···
Log in / Register

How to turn off the rear wiper of Audi Q5?

3 Answers
Arlene
09/08/25 6:04am
The rear wiper is mainly located at the middle and lower end of the rear car window, and the wiper control lever is positioned on the lower right side of the steering wheel. Push the wiper lever to the "OFF" position to turn off the rear wiper. Pushing the wiper control lever down one gear is the operation to turn on the rear wiper. The control gear of the front wiper can be appropriately adjusted according to the gear of the wiper control lever.
Was this review help?
6
2
Share
DelJosie
09/20/25 4:40am
I've been driving an Audi Q5 for several years, and turning off the rear wiper is actually quite simple. The main operation involves the wiper stalk on the right side of the steering wheel, which has a rotary knob specifically for controlling the rear wiper. When you don't want to use it, rotate the knob counterclockwise until you hear a click, and it will stop completely. Some models require pressing the button at the end of the stalk. It usually turns on automatically when it rains, but turning it off after the rain stops can save water in the reservoir and extend the wiper blade's lifespan. Remember, operating it while driving is distracting, so adjust it when parked or moving slowly. When I first got the car, I was a bit confused, but reading the manual for a few pages helped—Audi's design is quite intuitive. Develop a habit of checking the wiper's status to prevent it from activating unintentionally, avoiding unnecessary resource waste like wiping in the garage.
Was this review help?
3
5
Share
Expand All
StWalter
11/03/25 5:02am
The rear wiper system of the Audi Q5 is electronically controlled, and the key to turning it off lies in the position of the stalk knob. Rotate the knob to select the OFF mode, and the rear wiper will stop immediately. During daily use, I noticed that the system relies on a rain sensor, but you can manually turn it off when automatic function is not needed. This design protects the circuit, preventing excessive wear or power consumption. If the stalk occasionally feels unresponsive, check for looseness or accidental button presses. Always prioritize safety and avoid operating it at high speeds. Understanding automotive electronic principles makes it easier to master. Turning off the rear wiper is crucial during car washes to prevent the blade from scratching the rear window glass.
Was this review help?
20
0
Share
Expand All
More Forum Discussions

Does a car belong to the category of passenger vehicles?

A car does not belong to the category of minibuses. Below is the classification of vehicles: 1. Minibus: A minibus refers to a passenger vehicle used for transporting passengers, with seating capacity not exceeding 16 seats excluding the driver's seat. In China, it commonly refers to passenger vehicles with a length greater than 3.5m but less than or equal to 7m, and a manufacturer's specified maximum total mass greater than 3.5t but less than or equal to 7t. According to the Chinese national standard "Classification of Power-driven Vehicles and Trailers" (GB/T15089-2001), which aligns with international standards, such passenger vehicles are defined as those with more than 8 passenger seats and a maximum total mass not exceeding 5t. 2. Family car: A family car, also known as a private car or personal car, is generally privately owned and used by families for commuting, holiday trips, shopping, and can also be used for business activities when needed. Since the expenses of a family car are borne by the family, they are directly related to the family's income level. Generally speaking, most family cars are of a lower grade than public or commercial cars, with lower purchase prices and maintenance costs.
20
4
Share

What are the driving tips on highways?

Here are some driving tips for highways. 1. Speed limit: Before entering the highway, set a speed limit for yourself. It is recommended that beginners maintain a speed of 90-100 km/h under normal road conditions. 2. Check carefully before overtaking: Especially when overtaking large trucks, you must first turn on the turn signal, honk the horn continuously, and if necessary, flash the high beams to signal, ensuring the vehicle ahead understands your intention to overtake. 3. Maintain a safe distance: Keep a following distance of 100 meters. There are constant distance confirmation signs on the highway to help estimate your following distance. Try to avoid driving behind large trucks for extended periods, as their large size blocks the view ahead. Additionally, some trucks have dim taillights, which can pose hidden dangers.
11
1
Share

How far can a run-flat tire travel with low pressure?

Generally speaking, even when maintaining a speed of 80km/h with no tire pressure, the run-flat tire can still travel nearly 80 kilometers. Here is a related introduction to the advantages of run-flat tires: 1. Support and resilience: Run-flat tires have more support and resilience in the sidewalls compared to regular tires, so in the event of sudden air loss or a blowout, the rim and tire can work together to support the vehicle, reducing the danger. In contrast, if a regular tire experiences a sudden blowout or air loss, it relies solely on the rim to make contact with the ground, lacking the support of the tire, as regular tires tend to detach from the rim when they lose pressure. 2. No immediate air loss: Due to the unique construction of run-flat tires, they do not immediately lose all air when a blowout occurs, allowing the vehicle to continue driving for a certain distance even with air leakage. 3. Durability: Run-flat tires have reinforced sidewalls, which inherently enhances their durability, making them more long-lasting than regular tires.
16
4
Share

Is there a problem with the front tire pressure of 230 and rear tire pressure of 210 for the X-Trail?

The front tire pressure of the X-Trail being 230 and the rear tire pressure being 210 is slightly low for the rear tires, as the standard tire pressure for the Nissan X-Trail is between 2.2-2.5 bar. Solutions for insufficient tire pressure: If no damage is visible, you can directly inflate the tires to the normal pressure and reset the tire pressure system; If a puncture is found upon inspection, drive to a tire shop promptly for a repair and then reinflate the tire; If the tire pressure warning reappears some time after inflation without any punctures, it might be due to air leakage caused by a deformed wheel rim. It is advisable to check the wheel rim and replace it if necessary. There are three common methods for tire pressure monitoring: Direct Tire Pressure Monitoring: This system uses pressure sensors installed in each tire to directly measure the air pressure. The data is transmitted wirelessly from inside the tire to a central receiver module, which then displays the pressure for each tire. The system automatically alerts the driver if the tire pressure is too low or if there is a leak. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that tire to become smaller, making it rotate faster than the other tires. By comparing the rotational speed differences between tires, the system monitors the tire pressure. Indirect tire pressure monitoring systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Tire Pressure Monitoring System (TPMS) Overview: This system combines the advantages of both the direct and indirect systems. It equips two diagonally opposite tires with direct sensors and includes a four-wheel indirect system. Compared to a fully direct system, this hybrid system can reduce costs and overcome the indirect system's inability to detect simultaneous low pressure in multiple tires. However, it still cannot provide real-time pressure data for all four tires as a fully direct system can.
7
2
Share

What Are the Different Gear Positions in a Car?

Below is an introduction to the various gear positions in a car: 1. P——Parking, Parking Gear. When the car is parked and not in use, the gear is in this position, where the wheels are mechanically locked to prevent rolling. 2. R——Reverse, Reverse Gear. 3. N——Neutral, Neutral Gear. Used for temporary stops (e.g., at a red light). This position indicates neutral gear. To prevent the car from rolling on a slope, the brake must be engaged. 4. D——Drive, Drive Gear, also known as the driving gear. 5. 2——Second, Low Gear. This gear is used when starting on a steep slope or a significantly inclined surface. The principle is that placing the gear in this position restricts the car's gear shifts to only low gears (equivalent to first and second gears in a manual transmission car), ensuring maximum forward momentum. 6. L——Low, Low Gear. When descending a mountain or a long slope, placing the gear in this position restricts the car's gear shifts to the lowest gear (equivalent to first gear in a manual transmission car). This allows the car to use engine braking during descent, preventing the driver from having to press the brake for extended periods, which could overheat the brake pads and pose a danger. 7. OD——OverDrive, Overdrive Gear.
3
0
Share

What is the standard adjustment for car headlights?

The adjustment of car headlights usually involves the left-right and up-down alignment of the high and low beams. This can be done by using the knobs at the back of the headlight assembly with appropriate tools. The standard for left-right adjustment of car headlights is as follows: 1. The light beam of car headlights should be as concentrated as possible. Excessive dispersion can cause blurring, affecting illumination and potentially disturbing other drivers. There are two adjustment screws at the back of the headlight assembly—one for height and one for width—which can be turned to adjust the left-right and up-down alignment. If the light beam is not concentrated, left-right adjustment is necessary. 2. Park the car 10 meters away from a wall, measure the distances from the low beam to the central axis, the high beam to the central axis, and the low beam to the ground. Then move close to the wall and mark these measurements on the wall. Observe whether the light beam is offset left or right or too high or low. If the focal point of the headlight does not align with the marked point, it indicates misalignment. Adjust the width knob to align the focal point with the mark on the wall. 3. Generally, the width of the light beam is preset at the factory and is not recommended for self-adjustment. If there is misalignment, minor adjustments can be made. During adjustment, the right headlight beam can be slightly tilted to the right to improve visibility of the right-side road in low-visibility conditions like rain or fog. However, it is more advisable to have the adjustment done professionally at a 4S shop or repair shop.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.