How to turn on the air conditioning cooling in a Mercedes-Benz C200?

2 Answers
IsabelAnn
09/01/25 7:16am
Method to activate the cooling mode of the Mercedes-Benz C200 air conditioning: When the automatic air conditioning is turned on, the vehicle generally adjusts to a suitable temperature based on the interior and exterior temperatures. If there are special requirements, it can also be manually adjusted. Press the AC button to turn on the cold air, and adjust the knob towards the blue area to open the cold air. Below are the relevant details of the Mercedes-Benz C200: 1. The body dimensions of the Mercedes-Benz C200 are 4526/1728/1427mm, with a wheelbase of 2715mm. 2. The Mercedes-Benz C200 is equipped with an inline 4-cylinder turbocharged engine, with a maximum power of 120kw/5500rpm and a maximum torque of 240nm/3000-4000rpm.
Was this review help?
17
0
Share
LaTessa
09/14/25 3:04am
Last time I drove my friend's Mercedes-Benz C200, I specifically learned how to operate the air conditioning. After starting the car, I first found the AC button with the snowflake symbol on the center console and pressed it—the light indicates the compressor is on. Then, I turned the left temperature knob toward the blue direction; the lower the number, the cooler it gets. I usually set it between 18-22 degrees. The fan speed can be controlled with the right knob, and pressing the AUTO button lets the system adjust the airflow automatically. When cooling, remember to turn on the recirculation button (the one with the arrow inside the car) for faster cooling. After ten minutes, I realized it wasn't cold enough and found the vents were blocked by my partner's small toy—moving it fixed the issue. A dirty cabin air filter can also affect performance, so it's good to replace it during maintenance.
Was this review help?
11
5
Share
Expand All
More Forum Discussions

How to Open the Trunk of the New Sagitar?

The methods to open the trunk of the New Sagitar are: 1. When the vehicle is unlocked, there is a soft rubber handle under the lower edge of the Volkswagen logo. Gently lift it to open; 2. There is a trunk unlock button in the middle of the remote key. Hold it for 2 seconds, and the trunk will automatically unlock and lift. By pulling the trunk unlock button on the driver's side door, you can open it from inside the car. The New Sagitar has a length, width, and height of 4655mm, 1780mm, and 1453mm respectively, with a wheelbase of 2651mm. The car is equipped with a rear third headrest, velvet seats, a three-spoke steering wheel, a leather gear knob, a leather handbrake grip, a magnesium alloy handbrake skeleton, an anti-glare interior rearview mirror, and a multifunctional display with gear indication.
7
1
Share

What is the emission standard for cars manufactured in 2013?

Most models manufactured in 2013 comply with the China IV emission standard, while some imported models meet the China V emission standard. Automobiles are mobile sources of pollution, emitting primary pollutants such as carbon monoxide, hydrocarbons, nitrogen oxides, and particulate matter, all of which are environmental contaminants that need to be controlled. The sources of automobile pollutants come from the exhaust pipe, crankcase, and fuel system. With the increasing severity of automobile exhaust pollution, countries around the world have established corresponding regulatory systems for automobile exhaust emissions. These strict regulations have promoted advancements in automobile emission control technologies. As these technologies continue to improve, the formulation of even higher standards becomes possible.
6
3
Share

Is it common to have your driver's license checked on highways?

Highway checks for driver's licenses are relatively rare. They are more common at highway exits in provincial capital cities due to stricter traffic management by local authorities. Additionally, checks are more frequent at borders between provinces or cities, as traffic police from both jurisdictions conduct inspections, increasing the likelihood of license checks. In other areas, it depends on luck—if you happen to encounter a random police check, you may be asked to present your driver's license, license plate, and other relevant vehicle documents. Below are some key points about driving on highways during the probationary period: 1. Accompanied by an experienced driver: It is advisable not to drive alone on highways during the probationary period. New drivers may not be fully familiar with traffic rules and driving precautions, nor accustomed to highway speeds. In emergencies, the high speed may leave little time to react, potentially leading to loss of control and serious consequences. Having an experienced driver (with over 3 years of driving experience) accompany you can provide correct guidance in unexpected situations or mistakes. 2. Consequences: If an accident or vehicle damage occurs while driving on a highway during the probationary period, insurance companies will not cover the claims. If the accident results from illegal behavior, penalties will be more severe. Additionally, accumulating 12 demerit points during the probationary period will result in the revocation of the driver's license. Therefore, it is best to avoid driving alone on highways during this period.
17
3
Share

Where is the ETC installation location for large trucks?

For large vehicles such as trucks and buses, the ETC device should be installed in the middle-lower section. The appropriate installation position should be at a height between 1.2 meters and 2.5 meters, with an installation angle ranging from 30 to 90 degrees. If the vehicle has factory-installed or aftermarket explosion-proof film, which may affect microwave signal transmission, the device should be installed in the microwave skylight zone. ETC stands for Electronic Toll Collection. To apply for ETC, you need to provide the original and photocopies of the vehicle owner's valid ID card and vehicle registration certificate. If the application is made by someone other than the owner, the agent's valid ID card is also required. The photocopy of the vehicle registration certificate should include the page with the most recent annual inspection stamp. Additionally, a bank card under the personal name of someone aged 18 to 60 is needed for deducting highway tolls. Here are some important considerations for ETC installation: Do not obstruct the driver's view. The best location is behind the interior rearview mirror: Many vehicle models have steeply angled windshields, which can reduce the driver's field of vision. Installing the ETC device without considering this may increase blind spots. Placing it on the right side behind the rearview mirror helps avoid obstructing the view. Avoid affecting charging: The ETC electronic tag consumes power but generally doesn't require charging or battery replacement because it has a built-in solar panel for self-charging. Therefore, during installation, avoid the blackened areas on the windshield and positions that might block the solar panel. Do not remove the device arbitrarily once installed: The adhesive backing contains an anti-tamper rod connected to a switch. After installation, the windshield presses this rod inward. If the device is removed arbitrarily, the rod will pop out and trigger the switch, locking the electronic tag and rendering it unusable. In such cases, you would need to visit an ETC service center to unlock it. This mechanism prevents multiple vehicles from sharing one device. When using ETC, note the following: The ETC transaction sensing range is 8 meters. To avoid paying for the vehicle in front due to its faulty ETC device, maintain a distance of at least 10 meters from the vehicle ahead. The ETC lane recognition speed is 20 km/h; driving too fast may result in failed toll deduction due to unreadable vehicle information. If using a debit card linked to ETC, insufficient balance may also cause toll deduction failure.
16
4
Share

What are the impacts of insufficient oil pressure?

Insufficient oil pressure can lead to poor lubrication at critical components such as crankshafts, connecting rods, and camshaft bearings, potentially causing abnormal engine noises, unstable operation, and reduced power output. Additionally, inadequate lubrication at key friction points may result in localized overheating. Continuous operation under low oil pressure can, in severe cases, cause engine bearing seizure (commonly referred to as "spun bearings"), rendering the engine inoperable and requiring bearing replacement or resurfacing. Engine oil, also known as motor lubricant, performs vital functions including friction reduction, auxiliary cooling, sealing, rust prevention, and shock absorption – earning its reputation as the "lifeblood" of vehicles. It consists of base oils and additive packages.
13
3
Share

Should You Shift Gears Based on RPM or Speed?

Shifting gears is primarily based on RPM. The reason a car needs to shift gears is due to new demands on the torque provided by the engine, and the torque the engine can provide is directly related to RPM. It's important to note: For a specific car model, the engine RPM corresponds to a particular speed in different gears. If you know this specific correlation, you can also shift gears based on speed. Different engines have varying power and torque output characteristics, so the corresponding shift RPM also differs. For example, some recommend shifting at 2000 RPM, while others suggest shifting at 2200 RPM.
16
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.