How to Turn on the Fog Lights in a Skoda Octavia?

1 Answers
VanLucille
07/29/25 3:46pm
Skoda Octavia fog light operation method: Rotate the light control knob on the left side of the steering wheel to the small light or low beam positions. The first position activates the front fog lights, and the second position activates the rear fog lights. Vehicle fog lights can increase visibility distance, improving the visibility of the driver and surrounding traffic participants, allowing approaching vehicles and pedestrians to detect each other from a greater distance. The Skoda Octavia is the first sedan under the SAIC Skoda brand, with dimensions of 4572mm in length, 1769mm in width, 1462mm in height, and a wheelbase of 2578mm. The Skoda Octavia adopts Skoda's new family design language, showcasing a simple, fashionable, and elegant styling.
Was this review help?
8
2
Share
More Forum Discussions

What is BYD's battery degradation standard for battery replacement?

BYD's battery degradation standard for battery replacement is as follows: 1. 1 to 10 years: The degradation rates are 8%, 4%, 2%, 2%, 2%, 1.5%, 1.5%, 1.5%, 1.5%, 1.5% respectively. 2. Over three years: The battery degradation level has already affected normal usage. 3. Grading: When the current battery capacity is lower than the nominal capacity, it is considered degraded. When the capacity falls below 20%, it is deemed severe battery degradation. There are many reasons for battery degradation, mainly including: 1. Quality issues: Poor battery quality itself. 2. Poor charger: Using inferior chargers. 3. Working environment: Operating in high or low-temperature environments for extended periods. 4. Overcharging and discharging: Using the battery until the remaining charge is below 3%. Circuits have protection, but it occasionally happens. 5. Radiation: Long-term use of the battery in areas with strong electromagnetic radiation (which can interfere with the conductivity of metals inside the battery).
10
3
Share

Causes and Solutions for Car Air Conditioner Evaporator Freezing

The causes and solutions for car air conditioner evaporator freezing are as follows: Compressor malfunction due to prolonged use: Reduced compression efficiency or damage to the compressor's gas distribution system can lead to excessively low pressure, causing freezing. The freezing typically occurs in the front section of the evaporator. Adding some refrigerant can resolve the issue. If the problem persists, the compressor must be replaced. Excessive refrigerant: Some air conditioners may have refrigerant added due to relocation or leaks. Improper handling by maintenance personnel can result in too much refrigerant, causing excess refrigerant to flow to the rear section of the evaporator and freeze. This type of freezing usually occurs in the rear section of the evaporator and around the compressor's return pipe. Releasing the excess refrigerant will resolve the issue. Dirty evaporator: After prolonged use, dust from the air or microorganisms generated by the evaporator can accumulate on the evaporator, obstructing airflow, reducing heat exchange, and causing the evaporator temperature to drop too low, leading to freezing. The freezing occurs in the rear section of the evaporator. After the ice melts, rinse the evaporator with water and gently brush along the fins with a soft brush, being careful not to wet the electrical components. Cleaning thoroughly will resolve the issue.
8
0
Share

What Causes the Steering Wheel to Be Misaligned When Driving Straight?

The reasons for the steering wheel being misaligned when driving straight are as follows: 1. Wear and looseness of the steering tie rod ball joint pin, or loosening of the fastening nut. 2. Severe wear of the steering knuckle kingpin and bushing, leading to increased clearance. 3. Excessive axial clearance of the front wheel bearings or wear. Solutions are as follows: 1. Adjust the toe-in. Collisions during driving can deform the steering rod and tie rod, wear out various ball joints, or cause irregular tire wear, leading to increased or decreased toe-in. 2. Wheel dynamic balance. After a certain mileage, the original wheel balance weights may be lost, or the wheel hub may be deformed, causing the front end to wobble and the steering wheel to shake at high speeds. 3. Check the tie rod. Looseness of the tie rod ball joint or bracket can cause instability during driving. 4. Check the wheel hub bearings. Loose wheel hub bearings or severe wear of the left and right steering knuckle ball joints can lead to inaccurate front wheel alignment. 5. Check the steering damper. A damaged or leaking steering damper, or deformed front suspension springs, can also affect the car's stability during driving.
11
3
Share

Where are the vehicle clearance lights located?

Vehicle clearance lights are located at the outermost lights on the front and rear of the car. Their functions are: 1. According to GB7258 "Technical Conditions for Safe Operation of Motor Vehicles" Article 8.2.6, vehicles with an unladen height exceeding 3.0m or a width exceeding 2.10m must be equipped with clearance lights; GB4785 "Installation Requirements for External Lighting and Signaling Devices of Motor Vehicles and Trailers" Article 4.3.17 specifies the quantity, configuration, layout, light color, installation position, and circuit connection requirements for clearance lights. Without altering the existing connection method, adding a red light distribution surface to the rear of the front clearance light effectively incorporates the function of a rear clearance light. 2. Function of clearance lights: The term "clearance light" can be understood literally - "clearance" indicates warning, and "light" refers to outline. These are warning lights that serve as cautionary signals to alert other vehicles. 3. Installed along the top edges of the vehicle, they indicate both the height and width of the car. Safety regulations mandate that vehicles taller than three meters must be equipped with clearance lights. The color specification for clearance lights is white at the front and red at the rear.
20
3
Share

Can I Renew My Driver's License a Few Days Late?

You can renew your driver's license after the renewal deadline. However, you are not allowed to drive from the time your license expires until you receive the new one. If caught driving during this period, you will be penalized for driving without a valid license. What to do if the renewal deadline is exceeded by less than one year: If the renewal deadline is exceeded by less than one year, the driver's license will be in an "overdue for renewal" status. The driver can bring their ID card, expired driver's license, and a medical certificate issued by a county-level or military regimental-level medical institution to the vehicle management office to complete the renewal procedure. No written or practical tests are required to renew the license. What to do if the renewal deadline is exceeded by more than one year but less than three years: If the renewal deadline is exceeded by more than one year but less than three years, the driver's license will be in a "canceled but recoverable" status during this two-year period. Although the license is canceled, it can be reinstated. The driver only needs to take the written test (Subject 1) at the vehicle management office. Upon passing the test, they can proceed with the normal renewal process. What to do if the renewal deadline is exceeded by more than three years: In this case, the driver's license will be in a "canceled" status, meaning the driving qualification is revoked and cannot be reinstated. The driver must retake all required tests, just like a new applicant, to obtain a new driver's license.
6
1
Share

What is the reason for showing 'No Driver Training Attended' when scheduling Subject 1 exam?

The reasons for showing 'No Driver Training Attended' when scheduling the Subject 1 exam include insufficient training hours and the examinee's information not being entered into the system. Insufficient training hours: The Subject 1 exam requires at least 12 hours of completed study before taking the test. Information not entered into the system: Consult your instructor about the situation and remind them to enter your information promptly. Subject 1 exam process: Follow the staff's arrangements and collect your driving training file in order at the waiting area; Bring and present your ID card for inspection by the supervising officer; Mobile phones must be turned off when entering the exam area; No loud talking is allowed in the exam area; Regulation textbooks are not allowed in the exam area (or should be kept in your bag); After the exam, keep your ID card safe and submit the file to the 'Document Submission Window' at the front of the exam area; Candidates who pass the exam will sign under the guidance of the staff at the exit before leaving; Candidates who fail the exam may leave the exam area and wait for notification from their driving school staff about the retake time.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.