How to Turn Off the Rear Wiper on an Old Ford Focus?

3 Answers
DelMadeline
07/24/25 7:16pm
The rear wiper switch is located on the knob on the side of the wiper control lever. Press it to the O position to turn off the rear wiper. Here is some relevant information: 1. Wiper Function: The wiper is an important accessory installed on the windshield. Its function is to clear rain, snow, and dust from the windshield that obstruct the view. Therefore, it plays a crucial role in driving safety. If the wiper blade does not clean effectively, remove it, soak it in water, lightly sand it with fine sandpaper, then clean and reinstall it. 2. Precautions: When using the wiper to remove dust from the windshield on sunny days, always spray windshield washer fluid and avoid dry wiping. For other stubborn or hard contaminants on the glass, clean them manually. These substances can easily damage the wiper blade, causing it to clean poorly. In severe cases, the wiper motor may also be affected.
Was this review help?
13
1
Share
StCassandra
08/10/25 8:55am
Last time I drove my old Focus, the rear wiper was quite annoying, but turning it off isn't actually complicated. There's a dedicated knob or paddle on the wiper stalk (on the right side of the steering wheel) that controls the rear wiper - the exact design depends on the model year. At the end of the stalk, you just need to gently twist it or push it back to the center position to turn it off. I remember the old Focus had an automatic feature where the rear wiper would activate when reversing; in that case, manually switch it back to 'off' after shifting gears. Avoid fiddling with the switch unnecessarily to prevent dust buildup and jamming. If it won't turn off, check the wiper fuse in the fuse box - it might be blown. Alternatively, wipe the switch contacts with a damp cloth and keep them dry to prevent short circuits. Maintaining the wiper system extends its lifespan and prevents distractions during rainy drives that could compromise safety. Just take it step by step, no need to rush.
Was this review help?
3
0
Share
Expand All
MacCaroline
09/26/25 3:50am
I've been commuting with my old Ford Focus for years, and the rear wiper switch is quite simple. The wiper stalk is located on the right side of the steering wheel. Find the section that controls the rear wiper, usually a small tab or rotary knob at the end. To turn it off, simply return it to the middle or the position marked 'off'; some cars activate it when reversing, so just adjust it before driving. The switch might be loose or dusty—give it a few gentle taps to secure it. To prevent accidental activation, regularly clean the windshield and wiper arms. If it still won't turn off, check the manual or ask a friend for help. Safety first—avoid prolonged wiper use to save battery and prevent distraction, especially when driving steadily on highways for peace of mind.
Was this review help?
19
2
Share
Expand All
More Forum Discussions

How to reset the oil change reminder on the Civic dashboard?

Civic dashboard oil change reminder reset steps are as follows: 1. First, do not start the car, locate the setup button below the dashboard. 2. Find the maintenance light reset button on the right side of the dashboard, then start the Civic while continuing to hold the button for about ten seconds until the maintenance interval indicator enters reset mode. 3. Release the reset button and press button A within 20 seconds. 4. Additional information: The "SERVICE" display is the maintenance interval indicator. When the ignition switch is in the "ON" position, the "SERVICE" display will flash. If the indicator disappears after starting the engine, it means the vehicle requires maintenance.
16
4
Share

What are the reasons for unstable CarPlay connection in the Mazda3 Axela?

There are many reasons for unstable CarPlay connection in the Mazda3 Axela. Data cable connection issues: This is a common problem for many car owners. Over time, the data transmission function of the cable may fail, causing it to only charge but not transfer data. In this case, you need to purchase a new data cable, preferably an original one or an MFI-certified cable. Alternatively, you can use a one-male-to-two-female data cable to connect your phone. USB port issues: Frequent plugging and unplugging of the data cable can lead to a loose USB port, poor contact, or even damage. Check if these are the causes. If not, also verify if the USB port's current is too low. Insufficient current can cause intermittent disconnections, where re-plugging the cable temporarily restores the connection. If this is the issue, you may need to increase the USB port's current or use a one-male-to-two-female data cable with one end connected to a power bank. Outdated iOS version on the phone: First, check if the phone's operating system is outdated. An older version may cause unstable connections, so updating to the latest version is recommended. Additionally, if the phone hasn't been restarted for a long time, this could also lead to connection issues. Regularly restarting the phone can help maintain stable CarPlay functionality. Insufficient phone memory: If the phone's memory is low, the CarPlay function may experience lag or disconnections when processing larger data. Clearing the phone's memory and ensuring sufficient space is available can help the CarPlay function run smoothly. Also, make sure all relevant permissions for CarPlay are enabled on the phone to ensure a stable connection.
6
4
Share

What is the throttle reset method for Camry?

Camry throttle reset method is as follows;1. First, turn the key to the power supply position, but do not start the vehicle engine, that is, in the off state. 2. Then, after standing for about 10 seconds, quickly press the accelerator pedal to the bottom, be sure to press it quickly to the bottom, hold for 15 seconds, and then quickly release the pedal. 3. After that, turn off the key door, pull out the key, and stand for about 15 seconds. 4. Finally, start the vehicle normally, and the reset is complete. Extended information: The electronic throttle has a self-adjustment function, and reset is generally required after cleaning or replacement. The function of the throttle is to specifically input air into the engine and discharge the exhaust gas after combustion.
14
2
Share

How tall is the BMW X3?

The BMW X3 has a body length of 4717MM, a width of 1891MM, a height of 1689MM, and a wheelbase of 28654MM, with improved dimensions compared to the previous model. The new BMW X3 features more extended side body lines than the current model, with a waistline that runs from the front fender to the taillights. Here is some related information about the BMW X3: 1. Powertrain: It is equipped with a 2.0T-L4 engine, featuring turbocharged intake, with a maximum horsepower of 184ps and a maximum torque of 290nm. 2. Configuration: The BMW X3 is a front-engine, four-wheel-drive vehicle. It has a double-joint shock absorber front suspension and a multi-link independent rear suspension. The steering assistance type is electric power, and the body structure is of a load-bearing type.
18
4
Share

What is the maintenance interval for the Buick LaCrosse?

Buick LaCrosse maintenance interval is 5,000 kilometers. The following is an introduction to car maintenance: 1. The purpose of car maintenance is to keep the vehicle clean, maintain normal technical conditions, eliminate potential hazards, prevent failures, slow down the deterioration process, and extend the service life. 2. Car maintenance mainly includes the engine system (engine), transmission system, air conditioning system, cooling system, fuel system, power steering system, etc. 3. Minor maintenance generally refers to the regular maintenance items performed at the manufacturer's specified time or mileage to ensure vehicle performance after the car has traveled a certain distance. It mainly includes changing the engine oil and oil filter.
5
0
Share

How to reset the maintenance wrench on the Besturn X80?

Besturn X80 maintenance wrench reset steps are as follows: 1. Turn the ignition switch to the "OFF" position, and hold down the "OK" button on the dashboard without releasing it. 2. Turn the ignition switch to the "ON" position, keep pressing the "OK" button for more than 10 seconds; after releasing the "OK" button, the maintenance light will reset. Below is an introduction about car maintenance: 1. Major maintenance refers to the routine maintenance performed at the time or mileage specified by the manufacturer, including replacing the engine oil, oil filter, air filter, gasoline filter, etc. 2. Minor maintenance mainly includes replacing the engine oil and oil filter.
9
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.