How to Turn On and Off the Windshield Wipers?

3 Answers
StJulian
07/25/25 7:47am
The method to operate the wiper switch is as follows: To activate the automatic wipers, push the right-hand stalk forward once, which will set it to the automatic wiper position. The car will then indicate 'Automatic wipers are on.' To turn off the automatic wipers, pull the wiper stalk backward and then return it to its original position. The wiper sensor is located in the upper middle section of the front windshield. Ensure the wipers are not obstructed and that the front windshield is clean. The wiper sensitivity control switch is located on the right-hand stalk near the steering wheel. The knob can be used to adjust the wiper's sensitivity to rainfall, automatically regulating the wiper speed to provide the driver with a clear view, enhancing convenience and safety during rainy conditions.
Was this review help?
3
1
Share
Ora
08/11/25 1:34pm
The windshield wiper switch is located on the control stalk on the right side of the steering wheel. To activate the wipers, simply push the stalk downward or upward—pushing down sets a slower speed, while pushing up increases the speed or switches to intermittent mode, depending on your car. Some vehicles even have automatic rain-sensing wipers. Turning them off is easy: just return the stalk to its neutral middle position, and the wipers will stop. Having driven for over a decade, I remember checking the manual when I first got a new car, but once you're used to it, you won't need to. Using wipers promptly in the rain is crucial—otherwise, heavy rain can dangerously obscure your view. By the way, don’t forget to regularly check if the wiper blades are worn or cracked, as damaged blades can leave streaks and impair visibility. Replacement blades are inexpensive. In winter, avoid forcing frozen wipers—defrost them with the heater first to prevent motor damage. Overall, operating wipers is very straightforward, and you’ll master it with a little practice.
Was this review help?
12
5
Share
Expand All
Casey
09/27/25 6:24am
When I first started driving, I was quite confused about operating the wipers. Let me teach you the basics: Once the car is started, locate the long lever on the right side of the steering wheel. To turn on the wipers, push the lever downward or upward—each car may vary slightly, but usually pushing down activates low speed, and pushing up activates high speed or intermittent mode. To turn them off, pull the lever back to the middle position, and they’ll stop. The first time I used them, I forgot to turn them off, and they kept wiping after I parked—pretty silly. I recommend new drivers practice in an empty area before rainy days to avoid panic. Safety first—don’t force driving if visibility is poor. Also, maintain your wipers: if the windshield is too dirty, spray some cleaner and wipe, and replace the blades when they wear out to avoid hazards. Just remember the details—it’s all about practice.
Was this review help?
1
0
Share
Expand All
More Forum Discussions

How many meters apart are the white semicircular distance confirmation markings?

White semicircular distance confirmation markings are installed every 50 meters on both sides of road sections with complex meteorological conditions that affect driving safety, serving as a reference for drivers to maintain a safe following distance. Below are three types of distance confirmation markings: White zigzag distance confirmation markings: These markings have a total width of 300cm with line widths of 40cm or 45cm. Starting from the 0m reference point, they are placed every 5 meters in pairs, with a 50m interval between groups. Five sets are typically installed, though more may be arranged based on site conditions. White semicircular distance confirmation markings: These semicircular markings have a radius of 30cm and are spaced 50m apart, usually installed consecutively along certain road sections. White rectangular distance confirmation markings (expressway distance confirmation markings): Used in conjunction with distance confirmation signs, these are installed on sections prone to overtaking, accidents, or other hazardous conditions. When encountering these markings, drivers should maintain a safe distance from the vehicle ahead to prevent traffic accidents.
16
0
Share

Can Engine Oils Be Mixed?

Engine oils should not be mixed. Different types of oils contain different chemical substances, and mixing them may lead to accidents, posing significant safety hazards. It is advisable to avoid mixing oils whenever possible. Here are some precautions regarding adding engine oil to your car: 1. Pay attention to the timing of oil changes for your car. Under normal driving conditions for a new car, if synthetic oil is used, the oil can generally be changed every 10,000 kilometers, and in some cases, it can even be extended to 20,000 kilometers. 2. Choose the right engine oil. It is recommended to opt for multi-grade oils as they are economical, long-lasting, and efficient, providing better protection for the engine. If the engine is in good condition and the seasonal temperature is low, it is advisable to use oil with lower viscosity to ensure smooth oil flow. 3. The oil level should be slightly below the mark on the dipstick and not overfilled. Never let the oil level fall below the minimum mark, but adding too much oil, exceeding the upper limit on the dipstick, will increase the crankshaft's rotational resistance, reduce the engine's output power, and cause excess oil to enter the combustion chamber, leading to oil burning, blue smoke emission, and increased fuel consumption.
8
4
Share

What Causes Increased Car Noise?

Here are the main reasons for increased car noise: 1. Engine mount rubber aging: After prolonged use, the rubber material of the mounts becomes brittle and loses its noise-reducing function. 2. Car tire wear: Car tires are the most prone to wear. As tires and road surfaces gradually wear and age, the noise reduction and shock absorption effects of the tires diminish, leading to increased noise. 3. Shock absorber component aging: When shock absorber parts age, their damping effect decreases, causing passengers to feel more vibrations and noise inside the car. 4. Low oil viscosity: High-viscosity oil maintains the lubrication of engine components, but after prolonged use, the oil viscosity decreases, reducing its lubrication and anti-wear properties, which in turn increases engine noise. 5. Seal aging: The external sealing of the car is crucial for noise control. If engine noise is heard from the bottom of the car during a noise source inspection, the seals should be checked.
3
0
Share

How to Diagnose Clutch Slippage Faults?

Here are the symptoms of clutch slippage: 1. When starting the car, fully releasing the clutch pedal does not allow the car to start or makes starting difficult. 2. During acceleration, the vehicle speed does not increase with the rise in engine RPM, and the engine's power is not fully transmitted to the drive wheels, resulting in weak driving performance. 3. When fully loaded or going uphill, slippage becomes more noticeable, and in severe cases, a burnt smell from overheated friction linings may be emitted. Here are the possible causes of clutch slippage: 1. The clutch pedal free play is too small or nonexistent, causing the release bearing to constantly press against the diaphragm spring, keeping the pressure plate in a semi-engaged state. 2. Reduced elasticity of the diaphragm spring. 3. Excessive wear of the friction disc leading to thinning, surface hardening, oil contamination, or exposed rivets. 4. Loose connecting bolts between the clutch and flywheel. 5. Improper adjustment of the release levers.
7
3
Share

How to Check Tire Date?

Here are the methods to check the tire date: 1. On the outside of the tire, there is a set of numbers on the sidewall. The last four digits of this marking provide information about the production date. It consists of four digits "AABB," where the first two digits "AA" indicate the week of the year, and the last two digits "BB" indicate the year. 2. For example, if the last four digits of the DOT marking on the tire are 0807, it means the tire was produced in the 8th week of 2007, which is around late February 2007. Similarly, a marking of 1606 indicates production in the 16th week of 2006, which is around mid-April 2006.
20
3
Share

Symptoms of Worn Ball Joints in Cars

Here are the main symptoms of damaged ball joints in cars: 1. Abnormal noises when driving on uneven roads. 2. Unstable driving with left-right swaying. 3. Excessive steering play, brake pulling, and steering failure. Here is more information about car ball joints: 1. The function of car ball joints is to transmit power between different axes through spherical connections, providing multi-angle rotation. This allows smooth steering of the steering mechanism, reducing vibration and ensuring smooth steering. 2. Car ball joints include outer ball joints and inner ball joints, equivalent to the front axle and steering knuckle. The ball joint consists only of the ball head and steel cup, with the steel cup divided into inner and outer steel cups. The inner ball joint is fixed on the front axle, while the outer ball joint fits over the inner ball joint and can rotate back and forth.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.