How to Turn on the Fog Lights of Geely Boyue?

1 Answers
LaEloise
07/30/25 2:38am
Fog lights can be turned on by pulling the fog light gear control lever. Here is the relevant introduction about fog lights: 1. The fog light switch is located on the light control lever on the left side of the vehicle. Open the car door to see the fog light gear control lever. The prerequisite for turning on the fog lights is to turn on the width lights or headlights. 2. Fog lights generally refer to automotive fog lights. Automotive fog lights are installed on the front and rear of the vehicle and are used to illuminate the road and provide safety warnings during rainy or foggy weather. They improve the visibility of the driver and surrounding traffic participants. 3. Rear fog lights refer to red signal lights installed at the rear of the vehicle in environments with low visibility such as fog, rain, or dust, making it easier for other road traffic participants behind the vehicle to detect the vehicle. These lights have greater luminous intensity than tail lights. 4. Front fog lights are installed at a position slightly lower than the headlights at the front of the vehicle and are used to illuminate the road during rainy or foggy weather. Because visibility is low in foggy conditions, the driver's line of sight is limited. The lights can increase the running distance, especially the strong light penetration of yellow anti-fog lights, which can improve the visibility of the driver and surrounding traffic participants, allowing oncoming vehicles and pedestrians to detect each other from a greater distance.
Was this review help?
3
5
Share
More Forum Discussions

What is the minimum ground clearance of the Geely Boyue?

Geely Boyue's minimum ground clearance is 170 millimeters. Minimum ground clearance refers to the distance between the lowest point of the vehicle (excluding wheels) and the supporting surface when the car is fully loaded and stationary, which is used to characterize the vehicle's ability to pass over obstacles such as stones and tree stumps without collision. The Geely Boyue is a compact SUV with body dimensions of 4519 mm in length, 1831 mm in width, and 1694 mm in height, a wheelbase of 2670 mm, and a fuel tank capacity of 58 liters. The Geely Boyue is equipped with a 1.8T turbocharged engine, with a maximum power of 120 kilowatts, a maximum power speed of 5500 rpm, a maximum torque of 250 Newton-meters, and a maximum torque speed range of 1500 to 4500 rpm.
8
2
Share

Why is hot air blowing from the vents when the car air conditioner is off?

The reasons why hot air blows from the vents when the car air conditioner is off are: 1. The external circulation is turned on; 2. The AC button is activated; 3. Lack of refrigerant; 4. Compressor slippage or looseness; 5. Dirty air filter; 6. Controller malfunction; 7. Blocked radiator or condenser; 8. Faulty wiring from the controller to the air conditioner. The solutions to fix hot air blowing from the car air conditioner are: 1. Turn off external circulation; 2. Deactivate the AC button; 3. Refill refrigerant; 4. Adjust the compressor position; 5. Clean the air filter; 6. Replace the controller; 7. Clean the radiator and condenser; 8. Replace the wiring from the controller to the air conditioner.
18
3
Share

How to Spray Windshield Washer Fluid on Lavida?

Lavida sprays windshield washer fluid by: Simply turn the ignition switch to the ON position, then slightly lift the wiper control lever on the right side of the steering wheel to activate the spray. When the transparency of the front windshield deteriorates, spraying some washer fluid will restore a clear and bright view. Especially during nighttime driving, dust on the glass can scatter light, making it necessary to spray washer fluid to maintain optimal transparency of the front windshield. Uses of automotive windshield washer fluid: Widely used for quick decontamination and bright cleaning of various glass surfaces including car windows, rearview mirrors, household glass, office glass, door/window glass, and decorative glass.
8
3
Share

Where to Install the Rear Camera of a Dash Cam?

The rear camera of a dash cam is installed on the top left or top right corner of the license plate. The installation method for a dash cam is as follows: 1. Fix the dash cam near the rearview mirror; 2. Tuck the power cable into the gap of the roof lining, then guide it down along the door frame and tuck it inside the interior trim; 3. Route the power cable behind the glove box and connect it to the cigarette lighter. The functions of a dash cam include: 1. Protecting the driver's legal rights and avoiding extortion or blackmail; 2. Enabling traffic police to handle accidents accurately and quickly; 3. Reducing driver violations and lowering the probability of traffic accidents; 4. Assisting courts in making accurate judgments when handling traffic accident cases.
19
5
Share

Are there any requirements for steering wheel operation in Subject 2?

Subject 2 does not specify requirements for steering wheel hand gestures in its assessment content. The relevant explanations are as follows: 1. Steering wheel grip method: Imagine the steering wheel as a clock face. The correct hand position is to place the left hand between the 9 and 10 o'clock positions and the right hand between the 3 and 4 o'clock positions. In the event of a collision, this posture is more conducive to supporting the body. 2. Precautions: While driving, except when necessary for operation, do not operate the steering wheel with one hand for extended periods, nor place your hand on the gear shift or window frame for long durations. When turning the steering wheel, avoid excessive force or sudden jerky movements, and do not turn the steering wheel when the vehicle is stationary. When driving on bumpy roads, hold the steering wheel firmly with both hands to prevent loss of control and potential accidents.
5
0
Share

Do You Need to Remove the Sunroof to Replace the Sunroof Seal?

Replacing the sunroof seal does not require removing the sunroof. The functions of the seal are as follows: 1. Gap Filling: Automotive seals serve to fill various gaps between body components, providing functions such as shock absorption, waterproofing, dustproofing, sound insulation, and decoration. After selecting the appropriate seal, the original seal must be removed before installation. Special attention should be paid to cleaning residual adhesive, accumulated dust, and dirt over the years. If the seal is not cleaned properly and does not adhere firmly, it is better not to replace it. 2. Enhancing Driving Comfort: The seal effectively protects the vehicle body and improves driving comfort. It is applied to door panels, door frames, front and rear windshields, engine hoods, and trunk lids.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.