How to Turn on Car Lights at Night?

1 Answers
AniyahAnn
07/29/25 11:16pm
Before starting, turn on the lights to clearly see the road ahead. When parking, stop the car first and then turn off the lights. When driving below 30 km/h, use low beams; when exceeding 30 km/h, switch to high beams. When there is oncoming traffic, promptly switch the lights back to low beams. When driving in well-lit urban areas or sections at night, use low beams and maintain a safe speed. When temporarily parked on the roadside, turn on the parking lights, taillights, and width markers.
Was this review help?
7
5
Share
More Forum Discussions

Is the Fista a B-segment car?

The Fista belongs to the B-segment category. The overall style of the Fista follows a youthful approach, with an exaggerated front fascia, a fastback silhouette, giving it a dynamic appearance, and an interior that exudes a strong youthful vibe. From an exterior perspective, the Fista boasts excellent proportions, and its design conveys the sportiness the designers aimed to express, complemented by the fastback rear end, making the car appear elongated in subjective visual perception. The Fista measures 4660mm in length, 1790mm in width, and 1425mm in height, with a wheelbase of 2700mm, classifying it as a compact car. The Fista is equipped with a 1.6T high-power engine, delivering a maximum power of 150kW at 6000 rpm and a maximum torque of 265Nm between 1500 and 4500 rpm.
18
5
Share

Is it necessary to depress the clutch when shifting to neutral?

Shifting to neutral without depressing the clutch is possible, but it is recommended to develop the habit of depressing the clutch for the following reasons: 1. Shifting to neutral without depressing the clutch requires more effort; 2. It can cause excessive wear on the synchronizers inside the clutch and even damage due to gearshift impact. Coasting in neutral is generally considered a fuel-saving operation, but for modern fuel-injected engine cars, coasting in neutral should be used with caution, and coasting in neutral with the engine off is strictly prohibited. Neutral typically refers to the state where the vehicle's gear lever is not engaged in any forward or reverse gear, and the transmission is completely disengaged from the drive wheels. For manual transmissions, neutral is in the middle position, while for automatic transmissions, it is marked with an "N".
14
3
Share

Where is the engine number of the Baojun 510 located?

The engine number of the Baojun 510 is located at the lower right front side of the cylinder block. The Baojun 510 is equipped with a 1.5L DVVT engine, which adopts General Motors' core technology, delivering a maximum power of 82kW and a maximum torque of 147Nm. It is paired with a CVT continuously variable transmission, featuring both economy and sport modes, and complies with the China VI emission standards. The Baojun 510 is a compact SUV launched by SAIC-GM-Wuling, targeting the young demographic. The vehicle's dimensions are 4220mm in length, 1740mm in width, and 1615mm in height, with a wheelbase of 2550mm. The minimum ground clearance is 185mm when unloaded and 169mm when fully loaded.
8
0
Share

Octavia Valve Clearance Adjustment Method?

The Octavia valve clearance adjustment method is as follows: 1. Warm up the engine until the coolant temperature reaches 80-90°C, open the timing mark inspection hole on the clutch housing and the cylinder head cover, and ensure that the cylinder head bolts are tightened to the specified torque. 2. Rotate the crankshaft to align the "0" mark on the flywheel with the mark line on the clutch housing, ensuring that the curved surface of the intake and exhaust valve rocker arms of the first cylinder contacts the base circle of the camshaft cam, meaning the first cylinder piston is at the compression top dead center. If the rocker arm contacts the cam, rotate the crankshaft 360°; at this point, the valves are in the closed position. 3. Loosen adjustment screw 1 and lock nut 2, use a screwdriver to turn the adjustment screw so that the gap A between the lower end face of the screw and the upper end face of the valve stem 3 reaches the specified clearance value, determined by the thickness of a feeler gauge. Keep the screwdriver steady, tighten the lock nut to the specified torque, then recheck gap A with the feeler gauge. This completes the adjustment of the intake and exhaust valve clearances for the first cylinder. 4. Then, rotate the crankshaft clockwise (viewed from the front of the engine). For a 4-cylinder engine, every 180° rotation allows adjustment of the valve clearance for the next firing cylinder in the ignition order 1-3-4-2. For a 3-cylinder engine, every 240° rotation allows adjustment in the ignition order 1-2-3. The crankshaft rotation angle can be calculated using the number of teeth on the flywheel ring gear.
13
4
Share

Does the Xingrui support CarPlay?

The Xingrui does not support CarPlay. Below is relevant information about the Xingrui: 1. Product Introduction: It is the first sedan built on the CMA Super Matrix architecture. Benefiting from the advanced electronic and electrical architecture of the CMA Super Matrix technology, the Xingrui is the first A-segment sedan equipped with an OTA sustainable function upgrade system. 2. Intelligent Safety: The CMA Super Matrix supports comprehensive OTA upgrades. Additionally, it is equipped with intelligent navigation, forward collision warning, pedestrian recognition, blind spot monitoring, speed limit information reminder, lane keeping assist, start-stop adaptive cruise control, heads-up display, and a fully automatic intelligent parking system with automatic braking. 3. Powertrain: Powered by a Volvo 2.0T engine, the Xingrui features a Volvo Drive-E series 2.0TD engine paired with a 7DCT transmission, delivering a maximum power of 190 horsepower and a peak torque of 300 N·m. Thanks to the CMA architecture, it adopts a MacPherson front suspension, an E-type multi-link independent rear frame, a ZF DP-EPS power steering system, ITT brake pads, and long-travel shock absorbers.
7
5
Share

What is the Mustang?

The Mustang is an automobile under the American Ford Motor Company. Here are some relevant details about the Mustang: 1. Exterior Design: The iconic elongated hood and shorter rear deck mark its 40-year history, with design elements that have become synonymous with the Mustang since the 1960s. These include the C-shaped side scoops, triple-bar taillights, and the galloping horse emblem in the center of the grille. The aggressive, shark-like front end conveys an elusive aura that has been characteristic of Mustang models since the late 1960s. 2. Interior: The cockpit benefits from Ford's investment in car interiors. The innovative design approach revisits Mustang's history with modern manufacturing materials and amenities, including customizable instrument panel colors that push personalization to the extreme. The stylish and functional interior design, along with precise craftsmanship, sets a new standard for performance car design. 3. Powertrain: Equipped with the powerful new MODV-8 engine, the Mustang's all-aluminum structure makes the MODV8 engine 34 kg lighter than its cast-iron counterparts in the same class, while delivering 30 kW more power than the 2004 engine.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.