How to turn off the Magotan?

Is a tire temperature of 60 normal in summer?

Tire temperatures between 90-110 degrees Celsius are considered normal, and a tire temperature of 60 degrees is not a cause for concern. Tires are equipped with insulation sleeves that generally keep the temperature within a controllable range. Additionally, excessively high tire temperatures can be very dangerous. Here are some methods to prevent car tire blowouts: Maintain normal tire pressure: Manufacturers provide standard tire pressure values, which should not be too high or too low. High pressure can easily lead to blowouts, while low pressure can also cause blowouts when the tire temperature rises. It is recommended to use tires of the same model and tread pattern for the vehicle: Especially, the front two wheels and rear two wheels should not use different types of tires. Regularly inspect tires: Repaired tires should not be used as front tires. Tires with tread crowns punctured by hard objects over 5mm, side punctures, tread depth below 1.6mm, or cracks and damages at the bead should be replaced promptly. Check the tread: Look for embedded stones or foreign objects. Ensure the spare tire maintains proper pressure. Use a pry bar to tap the tire—if the sound is crisp or the rebound is good, it's fine; if the sound is dull, inflate it promptly.

13

5

Share

Start the Engine First or Depress the Clutch?

Depress the clutch first before starting the engine. Below is relevant information about the clutch: Clutch: The clutch is located within the flywheel housing between the engine and the transmission. The clutch assembly is secured to the rear plane of the flywheel with screws, and the output shaft of the clutch serves as the input shaft of the transmission. While driving, the driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine and transmission, thereby cutting off or transmitting the engine's power to the transmission. The principle of releasing the clutch: The principle of releasing the clutch is: 'Slow at first, quick in the middle, and coordinated at the end.' When initially depressing the pedal, do it quickly and press it all the way down in one motion. When lifting the pedal, move quickly during the free travel phase, slow down as it nears engagement, pause slightly at the semi-engagement point, and then release it completely. The key to this process is accurately identifying the semi-engagement point. To control the vehicle speed effectively, treat the semi-engagement point as the dividing line—lifting quickly above it and lowering slowly below it, adjusting downward to select a speed that suits you.

2

3

Share

What is the difference between 3-cylinder and 4-cylinder engines?

The differences between 3-cylinder and 4-cylinder engines: 1. Manufacturing structure: The 3-cylinder turbocharged engine has a simpler manufacturing structure, is smaller in size than a 4-cylinder engine, and is lighter in weight. 2. Acceleration: The 4-cylinder turbocharged engine performs better in terms of starting and acceleration, and its stability is superior to that of the 3-cylinder engine. 3. Operation state: The 3-cylinder engine operates in an unbalanced state, making it more prone to vibration compared to the 4-cylinder engine. 4. Noise: The 3-cylinder engine is louder than the 4-cylinder engine, and despite the use of balance shaft technology, the issue remains unresolved. 5. Displacement: 4-cylinder engines are typically used in cars with a displacement of 1.3L or more, offering greater displacement and naturally more horsepower compared to 3-cylinder engines.

20

2

Share

How to Determine if a Vehicle is China 5 or China 6?

Methods to distinguish between China 5 and China 6 vehicles mainly include the following: 1. Query on the Motor Vehicle Environmental Protection Website; 2. Inquiry at the Vehicle Management Office; 3. Check the vehicle's environmental protection label; 4. Review the vehicle's factory certificate. Additional information: 1. China 5 and China 6 refer to standards established to implement the Environmental Protection Law of the People's Republic of China and the Air Pollution Prevention and Control Law of the People's Republic of China, aiming to prevent pollution from the exhaust of compression-ignition and gas-fueled ignition engine vehicles, protect the ecological environment, and safeguard human health. 2. The differences between China 5 and China 6 include: (1) Different implementation times: China 5 standard was implemented in December 2017; China 6 standard was implemented in December 2014. (2) Different sulfur content limits: China 5 standard stipulates no more than 10mg per kilogram; China 6 standard stipulates no more than 50mg per kilogram.

9

4

Share

Is a tire pressure of 3.0 normal in summer?

Summer tire pressure of 3.0 is not normal. According to the provisions and requirements of the international GBT2978-2008 standard, the standard tire pressure is 2.4-2.5bar. 3.0bar is higher than the maximum value of the standard tire pressure, so it is not normal. Hazards of excessive tire pressure: The friction and adhesion of the tire will decrease, affecting the braking effect; It will cause steering wheel vibration and deviation, reducing driving comfort; Accelerate the local wear of the tread pattern in the center of the tire, reducing the tire life; The vibration of the car body increases, which indirectly affects the life of other parts; It will cause excessive extension and deformation of the tire cord, reducing the elasticity of the tire body, and increasing the load on the car during driving; The puncture resistance performance decreases. When encountering sharp objects such as nails and glass on the road, it is easy to penetrate the tire, and the impact will cause internal cracks and explosions, leading to a flat tire.

11

1

Share

Is the Leiling 1.2T model a hybrid?

The Leiling 1.2T model is a pure gasoline-powered vehicle. The Leiling is a compact sedan under the Toyota brand. The Leiling's 1.2-liter turbocharged engine is a four-cylinder engine with a maximum power output of 85 kW and a maximum torque of 185 Nm. This engine features VVT-iW technology and direct fuel injection, and it utilizes an aluminum alloy cylinder head and block. The engine reaches its peak power at 5,200 to 5,600 rpm and its peak torque at 1,500 to 4,000 rpm. It is paired with a CVT transmission. The use of a CVT transmission enhances the vehicle's fuel efficiency and shift smoothness. CVT transmissions are commonly found in Japanese cars and have a relatively simple structure. Inside the CVT transmission, there are only two pulleys and a steel belt. The steel belt can move along the pulleys, allowing the transmission to vary speed and torque. The Leiling 1.2T model features a MacPherson independent front suspension and a multi-link independent rear suspension. The multi-link suspension improves the car's handling and ride comfort.

6

3

Share

How to turn off the Magotan?

Is a tire temperature of 60 normal in summer?

Start the Engine First or Depress the Clutch?

What is the difference between 3-cylinder and 4-cylinder engines?

How to Determine if a Vehicle is China 5 or China 6?

Is a tire pressure of 3.0 normal in summer?

Is the Leiling 1.2T model a hybrid?

What is the difference between 1.6T and 2.0T?

What is the Mustang car?

Will There Be Any Impact If a Car Is Not Driven for a Month in Summer?

What is the fuel tank capacity of the NV200 in liters?