How to turn on the heating in Haval F7?

2 Answers
MacChristian
07/24/25 3:45pm
Haval F7's heating switch is the small fan button on the center console. The method to turn on the heating is: 1. First press the air conditioning button (small fan button) to turn on the air conditioning; 2. Then turn off the AC switch (cooling switch), and adjust the temperature higher to get warm air. Haval F7 air conditioning button introduction: 1. ON button: Press this button, the corresponding indicator light will turn on, indicating that the air conditioning system is activated. When the air conditioning is on, pressing this button can adjust the air conditioning settings interface. 2. OFF button: Can turn off the air conditioning system. 3. A/C button: After the compressor is turned on, it can lower the temperature and humidity inside the car. 4. Auto mode button: Press until the corresponding indicator light turns on, indicating that the auto mode is activated. Adjust the temperature to the desired level, and the air conditioning system will automatically adjust the airflow mode and volume to reach the set temperature.
Was this review help?
18
1
Share
LaWyatt
08/11/25 8:46am
Turning on the heater in my Haval F7 is quite simple: First, start the engine and let it warm up for a minute or two to make hot air come out more easily. On the air conditioning panel, there's a temperature knob—I just turn it to the right into the red marked zone or set the value above 25°C; if it's in automatic mode, pressing the AUTO button will automatically control the temperature and fan speed. I also adjust the fan speed appropriately, not too strong to avoid noise that might disturb driving. I pay attention to switching between recirculation and fresh air modes—on cold days, I first use fresh air mode to expel cold air, then switch to recirculation to heat the cabin space faster. If the heater still doesn’t feel warm after turning it on, it might be due to low engine temperature or a cooling system issue. I wait until the car has been driven for a while before checking if the settings are correct. This method helps me save time and drive safely.
Was this review help?
19
4
Share
Expand All
More Forum Discussions

What is the reason for the noise when releasing the throttle in neutral on the Baojun 730?

Baojun 730 makes a noise when releasing the throttle in neutral because the speed and gear are not properly matched. The matching between gears and speeds is as follows: First gear is for starting, with a speed generally between 0-5km/h; second gear corresponds to speeds of 5-20km/h; third gear corresponds to speeds of 20-40km/h; fourth gear corresponds to speeds of 40-60km/h; fifth gear corresponds to speeds of 60-100km/h. Sixth gear is for speeds between 100-120km/h. Timing for upshifting: When the engine has ample power, it emits a dull "humming" sound. If after upshifting there is no sign of insufficient power or shaking of the transmission mechanism, and the speed increases quickly with smooth and natural vehicle movement, it indicates the upshifting timing is accurate.
8
1
Share

Is the Jade Glaze White of Haval H6 the same as Pearl White?

Haval H6's Jade Glaze White is not Pearl White. Definition of car paint: Automotive paint refers to the paint sprayed on cars, which is a type of coating. Function of car paint: Applying paint to a car not only forms a protective film on the surface, making the body less susceptible to corrosion and extending the vehicle's lifespan, but also provides an aesthetically pleasing experience. Different automotive paints produce different effects. Choosing different types of paint and colors can showcase the unique personality of the car. Therefore, automotive paint is crucial to the car itself.
15
3
Share

Where is the crankshaft position sensor on the Haval H9?

The crankshaft position sensor is located near the large flywheel at the front or rear end of the vehicle's crankshaft, or in the middle of the crankshaft. Introduction to the crankshaft position sensor: The crankshaft position sensor is usually installed at the front end of the crankshaft (near the pulley), near the large flywheel at the rear end of the crankshaft, or in the middle of the crankshaft. In early models, it was also installed inside the distributor. It is one of the most important sensors in the control system. Function of the crankshaft position sensor: It detects the engine speed, hence it is also known as the speed sensor; it detects the top dead center position of the piston, so it is also called the top dead center sensor, including detecting the top dead center signals of each cylinder for ignition control and the top dead center signal of the first cylinder for sequential fuel injection control.
19
4
Share

How to Distinguish Whether the Inspire Meets China 5 or China 6 Emission Standards?

Distinguishing whether the Inspire meets China 5 or China 6 emission standards can be done through the vehicle's compliance certificate. The main differences between China 5 and China 6 standards are as follows: Different Labels: The simplest and most direct method is to check the vehicle's environmental protection label, which has clear markings on the back. For new vehicles, you can check the vehicle's factory compliance certificate. Alternatively, you can visit the Motor Vehicle Environmental Protection website and enter the vehicle's VIN number and the last six digits of the engine number to query the information. Different Emission Standards: The China 6 emission standard is the sixth stage of national motor vehicle pollutant emission standards. The China 5 emission standard, also known as "China 5," has emission control levels equivalent to the European Union's currently implemented Euro 5 emission standards.
16
4
Share

Does the Baojun 510 have ISOFIX interfaces?

Baojun 510 has ISOFIX interfaces. The function of ISOFIX interfaces: ISOFIX interfaces can firmly connect child car safety seats to the vehicle, providing a simpler and safer method for installing car seats. Installing seats using ISOFIX is easier than using seat belts and can effectively reduce the risk of incorrect installation, significantly lowering the chance of errors. Other interfaces: In addition to the ISOFIX interface for securing child seats, there are also the LATCH system following the American standard and the seat belt securing method. The location of the LATCH interface varies depending on the vehicle model; for sedans, it is usually behind the rear seat headrests, while for hatchbacks, it is typically on the back of the rear seats.
6
0
Share

What is the Audi model fv7148fadbg?

The vehicle model Audi fv7148fadbg is a low-end version of the Audi A4L produced by FAW-Audi, equipped with a 1.4T turbocharged engine. Below is an introduction to the Audi A4L: Overview: The Audi A4L is a model officially released by Audi on November 16, 2008. The new Audi A4L features a completely new exterior and chassis design, with the front and rear resembling the Audi A5. It boasts a stylish and dynamic appearance with smooth lines; the interior is exquisitely crafted, offering spacious and practical space, embodying the classic brand. Model Introduction: Many components of the redesigned chassis are made of aluminum, enhancing the chassis strength while reducing its weight. The rear features smooth, full, and rounded lines, with a slightly upward design on the trunk lid that helps stabilize the airflow at the rear during high-speed driving.
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.