How to Turn On Front and Rear Fog Lights?

1 Answers
DiElias
07/29/25 7:30pm
Front and rear fog lights activation method: Press and hold the fog light buttons to turn them on. Fog lights are divided into front and rear types, with front fog lights typically being bright yellow and rear fog lights red. The symbols for rear fog lights differ slightly from front fog lights—the front fog light symbol has downward light beams while the rear fog light symbol features parallel beams, usually located on the vehicle's dashboard console. Fog lights generally refer to automotive fog lights installed at the front and rear of the vehicle. Due to low visibility in foggy conditions, which limits driver visibility, these lights can extend operational distance. Particularly, the strong penetrating power of yellow fog lights enhances visibility for both drivers and surrounding traffic participants, allowing approaching vehicles and pedestrians to detect each other from a greater distance.
Was this review help?
14
1
Share
More Forum Discussions

How often should the Mazda3 Axela's engine oil be changed?

The maintenance cycle for the Mazda3 Axela is every 6 months or 5,000 kilometers, which means the engine oil should be changed every 6 months or 5,000 kilometers. Precautions for changing engine oil: When adding engine oil, ensure the oil level is between the min and max marks on the dipstick. The oil level should not be below the min mark or above the max mark. If the oil level is below the min mark, it can cause insufficient lubrication in the engine, leading to increased wear. If the oil level is above the max mark, it can increase resistance during engine operation, resulting in reduced power and higher fuel consumption. Always check the oil level carefully when adding oil. Additional precautions for oil changes: Regular oil changes are necessary. Do not mix different types of oil. Purchase high-quality full synthetic oil, which should be changed every 8,000-10,000 kilometers. Semi-synthetic oil should be changed every 5,000-8,000 kilometers, and mineral oil every 5,000 kilometers. Regularly clean the engine air filter and replace the oil filter. After adding oil, sludge and carbon deposits on engine parts will disperse into the oil, causing it to turn black over time. Typically, the need for an oil change is determined by checking the oil's viscosity, not just by observing its color. Insufficient oil can lead to inadequate lubrication and engine seizure, while too much oil can affect vehicle performance and increase fuel consumption.
12
0
Share

What to Do If You Accidentally Added Expired Fuel Additive?

Accidentally adding expired fuel additive will not achieve the effect of cleaning carbon deposits, but it will not have adverse effects on the car. The functions of fuel additive are as follows: 1. Clean Carbon Deposits: High-quality gasoline additives contain purifying factors that can clean harmful substances such as gum deposits in fuel and engine carbon deposits. Continuous use can help remove carbon deposits in the fuel system, including the fuel injector, intake valve, and intake manifold, restoring the vehicle's original power and maintaining optimal performance over the long term. 2. Improve Atomization: Gasoline additives utilize nano-molecular materials to directly attack the long-chain carbon bonds in fuel molecules, creating "micro-explosions" in the combustion chamber. This results in secondary atomization of gasoline, promoting complete combustion, improving thermal efficiency, and reducing fuel consumption. Comparative tests on actual vehicles show that gasoline additives can save 3~15% of fuel. The effect is particularly noticeable during long-distance high-speed driving, making it more economical than usual. 3. Protect the Engine: High-quality gasoline additives consist of organic nano-molecules, cleaning activation factors, and more than 10 other materials, including antioxidants, anti-corrosion agents, and demulsifiers. They are specifically designed to target harmful components in fuel, such as sulfur and gum deposits, as well as engine carbon deposits. Gasoline additives also have functions such as oxidation resistance, cleaning, dispersion, demulsification, anti-corrosion, and lubrication.
9
1
Share

Does the Steering Wheel Automatically Return to Center?

All car steering wheels have an automatic return-to-center function. In professional terms, this steering wheel return is called the steering wheel stability effect. The automatic return-to-center performance is a fundamental feature of vehicles and an important evaluation criterion for vehicle handling performance. All motor vehicles, regardless of the type of steering system or whether they have power assistance, should have the ability to return to center. This is particularly noticeable while driving, as it is difficult to return to a straight position when stationary, but there should still be some return force. To explain its principle in detail: When a car is driving in a straight line, if an external force forcibly changes its original path, the steering wheel will naturally regain the ability to drive straight. Achieving the steering wheel stability effect relies on three core components: the steering wheel, the kingpin, and the front axle. The installation of these three core components follows specific rules, including parameters such as the caster angle, kingpin inclination angle, and wheel camber angle. The kingpin inclination angle refers to the angle between the kingpin axis and the vertical line perpendicular to the ground. Most vehicles are set with a positive value when leaving the factory. The angle between the kingpin axis and the vertical line is the caster angle. When the steering wheel is turned, the tire rotates around the kingpin as the center. The ground's reaction force on the tire lifts the front of the car, and under the vehicle's own gravity, the wheel will return to a position parallel to the direction of travel, making it easier for the steering wheel to return to center.
17
4
Share

Does the new Levin have a cigarette lighter socket?

The new Levin has a cigarette lighter socket. Location of the cigarette lighter: The cigarette lighter position in the new Levin is quite special - it's located inside the center console. You can see it after opening the console lid, making it very concealed. Cigarette lighter: The cigarette lighter is a vehicle device. In its traditional sense, the cigarette lighter draws power from the car's electrical system to heat a metal heating element (either a plate or coil), providing a flame source for lighting cigarettes. With automotive development and evolving user needs, the cigarette lighter socket can typically be equipped with a car power inverter for charging mobile electronic devices. The socket's central spring contact is the positive pole, while the side clips are negative poles. The power supply is directly connected to the car battery, with current and power specifications matching those of the battery.
1
0
Share

What Causes Low Engine Coolant Level in BMW?

BMW engine coolant level may be low due to the following reasons: Specific causes: Possible causes include faulty contacts on the coolant level switch connection, interrupted contacts in the wiring harness, faulty grounding contacts, or damage to the coolant level switch. A stuck float in the reservoir can also lead to low coolant levels in BMW engines. Solutions: To address low engine coolant levels, promptly add coolant to the BMW engine. If the issue persists, it is recommended to visit a 4S dealership for inspection and repair of the engine coolant system.
12
4
Share

How to Replace the Cabin Air Filter in a Mazda 3?

The cabin air filter in a Mazda 3 is located beneath the glove box. The main steps to replace the cabin air filter in a Mazda 3 are as follows: 1. Remove the panel below the glove box to locate the cabin air filter housing. 2. Unscrew the fastening screws on the cabin air filter housing cover to remove the cover. 3. Once the cover is removed, the cabin air filter can be taken out. 4. Insert the new cabin air filter and reinstall everything in reverse order. Below is an introduction to the functions of the cabin air filter: 1. It ensures the filter fits tightly against the housing, preventing unfiltered air from entering the cabin. 2. It separates solid impurities such as dust, pollen, and abrasive particles from the air. 3. It adsorbs moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc., from the air, with strong and long-lasting moisture adsorption capabilities. 4. It prevents the car windows from fogging up, ensuring clear visibility for the driver and passengers and safe driving. It provides fresh air to the cabin, preventing the inhalation of harmful gases and ensuring driving safety. It also effectively sterilizes and deodorizes. 5. It maintains clean air in the cabin, preventing bacterial growth and creating a healthy environment. It effectively separates solid impurities such as dust, pollen, and abrasive particles from the air. It also effectively blocks pollen, ensuring that the driver and passengers do not experience allergic reactions that could affect driving safety.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.