How to Turn Off the Speed Limiter on Volkswagen Lavida?

Can You Continue Driving When the ABS Light Is On?

ABS fault light is on, it is recommended not to continue driving, because the ABS light on means the vehicle's anti-lock braking system is faulty. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it impossible for the driver to slow down or adjust the vehicle's trajectory, posing significant safety hazards. There are various states of the ABS light being on, and the causes and solutions differ for each state, as detailed below: State 1: ABS fault light stays on (most common). Cause 1: The sensing part of the ABS speed sensor is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the speed and the wheel's slip rate, thus unable to issue appropriate commands to regulate braking. Solution: Clean the dirt on the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system lines or poor contact of the ABS relay, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently turns on and off, extinguishing when accelerating. Cause: When multiple vehicle electrical devices are used, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, and the ABS indicator light turns off; the ABS system's power supply voltage is too low, such as due to poor contact at terminals or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start until the engine is turned off. Cause: Poor contact in the ABS hydraulic valve body's grounding circuit; poor contact in the ABS hydraulic valve body's wiring connector; ABS computer failure. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light turns on during high-speed driving. Cause: During high-speed driving, the ABS computer calculates that the rear wheel speed differs significantly from the front wheel speed; incorrect tire specifications or incorrect wheel rim specifications. Solution: Refer to the vehicle's tire specifications and wheel rim specifications, as indicated on the sticker near the fuel tank cap. State 5: ABS warning light intermittently turns on and off. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down to the bottom with your finger, then release the brake pedal to complete the self-setting position; replace the brake light switch.

19

5

Share

How to Enable Wireless Charging for Phones in Lynk & Co 06

Make sure there are no objects on the WPC surface. Click on Functions on the central display – Settings – Smart Connectivity – NFC & Wireless Phone Charging. Tap on Wireless Phone Charging to activate/deactivate the feature. Place your phone in the center of the charging pad.

14

5

Share

How to Adjust the High Beam Height of the Lynk & Co 03?

First, there is a black plastic button on the far left side of the instrument panel near the door that can be rolled up and down. Next to it, there are indicator lines ranging from thick to thin, and you can adjust the headlight height by rolling the button up and down.

14

2

Share

How to Fold Down the Rear Seats of the Lynk & Co 05?

Lynk & Co 05 rear seats can be folded flat. There is a red button near the door next to the rear seat headrest. Press the button. Then pull the car seat downward to fold down the rear seat. Repeat the same operation twice to fully fold down all rear seats.

1

0

Share

How to Set the Memory Seat in Lynk & Co 05?

Press the start switch, adjust the seat and rearview mirror to your preferred position, then press the memory button M. The indicator light on the button will illuminate. Within a short time, press and hold the position 1 button until the indicator light on the M button goes off and a sound reminder is heard. The settings will then be stored under the position 1 button.

9

5

Share

How to Open the Hood of a Lynk & Co 03?

Under the dashboard in the cockpit, there is an engine compartment hood switch. Lift it twice to fully open the front hood, then simply lift it up. After pulling the switch inside the car, you need to lift the hood. On the driver's side, there is a front hood switch that needs to be pulled twice.

14

2

Share

How to Turn Off the Speed Limiter on Volkswagen Lavida?

Can You Continue Driving When the ABS Light Is On?

How to Enable Wireless Charging for Phones in Lynk & Co 06

How to Adjust the High Beam Height of the Lynk & Co 03?

How to Fold Down the Rear Seats of the Lynk & Co 05?

How to Set the Memory Seat in Lynk & Co 05?

How to Open the Hood of a Lynk & Co 03?

How to Pass the Driver's License Physical Exam with Color Weakness?

Which is Better: Hybrid or Plug-in Hybrid?

What to Do When Car Windows Freeze in Winter?

What are the benefits of cleaning the throttle body?