How to Turn On the Ambient Lights in the 2020 VV5?

Can Pop-up Headlight Cars Be Driven on the Road?

Mazda MX-5 with pop-up headlights cannot be driven on the road in China. Here are some precautions regarding car driving: Cold car warm-up: Proper warm-up helps the engine oil form an "oil film" between engine components, thereby reducing component wear. Timely gear shifting: When driving a manual transmission car during the break-in period, shift gears promptly and appropriately, avoiding incorrect behaviors such as high gear with low RPM or low gear with high RPM, and do not use a single gear for an extended period. Timely maintenance: Simply follow the manufacturer's recommendations in the vehicle manual, and after reaching a certain mileage or time, promptly inspect and maintain the vehicle, replace engine oil, oil filter, etc., and conduct a comprehensive inspection of the chassis system. Avoid emergency braking: Emergency braking not only impacts the braking system during the break-in period but also increases the impact load on the vehicle's chassis and engine.

6

1

Share

What Causes a Motorcycle to Have Poor Acceleration?

Here are the reasons why a motorcycle may have poor acceleration: 1. Clogged air filter: Once the air filter is clogged, the engine's air intake will be restricted, leading to incomplete combustion and reduced engine efficiency, which inevitably affects acceleration performance. 2. Fuel system not cleaned for a long time: Whether it's fuel injection or a carburetor, regular cleaning is necessary, with carburetors requiring more frequent cleaning. 3. Ignition system: If there is a noticeable jerking sensation while riding, 80% of the time it is caused by the ignition system. The components most likely to fail in the ignition system are the ignition coil, high-voltage coil, and connecting wires. 4. Engine failure: Issues such as valve leakage, worn piston rings, or aging cylinder blocks can lead to poor engine acceleration. This is mainly due to decreased cylinder pressure, which alters the engine's combustion state, resulting in weak acceleration.

9

0

Share

What is the width of each lane on the highway?

Highway lane width is 3.75 meters. Here are several important points to note when driving on highways: Speed control: Highways have strict speed limits. According to national regulations, the maximum speed on highways must not exceed 120 kilometers per hour, and the minimum speed must not be lower than 60 kilometers per hour. Driving too fast increases the probability of traffic accidents, while driving too slow will hinder following vehicles and prevent the highway from functioning effectively. Maintain distance: Following vehicles must maintain sufficient distance from the vehicle in front in the same lane to allow for valuable reaction time in case of emergencies. During nighttime driving when visibility is lower, the distance between vehicles should be increased to leave extra space. Stay in your lane: Drivers should always pay attention to roadside and pavement markings. It is prohibited to ride or drive on lane dividers, nor is it allowed to occupy the overtaking lane for extended periods.

10

4

Share

Which Lane Should a Motorcycle Stop in at a Traffic Light?

Here is an introduction to the waiting positions for motorcycles at traffic lights: 1. Left turn: Stop in the left-turn lane. 2. Straight: Proceed straight in the straight lane. 3. Right turn: If there is no separate right-turn signal light, you can turn right directly. If there is a separate right-turn signal light, you must follow the right-turn indicator signal. Below is additional information on situations where motorcycles cannot make a U-turn at traffic light intersections: 1. Crosswalk: U-turns are not allowed on crosswalks. 2. Left-turn lane: U-turns are not allowed when there is no left-turn lane. 3. No U-turn: U-turns are not allowed if there is a 'No U-turn' sign. 4. Left turn: If left turns are prohibited, U-turns are also not allowed. 5. Road centerline: U-turns are not allowed when the road centerline is a solid yellow line. 6. Yellow grid lines: U-turns are not allowed on yellow grid lines.

13

1

Share

Should You Engage the Handbrake or Shift Gears First After Getting in the Car?

Driving precautions and the hazards of engaging the gear without releasing the handbrake are as follows: Driving Precautions: Whether it's a manual or automatic transmission, the most important thing when starting is to shift into gear first, then release the handbrake. The handbrake serves as the final safety measure; only after fully engaging the gear and before moving should you release the handbrake—this practice is very safe. When shifting gears, move quickly from P to D to avoid a reverse impact when passing through R, which is harmful to the transmission. Hazards of Engaging the Gear Without Releasing the Handbrake: If you engage the gear but do not release the handbrake, all the power output from the engine will be absorbed by the torque converter, causing its temperature to rise sharply and potentially burn out over time. For dual-clutch transmissions, engaging the gear without releasing the handbrake keeps the clutch friction plates in a semi-engaged state, which can lead to burning out the friction plates if prolonged, so it's necessary to start moving as soon as possible.

2

1

Share

What Causes the Click Sound When Starting the Car?

This sound is caused by friction between the starter pinion gear and the flywheel. It is necessary to inspect the starter one-way clutch, as damage to this component can lead to such phenomena. Below are other possible abnormal sounds and their causes when starting the car: High-pitched squealing: This kind of squeaky noise is caused by belt slippage, which could be due to insufficient tension from the tensioner pulley or the belt being stretched from prolonged use. For a normal belt and tensioner pulley, when twisting the belt by hand with slight force, the belt should not twist more than 90 degrees. If the belt can be twisted over 90 degrees with minimal effort, it indicates that the belt or tensioner pulley is loose. Ticking sound: This noise could be the sound of the engine's valve train closing. In an engine, the valve train is typically the noisiest component; this sound is produced when the intake and exhaust valves close, and it is usually audible after startup. Alternatively, it could be the sound of the spark plug firing. Metal grinding noise: This sound likely occurs because the vehicle has been parked for an extended period, causing the oil to drain into the oil pan. During the initial startup, components may not be adequately lubricated, resulting in metal grinding sounds, which should disappear once oil pressure builds up.

1

Share

How to Turn On the Ambient Lights in the 2020 VV5?

Can Pop-up Headlight Cars Be Driven on the Road?

What Causes a Motorcycle to Have Poor Acceleration?

What is the width of each lane on the highway?

Which Lane Should a Motorcycle Stop in at a Traffic Light?

Should You Engage the Handbrake or Shift Gears First After Getting in the Car?

What Causes the Click Sound When Starting the Car?

What does the blue P stand for in parking lots?

Which insurance company should I buy motorcycle insurance from?

Can Private Cars Drive in BRT Lanes?

What does automatic four-wheel drive mean?