How to Turn on the Fog Lights on the Geely Xingrui?

2 Answers
LeKyle
07/25/25 9:17am
The fog lights of the vehicle are adjusted on the light control lever, which is located on the left side of the steering wheel. The "OFF" position turns off the rear fog lights of the vehicle. Turning the middle knob counterclockwise by one position turns on the rear fog lights. When using the vehicle's lights, pay attention to the dashboard indicator lights. When using the fog lights, ensure they are combined with the vehicle's parking lights or automatic lights. During heavy rain, fog, or when visibility is less than 200 meters, the fog lights should be turned on.
Was this review help?
10
3
Share
VonTalia
08/11/25 7:16pm
I remember that turning on the fog lights was a routine operation when driving the Geely Xingrui. First, start the vehicle's engine to ensure the system is powered. There's a knob on the left-side lighting control lever near the steering wheel, typically featuring various light icons: first, turn it counterclockwise to the position light (position) and then to the fog light position (the icon looks like two horizontal bars or is labeled 'FOG'). If it doesn't light up, check whether the vehicle is in driving mode or if the fog light switch button is activated—some models require an additional button. In heavy fog, turning them on promptly can improve visibility; I once safely navigated through dense mountain fog using this method. Remember to use them only when visibility is below 100 meters to avoid dazzling other drivers in normal weather. During regular maintenance, ask the technician to check the fog light circuit and bulbs to prevent malfunctions—this habit makes driving safer.
Was this review help?
7
4
Share
Expand All
More Forum Discussions

When to Use the Width Indicator Lights?

Width indicator lights are used during dawn, dusk, and rainy or overcast weather. Here is an introduction to width indicator lights: 1. Width indicator lights are warning lights on vehicles, primarily used in low visibility conditions to alert other vehicles. 2. Since the width indicator lights also turn on when the headlights are activated, many drivers do not have the habit of manually turning them on during daily driving. 3. In hazy weather, during evening drives, or in light rain, the width indicator lights can be turned on independently without the need to activate the low beam headlights (as low beams are not very noticeable during the day), making it easier for vehicles in front and behind to identify your car.
12
2
Share

How to Replace the Oil Filter?

Replacing the oil filter involves the following steps: 1. Loosen the oil filter using a specialized wrench (turn counterclockwise). 2. When installing, apply a small amount of oil to the rubber gasket of the new oil filter, then screw on the new oil filter. 3. Add engine oil, then close the oil filler cap, and start the engine to check for any leaks at the oil filter and drain plug. Below is relevant information about oil filters: The function of an oil filter: It is used to remove impurities such as dust, metal particles, carbon deposits, and soot from the engine oil. Classification of oil filters: Full-flow and bypass types.
15
5
Share

Reasons for the Airbag Light to Illuminate

The main reasons and solutions for the airbag light to illuminate are as follows: 1. Loose or disconnected wiring. Solution: Inspect the airbag wiring. 2. Faulty airbag sensor. Solution: Replace the driver-side side airbag sensor. 3. Airbag malfunction. Solution: Check the seat belt sensor, airbag connector, and airbag sensor. 4. Faulty airbag control unit. Solution: Replace the airbag control unit. 5. Presence of fault codes. Solution: Use specialized equipment to clear the fault codes. 6. The light may illuminate during engine self-test and turn off after the self-test is completed, which is a normal phenomenon.
11
0
Share

Where is the computer port located in the Ford Escort?

The computer interface of the Escort is located at the lower left corner of the plastic cover under the steering wheel. The OBD (On-Board Diagnostics) system serves as a bridge connecting the computer to the vehicle's diagnostic system. Here is some information about OBD: 1. Originally designed as a system to monitor exhaust emissions, OBD has gradually expanded its control scope over time. With the advancement of vehicle sensors and electronic systems, OBD now encompasses a wide range of monitoring functions. 2. The OBD interface, as the communication port for the vehicle monitoring system, not only reads fault codes for repairs but also provides various operational data of the vehicle. Beyond the data displayed on the vehicle dashboard, the actual data recorded by the onboard computer is much more extensive.
5
3
Share

Symptoms of a Bad Front Wheel Bearing in a Car

Signs of a damaged front wheel bearing in a car are as follows: 1. Driving noise: Noise is the most prominent sign of a damaged wheel bearing. The symptom is a continuous noise emitted during vehicle operation. 2. Steering wheel vibration: If the front wheel bearing is severely damaged, causing increased bearing clearance, the steering wheel may vibrate while driving. 3. Unstable driving: When the front wheel bearing is excessively damaged, it can cause body vibration and unstable driving at high speeds. Solution: Wheel bearings are non-repairable components and require replacement.
17
5
Share

Can You Wax a Car with Paint Protection Film?

Yes, you can wax it. Here are some relevant points about waxing: 1. The purpose of waxing is to protect against acid rain and dust. While paint protection film is durable, accumulated dirt can accelerate its corrosion. If you neglect the maintenance of the film, such as not washing the car regularly, the brightening effect of the film will diminish, its lifespan will shorten, and it will lose its optimal aesthetic appeal. 2. Paint protection film inherently has better corrosion resistance than wax, but nothing is completely immune to corrosion, including the film. Acid rain, insect remains, bird droppings, and accumulated dirt can gradually erode the film, affecting the car's surface shine. Therefore, keeping the film clean is crucial. 3. Do not wax the film within the first three days after application, and never polish it, as this can cause irreversible damage. After that, waxing every two months is generally sufficient to keep the film's surface shiny and new for a long time.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.