How to turn off the rear wiper on the Q3?

1 Answers
Katniss
07/30/25 4:44am
For the Q3 wiper controls, pulling the switch inward activates the front wipers, while pushing it outward activates the rear wiper. When the rear wiper is engaged, simply push the switch upward to turn it off. Relevant details are as follows: 1. In terms of exterior design, the domestic Q3 shares nearly identical styling with the imported version. 2. The interior features standard black leather seats and a black leather-wrapped steering wheel accented with silver chrome trim. 3. Powertrain options mirror the imported model - the 35TFSI comes with a 170hp 2.0T engine, while the 40TFSI gets a higher-output 211hp 2.0T unit.
Was this review help?
13
0
Share
More Forum Discussions

What to Do If the Front Wheel Crosses the White Line Due to Untimely Lane Change?

If the front wheel crosses the white line due to an untimely lane change, there is a high probability of being penalized for violating the prohibition line indication. This may result in a fine and a deduction of 3 points from the driver's license. At traffic light intersections, most are equipped with electronic cameras that can easily capture such violations, unless the three required photos are not taken—in which case no points will be deducted. Before approaching a traffic light intersection, avoid changing lanes arbitrarily. If you have already entered a lane separated by a solid line, even if you have chosen the wrong lane, continue driving forward and find the next intersection to correct your route. Always pay attention to road markings and signs while driving, and remember that lane changes should only be made where dashed lines are present. Maintain control of the steering wheel to keep the vehicle centered in the lane, and novice drivers should frequently check the rearview mirror to ensure the vehicle is not crossing any lines.
1
1
Share

Where is the Unlimited-Speed Highway in China?

China's unlimited-speed highway is the Hangzhou-Ningbo Expressway, and its parallel line has officially entered the construction phase. The starting point is at the Xiasha Hub of the Hangzhou Ring Expressway, and the endpoint is at the Chaiqiao Hub of the Ningbo Chuanshan Port Expressway, with a total length of approximately 161 kilometers. The Hangzhou section is about 9 kilometers, the Shaoxing section is about 29 kilometers, and the Ningbo section is about 123 kilometers. It is planned to have six lanes in both directions and is expected to be completed and open to traffic by 2022. The Hangzhou-Ningbo Expressway is not truly unlimited in speed. Unlimited-speed highways are also known as super highways. After considering factors such as drivers, passengers, and vehicles, the design speed of this highway is expected to exceed 120 km/h, aiming to meet the technical standards of Italy's highways, which have a speed limit of 150 km/h.
2
3
Share

What is the function of a car's three-way catalytic converter?

The function of a car's three-way catalytic converter is to enhance the activity of three gases—CO, HC, and NOx—when high-temperature exhaust gases pass through the purification device, while converting the three main harmful substances in the exhaust into harmless substances. The following conditions may occur if the three-way catalytic converter is damaged: Decreased engine power performance: Decreased engine power performance, increased fuel consumption. During driving, the three-way catalytic converter is prone to damage from road impacts, such as scraping or strong vibrations, leading to collisions that may fracture the converter's substrate. This can easily block the exhaust passage, resulting in reduced power performance, increased fuel consumption, and worsened emissions. Increased exhaust passage resistance: Due to faults in the fuel supply system, ignition system, etc., engine overheating or backfiring can cause the catalytic converter substrate to sinter or peel off, increasing exhaust resistance. This also leads to greater exhaust passage resistance and worsened emissions.
6
1
Share

What is the fuel consumption of the Jetour X70?

Jetour X70 manual transmission models have an average actual fuel consumption of 8.44L per 100Km, while automatic transmission models have an actual fuel consumption of 9.36L per 100Km. Below is more information about the Jetour X70: Positioning: The Jetour X70 is positioned as a midsize SUV, with dimensions of 4720mm in length, 1900mm in width, and 1710mm in height, and a wheelbase of 2745mm. Power: It is equipped with Chery's 1.5T engine, which boasts a thermal efficiency of up to 37.1%, a maximum power of 150 horsepower, and a peak torque of 210 Nm. The transmission system is matched with a 5-speed manual or 8-speed automatic transmission.
4
5
Share

What is the normal range for car tire pressure?

The normal range for car tire pressure is between 230 and 250 kilopascals (kPa). Generally, the manufacturer's recommended values can be found in the vehicle's user manual, on the label next to the driver's door, in the drawer near the driver's seat, or on the fuel tank cap. Precautions for car tires: Do not use repaired old tires. Once a tire has been repaired, its load-bearing capacity significantly decreases, and there is a risk of the repaired area rupturing again, especially in summer when tire pressure tends to rise. Repaired tires become very fragile during long-distance driving. Use nitrogen to inflate tires. Nitrogen inflation can reduce the occurrence of blowouts. From a gas efficiency perspective, nitrogen is an inert gas with stable thermal expansion properties, making it less prone to explosions, thereby greatly lowering the risk of blowouts. It also helps inhibit the spontaneous combustion of gases released by rubber tires, preventing self-ignition. Reasons for insufficient car tire pressure: Leakage from the tire or valve stem, which requires inspection at a tire shop. Air leakage caused by punctures from nails or other hard objects while driving, leading to insufficient pressure. The most critical factor in tire maintenance is proper inflation. Neither the tire nor the inner tube can be completely airtight. To avoid the dangers of underinflation, the air lost from the tire must be replenished.
13
0
Share

Is the Opening Date of the Jitai Expressway October 30th?

The Jitai Expressway officially opened on October 27, 2020. Constructed and invested in by China Energy Engineering Group Gezhouba, the Jinan to Tai'an Expressway was fully completed and opened to traffic, marking the full operation of the Jitai Expressway. This development establishes a new half-hour direct route between Jinan and Tai'an. After its opening, social vehicles were allowed to use the expressway after 12:00 noon. The Jitai Expressway is a crucial component of Shandong Province's expressway network. It starts at the intersection of Jinan's Ring Expressway and the southern extension of the Second Ring East Road and ends in the northeastern part of Culai Town in Tai'an, connecting with the Taixin Expressway. The total length of the expressway is 55.9 kilometers, with a mainline designed as a six-lane, two-way expressway and a speed limit of 120 km/h. The project includes six tunnels and 65 bridges along the mainline, making it one of the few expressways in the province with a tunnel cluster, with a bridge-tunnel ratio of approximately 50%.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.