How to Turn on the Headlights of a Tiida?

1 Answers
LeTucker
07/29/25 5:05pm
Here is how to turn on the headlights of a Tiida: 1. The light assembly is located on the lever behind the steering wheel on the left side. 2. Turn the lever forward three times to the left, and the headlights will turn on. 3. Push the lever slightly downward for high beams, and pull it back for low beams. Below is some related information on using the Tiida headlights: 1. When meeting another vehicle at night, switch to low beams when the oncoming vehicle is more than 150 meters away. 2. Use low beams when meeting non-motorized vehicles on narrow roads or bridges at night. 3. When passing through an intersection controlled by traffic lights at night, use low beams when turning. 4. Use low beams when driving close to the vehicle in front of you in the same direction.
Was this review help?
6
1
Share
More Forum Discussions

What is the ground clearance of the Lavida?

The minimum ground clearance of the Lavida is 110 millimeters. Relevant details are as follows: 1. The 110 millimeters refers to the minimum ground clearance of the Volkswagen Lavida when fully loaded, which is the smallest distance between the lowest point of the Lavida's body (excluding the wheels) and the ground. 2. The minimum ground clearance of a car reflects its performance in navigating complex road conditions. The greater the ground clearance, the stronger the car's ability to overcome obstacles. Below is additional information: The impact of a car's minimum ground clearance on driving is as follows: 1. The smaller the ground clearance, the weaker the ability to overcome obstacles. Sedans generally travel on flat urban roads, so they have smaller ground clearances. Off-road vehicles have larger minimum ground clearances to allow them to overcome larger obstacles. 2. The larger the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven ground, but a higher center of gravity reduces stability. The smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven ground, but a lower center of gravity increases stability.
15
5
Share

What should be noted when using seat belts?

Precautions for using seat belts include: 1. Each time you use a seat belt, check the label and certification, inspect the nylon belt for cracks, ensure the stitching is secure, and check the metal parts for missing, cracks, or rust. The safety rope should be used by hanging it on the connecting ring. 2. Seat belts should be hung high and used low, avoiding swinging, collisions, and sharp objects, and should not come into contact with open flames. 3. During operation, securely fasten the hooks and rings of the seat belt to the anchoring points. 4. When using seat belts in low-temperature environments, take care to prevent the belt from hardening and splitting. 5. Frequently used safety ropes should be regularly inspected for appearance. If abnormalities are found, replace the rope immediately and pay attention to adding a rope sleeve. 6. Do not tie knots in the seat belt, as this may cause the safety rope to break at the knot during an impact. Instead, attach the safety hook to the connecting ring, not directly to the safety rope, to prevent the rope from being cut during a fall. 7. After two years of use, seat belts should be batch-tested based on purchase conditions. The waist belt should undergo static load testing, and the safety rope should undergo impact testing. If no breakage occurs, they can continue to be used. Defective items should not be used further. Safety ropes that have been sampled must be replaced before use, and a rope sleeve should be added when replacing the rope. 8. Seat belts should be stored in a dry, ventilated warehouse, away from high temperatures, open flames, strong acids, strong alkalis, and sharp hard objects. They should also not be exposed to direct sunlight. When moving, avoid using tools with hooks or spikes, and protect them from sun and rain during transportation. 9. Seat belts should be cleaned regularly. They can be gently wiped with soapy water in warm water, rinsed with clean water, and then air-dried. 10. Do not remove any components from the seat belt arbitrarily. When replacing parts, choose qualified accessories. 11. The service life of a seat belt is 3-5 years. If abnormalities are detected, it should be scrapped early. During use, inspect it regularly and test it every six months to a year. The main components should remain undamaged. If any damage or deterioration is found, report it immediately and stop using the belt to ensure operational safety.
17
5
Share

How to Maintain a Car That Hasn't Been Used for a Long Time?

Maintenance methods for a car that hasn't been used for a long time: 1. If the car is not used for an extended period, it is recommended to start the vehicle every one or two weeks. If possible, drive the car a short distance to prevent engine issues. 2. Cover the vehicle with a car cover and park it in a garage, or park it on a flat surface away from direct sunlight to prevent damage to the paint or leakage of vehicle fluids. 3. Before leaving the car unused for a long time, clean the exterior and interior of the vehicle. Dirt on the car's paint that is not cleaned for a long time can damage the paint. 4. Keep the battery fully charged. The battery undergoes natural discharge, and if the car is not used for a long time, starting it may become difficult. Regularly inspect and maintain the car battery to prevent it from losing charge.
3
5
Share

Where to Check Vehicle Emission Standards?

Methods to check vehicle emission standards: 1. Look for the environmental compliance label sticker on the front windshield; 2. Check the emission standard description in the vehicle purchase documents; 3. Search for the vehicle's emission standard on professional websites online; 4. Take the vehicle registration certificate to the local DMV for inquiry. Vehicle emission standards refer to regulations on the content of harmful gases such as CO, HCNOx, and PM emitted from vehicle exhaust. Exhaust contains 150 to 200 different compounds, and since vehicle emissions are released within 2 meters, which is within the human breathing range, they pose significant health risks.
3
3
Share

How to Connect Car Bluetooth?

Steps to connect car Bluetooth: 1. First, turn on the Bluetooth switches of both the car Bluetooth and your mobile device; 2. Then, in your phone's Bluetooth settings, press 'Search for New Device' and click to connect when the car Bluetooth name appears; 3. Finally, during the pairing process, you will need to enter the car Bluetooth's pairing code, after which the connection will be successful. If the Bluetooth connection fails, it may be due to compatibility issues between your phone's system and the Bluetooth system, requiring you to update your phone's system. Additionally, during the connection process, you should not be too far from the car Bluetooth, as this can also affect the Bluetooth pairing. Moreover, when high-power electrical appliances are near the display or the phone is covered by metal materials, the Bluetooth pairing can easily be interrupted.
15
0
Share

How to Determine if the Charcoal Canister is Clogged?

Methods to determine if the charcoal canister is clogged: 1. After driving the car for a certain distance, stop and keep the engine running. Open the fuel filler cap and listen for a suction sound; if present, it indicates a clogged charcoal canister. 2. Notice a strong gasoline odor in the car. 3. After leaving the car parked outdoors for an extended period, open the fuel tank cap and observe if a large amount of gas is expelled outward. If so, it indicates a clogged charcoal canister. The charcoal canister is part of the gasoline evaporation control system, installed between the fuel tank and the engine. Its function is to direct gasoline vapor into the combustion process to prevent it from evaporating into the atmosphere, aiming to save fuel and protect the environment. If the charcoal canister becomes clogged, it should be cleaned or replaced promptly.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.