How to Turn Off the Mirror Light?

1 Answers
VanLouis
07/29/25 12:34pm
The method to turn off the mirror light is: 1. The small light on the exterior rearview mirror is a turn signal, which can be turned off using the light control switch; 2. Some lights under the rearview mirror are position lights, which are automatically illuminated and cannot be manually turned off; 3. If the windows are not closed when locking the car, the small lights under both rearview mirrors will remain on. Closing the windows or unlocking the car will turn them off within 30 seconds to one minute. The rearview mirror is a tool for the driver to directly obtain external information about the rear, side, and lower parts of the car while seated in the driver's seat. Its purpose is to facilitate the driver's operation, prevent traffic safety accidents, and ensure personal safety.
Was this review help?
10
2
Share
More Forum Discussions

How often should a car be driven when parked for long periods?

Cars should ideally be driven at least once a month under normal circumstances; for vehicles aged 4-5 years, it's recommended to drive them at least once a week. Prolonged parking can lead to tire aging, deformation, and battery drain. Therefore, it's best not to leave a car unused for too long; driving it for about half an hour every week is advisable. Below are some daily maintenance tips for cars: 1. Check the engine oil level: When the engine is cold, remove the dipstick, wipe it clean, reinsert it fully, then pull it out to check. The oil level should be between the upper and lower marks. For a hot engine, turn it off and wait until all the oil has drained back into the oil pan before measuring. 2. Check the coolant level: When the engine is cold, the radiator should be full, and the level in the expansion tank should be between the marked lines. When the engine is hot, the coolant level should be slightly above the upper mark.
4
1
Share

Is It Necessary to Clean the Exterior of the Engine?

Cleaning the exterior of the engine is necessary. The purposes of cleaning the engine exterior are: 1. To keep the vehicle clean and tidy; 2. To reduce the damage caused by corrosive substances to various components of the engine exterior, thereby extending the lifespan of the engine parts; 3. To prevent dust and impurities from entering the engine compartment and forming carbon deposits and gum on the engine surface; 4. To avoid accelerated aging of wiring and rubber components; 5. To prevent engine damage caused by various oxidation processes. Methods for engine maintenance include: 1. Using high-quality engine oil; 2. Using qualified coolant; 3. Regularly cleaning scale from the radiator; 4. Periodically removing carbon deposits from the car; 5. Replacing the car's three filters on time; 6. Maintaining a reasonable engine speed.
16
0
Share

What does the SE light mean?

This is the maintenance indicator light of the car. When this light comes on, the owner must immediately go to the 4S shop for maintenance. Regular maintenance is crucial for the car. If the car is not maintained on time, it will affect the performance of the car. Maintenance mainly involves replacing the wearing parts and fluids. Extended information: 1. The wearing parts of the car include engine oil, transmission oil, coolant, differential oil, power steering oil, and brake oil. Engine oil is called the blood of the engine. If there is no engine oil in the engine, the engine cannot run normally. Engine oil not only lubricates the engine but also cleans, seals, buffers, prevents rust, and dissipates heat. 2. When the engine is running, the engine oil forms an oil film on the surface of each part of the engine, which can prevent direct contact and friction between the parts. If the parts directly contact and cause friction, it will increase the wear of the engine and also cause a large amount of heat to be generated instantly in the engine, which is a fatal risk for the engine.
10
0
Share

Can an Electric Vehicle with Lead-Acid Battery Use Lithium Battery?

It is not advisable to replace a lithium battery with a lead-acid battery. For electric vehicles, it is best to use the original lithium battery or lead-acid charger that comes with the vehicle. Using mismatched chargers can cause significant damage to the battery and may also lead to safety hazards. Additional Information: 1. When replacing a lithium battery with a lead-acid battery, it is essential to ensure that the voltage remains the same as the original lithium battery. Additionally, the charger must be replaced with a dedicated lead-acid battery charger. Improper installation or poor-quality lead-acid batteries may damage the controller. 2. When replacing a lithium battery with a lead-acid battery, the size of the battery compartment must also be considered. Generally, lithium battery compartments are relatively small, while lead-acid batteries are larger. This factor must be carefully considered before replacement. If the gap is too small after installation, the battery may not fit. If you decide to proceed with the replacement, it is recommended to consult an electric vehicle repair shop and have it installed by professionals.
16
1
Share

Should New Cars Undergo Crystal Coating?

It is necessary. Once a new car leaves the production line, its paint surface begins to react with the air and oxidize. Over time, the paint deteriorates and loses its luster. Applying crystal coating to a new car can slow down the oxidation of the car's paint surface and help maintain its glossy appearance. Below are the benefits of crystal coating: 1. Enhanced corrosion resistance: After crystal coating, the car's surface is isolated from the external environment, making it less susceptible to oxidation by air and effectively preventing acid rain from corroding the paint surface. This significantly extends the lifespan of the car's paint. 2. Easier cleaning: The car's surface becomes as smooth as ceramic tiles after crystal coating. During routine car washes, simply rinsing with water can easily remove dust, mud, and other debris from the surface. 3. Scratch resistance: Crystal coating reduces damage from external forces to the car's surface. Any scratches will only affect the crystal layer, not the car's paint or primer, preventing severe damage.
20
3
Share

How is the SAIC dry dual-clutch transmission?

SAIC's dry dual-clutch technology is quite mature, but there are some minor issues. The SAIC dry dual-clutch transmission may experience severe overheating when frequently shifting between first and second gears in traffic jams. The driving techniques for dry dual-clutch transmissions are as follows: 1. Light throttle and gentle start: The gentle start is because the original design allows the dual-clutch to output maximum torque in second gear, while first gear lacks sufficient power. Therefore, you should wait until the throttle smoothly transitions to second gear before pressing the accelerator further. 2. Shift to neutral when parking: The principle of the dual-clutch is similar to that of a manual transmission. When parking, the clutch is not completely disengaged. Due to the purely mechanical connection principle, when the brake is pressed for a long time with the gear engaged, the energy has nowhere to go, causing some wear on the clutch disc.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.