How to Turn Off the Lights When the Car Is Not Turned Off at Night?

2 Answers
AndresDella
09/03/25 7:49am
To turn off the car lights, simply rotate the light control knob to the "OFF" position (some models may have the "O" position for turning off). Simply press to turn off. For some models, the light control is on the light lever, and you just need to rotate the lever to turn off the lights.
Was this review help?
15
1
Share
McRuth
09/16/25 2:25am
When I first started driving, I also made silly mistakes like leaving the engine running and the lights on at night, which were glaring. Generally, you can find a small lever on the left or in the middle of the steering wheel, turn it to the OFF position, and the lights will go out. The engine running doesn't affect this operation. If the lights have buttons on the dashboard, pressing them will also turn them off neatly. Saving power is key, especially when parking for a while to avoid draining the battery, but be careful when turning off the headlights in pitch-dark sections for safety, leaving some position lights to remind others to pay attention. The location of the light switches varies by car model, such as thicker levers in SUVs and lighter buttons in compact cars. Remember to turn off the lights to extend battery life, a small act of safety and consideration, and you'll get used to it after practicing a few times.
Was this review help?
17
0
Share
Expand All
More Forum Discussions

How to Turn on the Rearview Mirror Heating for the 10th Generation Accord?

To activate the rearview mirror heating function for the 10th Generation Accord, simply press the rearview mirror heating button located near the driver's seat. The rearview mirror heating feature is particularly useful during rainy or snowy weather. Once activated, the heater behind the mirror quickly warms the surface, effectively removing water droplets or fog from the rearview mirror, thereby reducing driving hazards to some extent. The 10th Generation Accord is a vehicle launched by GAC Honda, equipped with a V6 3.0L engine that utilizes i-VTEC and an intelligent power management system. This system can automatically switch between 3-cylinder and 6-cylinder operation modes based on actual road conditions.
4
4
Share

What is the Toyota Aqua called in China?

Toyota Aqua is called Prius in China. The following is an introduction to the Prius: 1. Vehicle Overview: The Toyota Prius, launched by Toyota Motor Corporation of Japan in 1997, was the world's first mass-produced hybrid vehicle model. It was subsequently sold to more than 40 countries and regions worldwide in 2001, with its largest markets being Japan and North America. 2. Design Philosophy: Before the energy crisis and environmental issues became prominent, TOYOTA foresightedly incorporated hybrid technology development into its long-term plans. After over 40 years of dedicated effort, the Prius was the first to perfectly execute avant-garde design concepts with future-oriented craftsmanship, and it also led the era by incorporating a series of highly intelligent technologies.
13
1
Share

Why is there a strange noise when shifting into P gear?

Shifting into P gear with a strange noise is the sound of gear engagement, which is a normal phenomenon. Here are some introductions about P gear: 1. The "P" in P gear comes from the first letter of the English word Park, so in the gear positions of automatic transmission cars, P gear is the identifier for the parking gear. 2. P gear is a gear evolved from N gear. In addition to putting the transmission into neutral mode, it also has a pawl inside the transmission that locks the gear on the output shaft to form a mechanical lock, thereby securing the drive axle to fix the vehicle in a stationary or slightly moving state.
18
3
Share

What are the symptoms of a damaged steering tie rod ball joint in a car?

Balance rod ball joint damage can cause noise when driving on rough roads, but no abnormal sounds will occur when driving on paved roads. The related introduction of the balance rod is as follows: Balance rod suppresses body roll: When the left and right wheels of a car pass over different road bumps or potholes, anti-roll resistance (Roll-Resistance) is generated, suppressing body roll. Balance rod classification: Front lower control arm balance rod (original equipment required part), toe-in balance rod (original equipment required part), front shock tower top balance rod (commonly known as "top bar" in Hong Kong and Macau, optional part), front crossmember balance rod (commonly known as "front lower bar", optional part), etc.
13
5
Share

What is the difference between dual exhaust pipes and single exhaust pipes?

There is essentially no difference between dual exhaust pipes and single exhaust pipes. The exhaust pipe's sole purpose is to expel combustion waste gases and reduce noise. Installing dual exhaust pipes is primarily for aesthetic appeal and a more imposing appearance. The exhaust pipes of SUVs, coupes, and off-road vehicles are largely similar, differing only in quantity—some have one pipe, while others have two. Additionally, the layout of the exhaust pipes varies; some adopt a single-side dual-exit configuration, while others feature a dual-side dual-exit setup. The function of the exhaust pipe is to discharge the waste gases produced by the engine. Moreover, exhaust pipes are often designed in various shapes mainly to reduce exhaust noise and improve exhaust efficiency. Generally, high-displacement vehicles tend to have more than two exhaust pipes, as this design enhances the engine's exhaust efficiency.
1
0
Share

How Often Should Shock Absorber Top Mounts Be Replaced?

Shock absorber top mounts do not have a fixed replacement interval. Relevant information is as follows: 1. When the vehicle produces particularly loud noises when passing over bumpy roads, along with symptoms such as directional deviation or creaking sounds during stationary steering, the shock absorber top mounts should be replaced. Otherwise, it will affect both the driving experience and safety. 2. If the shock absorber top mounts and buffer rubber lose their elasticity and softness due to aging, or even become damaged, the force from the suspension's up-and-down movement will be directly transmitted to the metal structure of the vehicle body, causing noticeable impact noises. Especially when driving on uneven roads, the suspension components may produce clanking metal impact sounds. Severe damage can also shorten the lifespan of the shock absorbers.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.