How to turn on the front fog lights of the Bora?

1 Answers
McAdelyn
07/29/25 9:38pm
Volkswagen Bora's fog light switch is located on the inner side of the control lever and is operated by rotation. Turn it upwards once to turn on the front fog lights, and turn it twice to the rear fog light position, which simultaneously turns on both front and rear fog lights. Conversely, turn it back to turn them off. Here is an introduction to fog lights: Introduction to fog lights: Fog lights generally refer to automotive fog lights. Automotive fog lights are installed at the front and rear of the vehicle and are used to illuminate the road and provide safety warnings when driving in rainy or foggy weather. They improve the visibility of the driver and surrounding traffic participants. Precautions for using fog lights: Do not use fog lights when driving at night without fog, as the front fog lights have no light shield and the rear fog light bulbs have high power, which can create dazzling brightness for oncoming drivers and those following behind, further affecting driving safety.
Was this review help?
6
5
Share
More Forum Discussions

What engine does Baojun use?

Baojun uses a 1.5L naturally aspirated engine. Naturally aspirated engine: It is a type of automobile air intake, where atmospheric pressure forces air into the combustion chamber without any supercharger. Working principle of naturally aspirated engine: The naturally aspirated type has no supercharger, meaning air simply passes through the air filter, throttle, intake manifold to reach the cylinder, and gasoline is directly injected into the intake manifold through the fuel injector. Advantages of naturally aspirated engine: In terms of smoothness in power output and directness in response, naturally aspirated engines are far superior to supercharged engines. The current V8 2.4L F1 engine is the best example.
6
1
Share

Is driving at 85 in an 80 km/h average speed zone considered speeding?

Speeding. Below are the relevant details: 1. Average speed measurement: This refers to the method of detecting the average speed of a motor vehicle passing through a section of road (speed measurement zone) between two adjacent speed monitoring points. For example, if the distance of a speed measurement zone on a highway is 10 kilometers with a speed limit of 120 km/h, a vehicle that takes 5 minutes or more to complete the distance would have an average speed below 120 km/h, meeting the speed limit requirement; if it takes less than 5 minutes to pass through the zone, it would be speeding. 2. Penalties for speeding in highway average speed zones are as follows: A warning is issued for speeding less than 10% on highways or national roads, with no points deducted or fines imposed; for speeding between 10% and 20%, 3 points are deducted and a fine of 200 yuan is imposed.
9
0
Share

What are the reasons for the large injection pulse width of the Bora Classic?

Bora Classic injection pulse width is too large for the following reasons: Observe with idle speed: If the injection pulse width is too large, it is generally necessary to observe it in conjunction with the idle speed. If the idle speed is high and the pulse width is large, it is usually caused by false signals from the throttle position sensor or coolant temperature sensor. If the idle speed is normal, then the oxygen sensor is likely to be faulty. Caused by inaccurate closed-loop data: Inaccurate closed-loop data received by the ECU can also lead to this issue. Among these data, the oxygen sensor and coolant temperature sensor are the primary factors, though the intake pressure sensor and throttle position sensor should not be ruled out. Use a Bluetooth OBD scanner to identify the source of the problem.
10
0
Share

Is Subject 2 or Subject 3 Harder to Schedule?

Subject 3 is more difficult to schedule. Here is more information about the Subject 3 test: 1. Content of the Subject 3 test: The road driving skills test for Subject 3 generally includes: preparation before getting in the car, simulated lighting test, starting, driving straight, shifting gears, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and nighttime driving. 2. Notes for the Subject 3 test: Stay calm during the test. When shifting gears and operating lights, do not let nervousness affect your performance, and avoid losing points on the simplest procedures. Practice is key to passing the Subject 3 test. Observe carefully during practice, and be able to handle unexpected situations flexibly, ensuring a flawless performance during the actual test.
17
4
Share

What are the reasons for the no signal issue in Bestune T77's vehicle networking?

The possible reasons for the no signal issue in Bestune T77's vehicle networking could be signal interference around the vehicle or a malfunction in the vehicle networking antenna. Solutions for the no signal issue in vehicle networking: Replace the radio head, install an external antenna or signal amplifier. Installing an external antenna or signal amplifier can be effective for your car, as it is not only relatively simple to install but also cost-effective. Alternatively, installing a signal amplifier can help, as the original factory navigation system usually comes with a built-in signal amplifier. Introduction to vehicle networking: Vehicle networking is an interactive wireless network built based on information such as vehicle location, speed, and route. It ensures the distance between vehicles, reducing the likelihood of collisions. Vehicle networking also helps drivers with real-time navigation and improves traffic efficiency by communicating with other vehicles and network systems.
5
3
Share

Should I Still Go to Sign if I Failed the Third Driving Test?

After completing the road test, regardless of whether the result is pass or fail, the candidate is required to sign to confirm their own score. Below are specific explanations regarding the third driving test: 1. Definition: The third test, also known as the road test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safe civilized driving knowledge test in the motor vehicle driver's examination. 2. Test Instructions: If the fifth scheduled test is still failed within the validity period of the driving skill test permit, the results of other previously passed subjects will be invalidated. 3. Test Content: The third test generally includes: vehicle preparation, light simulation test, starting, driving straight, gear shifting operation, lane changing, parking by the roadside, going straight through intersections, turning at intersections, meeting vehicles, overtaking, making U-turns, and night driving.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.