How to Turn Off the Overhead Light in a Buick?

2 Answers
StHazel
07/24/25 7:38pm
The car will automatically turn the headlights on or off based on the surrounding environment, or you can turn the knob to the far left to manually turn off the headlights. The Buick Excelle's reading light has two main modes: one is the constant-on mode, and the other is the DOOR mode. When the DOOR mode is activated, the reading light will turn on when the door is opened and turn off when the door is closed.
Was this review help?
13
4
Share
AngeloDella
08/11/25 10:48am
The light on the ceiling of a Buick is usually the roof reading light, and there are several simple ways to turn it off. The most common method is to directly press the switch button on the lampshade, which is generally found near the light. Most Buick models have ceiling light switches with three modes: always on, on when the door opens, and off. Simply press the button to switch to the off mode. If you can't find the button, don't worry—check the overhead light control area near the center console. Some Buick models have a dial switch above the air conditioning panel. If all else fails, wait for it to turn off automatically; it will shut down after more than 10 minutes of inactivity. Be careful not to block the light sensor near the rearview mirror, as this can cause the light to stay on and drain the battery. If you still can't find the switch, consulting the manual is the most reliable option, as the location may vary between models. For example, my LaCrosse has a different design compared to the Excelle.
Was this review help?
16
4
Share
Expand All
More Forum Discussions

What to Do When the Car Remote Fails to Start the Engine?

Locate the power wire of the anti-theft device and remove its fuse; Follow the thin yellow wire on the anti-theft device to find a power-cut relay; Remove the power-cut relay, then reconnect the original car wires to restore the original wiring.
20
5
Share

How to Sew a Steering Wheel Cover?

First, after starting the stitch, don't rush to sew immediately. Begin with edge tucking by using an insertion tool to push the leather into the gaps. Only start sewing after everything is properly aligned. Regarding the tension, moderate force is sufficient as long as the stitching positions are aligned. At the beginning, there's no need to pull the thread too tight. After sewing a section, you can use a small flat-head screwdriver to tighten the thread before continuing. After completing all stitches and tying the knot, the entire steering wheel cover is sewn. Adjust the lighter flame to high and quickly pass it over the stitched area twice to burn off any frayed edges of the thread.
4
2
Share

How to Repair Wheel Rim Wear?

Carefully sand the worn area of the wheel rim until it becomes smooth, then use metal filler to level the sanded scratches; After filling with the filler, use fine sandpaper to re-sand any uneven areas; Once the secondary sanding is complete, proceed to paint the wheel rim; After the primer is baked dry, apply a layer of clear coat for protection, and then place it back into the baking chamber for high-temperature curing; Once the wheel rim paint is baked dry, use a polishing machine to polish the surface for a more attractive finish.
19
3
Share

How to Open the Trunk from Inside the Regal?

Long press the button on the key other than "Lock" or "Unlock" to open the trunk from inside the car. There is a trunk release button on the door trim panel of the driver's side in the Buick Regal. Press and hold it for more than 3 seconds to open the trunk. Pull the emergency release handle firmly to open the trunk.
4
2
Share

How to Perfectly Fix Water Leakage Above the Car Door?

Thoroughly grind the worn area of the wheel hub until it becomes smooth, then use metal body filler to level the grinding marks on the wheel hub; After using the body filler for leveling, use fine sandpaper to grind any uneven areas again; Once the secondary grinding is completed, you can proceed to paint the wheel hub; After the primer is baked dry, apply another layer of clear coat for protection, and finally place it back into the baking room for high-temperature baking; Once the paint on the wheel hub is baked dry, to make the wheel hub's appearance more attractive, you can polish it using a polishing machine.
18
1
Share

How to Install a Motorcycle Trunk?

Fix the iron plate onto the motorcycle's rear rack using screws. Place the trunk on the installed iron plate and secure it with bolts. Generally, multiple bolts are required to ensure it is firmly fixed. Check the stability and confirm the installation is complete.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.