How to turn off the TRIP on the Civic dashboard?

What are the drawbacks of Evans Waterless Coolant in the US?

Evans Waterless Coolant currently has the issue of a relatively long filling time and workflow. Compared to conventional coolant, it is more troublesome to replace and requires more complex procedures. Below is relevant information about coolant: Introduction: Coolant, fully known as antifreeze coolant, refers to a coolant with antifreeze properties. Antifreeze prevents the coolant from freezing during cold seasons when the vehicle is parked, which could otherwise cause the radiator to crack and damage the engine cylinder block. Product Performance: Coolant consists of three components: water, antifreeze, and additives. Depending on the antifreeze component, it can be classified into alcohol-based, glycerol-based, ethylene glycol-based, and other types of coolants. Alcohol-based coolant uses ethanol (commonly known as alcohol) as the antifreeze agent. It is inexpensive, has good fluidity, and is simple to prepare, but it has a relatively low boiling point, is prone to evaporation loss, has an easily elevated freezing point, and is flammable.

17

0

Share

Does an automatic transmission car have an accelerator and a brake?

An automatic transmission car has an accelerator and a brake. In automatic transmission models, the left pedal is the brake, and the right pedal is the accelerator, with only two pedals; in manual transmission models, the far left is the clutch, the middle is the brake, and the far right is the accelerator, totaling three pedals. When driving an automatic transmission car daily, place your left foot naturally on the left-side space for rest, and use your right foot to control the accelerator and brake. However, there is one situation where both feet are needed simultaneously: during steep hill starts, you can use your left foot to control the brake to prevent the car from rolling backward. Precautions for driving an automatic transmission car: Many novice drivers often confuse or make mistakes when safely driving an automatic transmission car, mistaking the accelerator pedal for the brake pedal, leading to collision accidents. In normal economic driving mode, be sure to release the accelerator pedal after the engine RPM rises to a certain level when pressing it down.

16

4

Share

What are the requirements for learning to drive?

There is an age requirement for learning to drive and obtaining a driver's license, which is 18 years or older. Below is some information about the driver's license test: 1. Subject 1: Road traffic safety laws, regulations, and related knowledge test. It is a written test conducted on a computer, with a full score of 100, and a passing score of 90 or above (including 90). 2. Subject 2: Field driving skills test, conducted with a real vehicle in a designated area. The result is either pass or fail. It includes five mandatory tests conducted in sequence: reversing into a garage, parallel parking, S-curve driving, right-angle turning, and hill start and stop. The full score is 100, and a passing score is 80 or above (including 80). 3. Subject 3: Road driving skills test, conducted on a road or simulated area with a real vehicle. The full score is 100, with passing scores of 90 or above for large buses, 80 or above for large trucks, and 70 or above for other vehicle types. 4. Subject 4: Safe and civilized driving-related knowledge test. It is a written test with a full score of 100, and a passing score of 90 or above (including 90).

9

4

Share

How to Adjust for Consistently Crossing the Line at the Last Turn of an S-Curve?

Before entering the curve, you should slow down in advance and follow the principle of taking the outer line. Try to choose a route with a large turning radius as much as possible. For example, if you are preparing to turn left, the vehicle should drive on the right side. Here are the relevant instructions: 1. When the left corner of the car touches the right sideline: turn the steering wheel one circle to the left, keeping the left corner of the car pressing against the right sideline. 2. After completing the right line of the first curve: keep the direction unchanged, and when the right corner of the car touches the right sideline, straighten the direction. 3. Observe the engine cover: when you see the left one-third of the engine cover touching the left line of the right turn, turn the steering wheel one circle to the right. 4. After the vehicle exits the curve: align the front of the car with the exit of the S-curve, straighten the direction, and continue driving forward to exit the curve test area. 5. Do not turn the steering wheel too sharply: generally, you turn the wheel one circle and then observe and adjust accordingly.

4

0

Share

What does the push button on a car mean?

Here is the relevant introduction about the push button on a car: push means press, and in automotive language, it has three meanings: 1. The PUSH in the middle of the air direction (also called mode) gear knob (with a glass defrosting pattern below), pressing it turns on the light and activates the rear window glass defrosting; 2. The PUSH in the middle of the temperature (also called cold/warm) gear knob (with a pattern of a half-circle with an arrow inside a car, commonly known as the internal circulation symbol), pressing it turns on the light and activates the internal circulation. 3. The third meaning of push is equivalent to the handbrake. The professional term for the handbrake is auxiliary brake, which differs in principle from the main brake. It uses a steel cable connected to the rear brake shoes to brake the car. Long-term use of the handbrake will cause the steel cable to undergo plastic deformation. Since this deformation is irreversible, long-term use will reduce its effectiveness, and the handbrake's travel will also increase. A return spring is used in conjunction with the handbrake. When the handbrake is pulled to brake, the spring is stretched; when the handbrake is released, the spring returns to its original length. Long-term use of the handbrake will also cause corresponding deformation of the spring. For small cars, the handbrake is sometimes located behind the transmission, connected to the drive shaft, where there is a brake disc, similar to a disc brake (though drum brakes also exist), and then the pulling force is transmitted there through a steel cable to achieve parking braking.

15

0

Share

Can halogen headlights be replaced with LED bulbs?

Halogen headlights can be replaced with LED bulbs. First, you need to check whether your vehicle originally comes with a lens. If the vehicle does not have a lens, simply replacing it with an LED bulb will generally fail the annual inspection. Generally speaking, even if the original halogen headlights come with a lens, they may not be suitable for replacement with LED bulbs. The differences between halogen headlights and LED headlights: 1. Color difference: Halogen headlights have a yellowish color, while LED headlights have a bluish color. 2. Power difference: Halogen headlights have a power range of 55W-65W, whereas most LED headlights have a power of around 20W. 3. Lifespan: The normal lifespan of ordinary halogen headlights is generally 4-6 years, while LED headlights can last for tens of thousands of hours.

9

1

Share

How to turn off the TRIP on the Civic dashboard?

What are the drawbacks of Evans Waterless Coolant in the US?

Does an automatic transmission car have an accelerator and a brake?

What are the requirements for learning to drive?

How to Adjust for Consistently Crossing the Line at the Last Turn of an S-Curve?

What does the push button on a car mean?

Can halogen headlights be replaced with LED bulbs?

Is Audi's On-Demand Four-Wheel Drive Useful?

What Causes the Rattling Noise in Tesla on Bumpy Roads?

What car model is izda?

The Only Method for Motorcycle License Plate Transfer?