm. This engine features direct injection technology and uses an aluminum alloy cylinder head and block. 4. The 2.0-liter turbocharged engine, coded as EA888-DKV, has a maximum power of 137 kW, a maximum torque of 320 Nm, a maximum power speed range of 4100 to 6000 rpm, and a maximum torque range of 1500 to 4000 rpm. This engine is equipped with combined injection technology and uses an aluminum alloy cylinder head and a cast iron cylinder block.
4
3
Share

How many liters of oil can be added to the Sagitar 1.4T?

The recommended engine oil capacity is approximately 4L. After adding oil, check the oil dipstick scale for the exact level. Below are relevant details: 1. This engine is turbocharged, so it requires full synthetic oil due to the high temperatures and rotational speeds during turbocharger operation, which demand superior lubrication. 2. After adding oil, start the vehicle and check the level 3 minutes after turning off the engine. This is because the oil filter needs replacement during an oil change, and the new filter initially contains no oil. Starting the vehicle allows oil to flow into the filter. Waiting 3 minutes ensures oil returns to the oil pan for an accurate measurement. 3. Never check the oil level on a slope, as vehicle tilt causes uneven oil distribution in the oil pan, leading to inaccurate readings.
8
1
Share

What is Backfire?

Backfire refers to the phenomenon where the mixture of air and fuel gas forms a negative pressure when the flow velocity from the gas nozzle is lower than the flame propagation speed, causing the flame to retreat into the burner for combustion. The following is an introduction to backfire: 1. To prevent backfire, it is necessary to overcome factors that can increase the flame propagation speed or reduce the ejection velocity of the mixture. 2. Engine backfire means that the fuel mixture ignites outside the combustion chamber before entering it. 3. This situation is generally caused by incorrect engine ignition timing, poor engine operating conditions leading to excessively high cylinder temperatures, or poor valve sealing.
20
5
Share

Where is the battery located in a Cadillac?

The battery in a Cadillac is located on the left side of the trunk. After opening the trunk lid, remove the left interior panel to access the battery. Below is some relevant information about Cadillac batteries: 1. Placing the battery in the trunk helps balance the front and rear weight distribution of the vehicle, which is beneficial for driving. 2. When replacing the battery, first ensure the car is turned off with all electrical devices switched off. Next, disconnect the negative and positive battery cables, remove the battery mounting hardware, and take out the old battery. Then, clean the connection points between the battery terminals and cables before installing the new battery. Secure the battery mounting hardware and finally tighten the positive and negative battery cables.
13
0
Share

How long does it take to drive away after car painting?

After painting, you need to wait at least 24 hours before driving away. When painting a car, it is essential to go to a professional institution and seek experts. Car paint is relatively complex, consisting of four layers from the inside out: the electrophoretic layer, the primer layer, the base coat, and the clear coat. Here is an introduction to each layer of car paint: 1. Electrophoretic layer: After the entire car body is assembled, it is generally immersed in an electrophoretic tank, forming an electrophoretic layer on the surface of the car body. 2. Primer layer: After the electrophoretic layer is formed on the car body surface, robots spray the primer layer, which also plays a crucial role in rust prevention and enhances the adhesion with the next layer of car paint. 3. Base coat: Above the primer layer is the base coat, which primarily serves an aesthetic purpose. The various colors of car paint visible are essentially presented by the base coat. 4. Clear coat: The clear coat protects the base coat and enhances the glossiness of the car paint.
11
5
Share

When is the Right Time to Add Antifreeze?

Vehicle antifreeze generally needs to be replaced every 2 years or 40,000 kilometers. This is just a reference interval. For commercial vehicles with higher mileage, the replacement cycle should be shorter. Since driving conditions vary for each vehicle, the replacement should be based on actual usage. Check the antifreeze level regularly, and top it up promptly if it's insufficient. If suspended particles, sediment, or signs of deterioration or discoloration are observed in the antifreeze, it should be replaced immediately, and the system should be cleaned. Types of Antifreeze: Antifreeze is generally categorized into three types: ethanol-water, glycerol-water, and ethylene glycol-water. How to Choose Antifreeze: The key indicators for antifreeze are its freezing point and boiling point. Available antifreeze products on the market come with freezing points of -15°C, -25°C, -30°C, -40°C, etc. It is advisable to choose an antifreeze with a freezing point at least 10°C lower than the lowest temperature in your region. Functions of Antifreeze: Antifreeze is non-corrosive and is a coolant containing special additives, primarily used in liquid-cooled engine cooling systems. It offers excellent performance in preventing freezing in winter, boiling in summer, and protecting against scale and corrosion throughout the year.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.