How to Turn On Bluetooth in an Older Lavida Model?

What is the recommended engine oil model for Buick Excelle maintenance?

Buick Excelle 1.4T originally uses Mobil 1 5W-30 full synthetic oil, while the 1.5L version uses OEM 5W-30 semi-synthetic oil. For later maintenance oil changes, you can choose brands such as Mobil, Shell, Castrol, or Total. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity - 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the vehicle. The latter number represents the kinematic viscosity of the oil at 100°C. A higher value means the oil can maintain its viscosity index better at high temperatures, which can also be understood as providing better lubrication performance under high-temperature conditions. The method for changing the engine oil in a Buick Excelle is as follows: Wait for the engine temperature to cool down, allowing the oil to drain back into the oil pan; Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine for about 30 seconds to allow the oil in the main oil gallery to drain out; Use a special wrench to remove the oil filter; Apply oil to the gasket of the new oil filter and tighten it clockwise by hand; Add new oil through the oil filler cap on the engine valve cover, typically filling about three-quarters of a standard oil container; Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If leaks are found, repairs should be made; After stopping the engine, pull out the dipstick to check that the oil level is within the standard range.

4

3

Share

Which Changan models are equipped with the Blue Whale engine?

There are not many Changan models equipped with the Blue Whale engine, only including the Changan CS75 PLUS, Changan CS35 PLUS Blue Whale Edition, and Eado Blue Whale Edition. Below is some introduction about the Changan CS75 PLUS: 1. Powertrain. It features the "2.0T + Aisin 8AT" golden powertrain combination. The intelligent Blue Whale 2.0T engine, comparable to a 3.5L naturally aspirated engine, delivers an ultra-strong torque of 360N·m. 2. Configuration. The mobile Bluetooth key replaces the physical key, allowing users to unlock/lock the vehicle, locate the car, open the trunk, and remotely park via a smartphone. It also enables remote sharing of Bluetooth key permissions with others, setting usage permissions and key retrieval. Additionally, it incorporates a built-in hardware security solution and a high-level digital identity security management system to safeguard users' digital identity and data privacy.

9

5

Share

How to Remove the Rear Taillight of a Sagitar?

Sagitar rear taillight removal method: 1. Open the trunk and pry off the black cover panel; 2. After prying it open, you can see the fixing screws of the taillight, loosen all the screws with a socket tool and then take it out; 3. When removing the taillight, first unplug the bulb connector. In terms of appearance, the overall styling of the Sagitar leans towards the style of the Jetta, with the headlights perfectly integrated with the front grille, giving the front face a more impactful look. The body lines are clear and distinct, adding to the overall sense of stability. In terms of configuration, the Sagitar is equipped with hill start assist, cruise control, front and rear parking radar, reverse camera, eco-driving mode, seat heating and ventilation functions, and other configurations.

12

0

Share

How to Deal with Steering Wheel Misalignment?

Methods to handle steering wheel misalignment: 1. Before parking and turning off the engine, first return the steering wheel to its original position; 2. Adjust the left and right symmetrical tie rods. The adjustment methods for right deviation and left deviation are different. When adjusting right deviation, first turn the steering wheel fully to the right, then screw the left front wheel's tie rod downward, and also twist the right front wheel's tie rod downward, aiming to make the length of the left front wheel's tie rod consistent with that of the right front wheel's tie rod; 3. Finally, tighten the nuts. Steering wheels can be categorized into single-spoke, dual-spoke, three-spoke, and four-spoke types, and their function is to convert the force applied by the driver to the edge of the steering wheel into torque, which is then transmitted to the steering shaft.

3

1

Share

How to Adjust the Time on the New Roewe 350?

Method to adjust the time on the new Roewe 350: 1. Press and hold the INFO button, then press the confirm button after the time format is displayed; 2. When the hour format of the clock flashes, use the SEEK plus or SEEK minus button to adjust the hour, then press the confirm button; 3. When the minute format flashes, use the SEEK plus or SEEK minus button to adjust the minutes; 4. After adjusting both hours and minutes, press and hold the confirm button to finish. The Roewe 350 is a compact sedan produced by SAIC Motor. The car's dimensions are 4521 mm in length, 1788 mm in width, and 1492 mm in height, with a wheelbase of 2650 mm. In terms of suspension, the front suspension of the Roewe 350 is a MacPherson independent suspension, and the rear suspension is an H-type torsion beam non-independent suspension.

2

1

Share

Precautions After Applying Film to a New Car

Precautions after applying film to a new car are as follows: 1. Avoid rolling the windows up and down for three days after applying the film. 2. Do not wash the car for three days. 3. For vehicles with sunroofs, avoid opening the sunroof while driving, especially at high speeds, for three days. 4. In winter, it is recommended not to roll the windows up and down or wash the car for one week after applying the film. The front and rear films may take about a month to fully dry. During the day, the front film should be exposed to sunlight. Most importantly, do not use the rear window defroster for one month, as turning it on after applying the film in winter can cause bubbles near the heating lines, which cannot be repaired and may lead to unnecessary losses and trouble. 5. If bubbles appear at the edges of the film, visit the installation site for repairs within 24 hours. After this period, the adhesive around the bubbles will have dried, and the film edges will no longer be movable, resulting in creases during the repair process.

15

1

Share

How to Turn On Bluetooth in an Older Lavida Model?

What is the recommended engine oil model for Buick Excelle maintenance?

Which Changan models are equipped with the Blue Whale engine?

How to Remove the Rear Taillight of a Sagitar?

How to Deal with Steering Wheel Misalignment?

How to Adjust the Time on the New Roewe 350?

Precautions After Applying Film to a New Car

What is the minimum ground clearance of the 2019 RAV4?

How to Control the Throttle When Starting a Car?

Can the tires of Wuling Hongguang Plus be upsized?

How to Perform Wheel Rotation?