How to Turn Off the Ignition in Subject Three?

1 Answers
Lane
07/29/25 6:37pm
Operation for turning off the ignition in Subject Three: Turn the key counterclockwise once to shut off the engine, and twice to turn off all power. In some places, turning off the key is not required, as the safety officer will then escort you back to the safety point. If you really need to turn off the ignition, do not turn the key twice, as this will also shut down the exam computer system. Trainees should consult their instructors in advance for specific operations and follow their instructions. Below is the sequence for parking and turning off the ignition in Subject Three: 1. Upon hearing the command: When the trainee hears the instruction to pull over, turn on the right turn signal. 2. Observe: Check the right lane conditions and pull over safely after confirming it is safe. 3. After stopping: Once the vehicle is stationary, shift to neutral, engage the handbrake, release the clutch and brake pedals, reset the lights, and turn the key to the OFF position.
Was this review help?
13
0
Share
More Forum Discussions

How to Replace the Battery in an Audi Q5L Key?

Audi Q5L key battery replacement method is: take out the mechanical key inside the remote control, then directly pry open the shell, remove the battery that needs to be replaced, and install the new battery. The car smart key is a common keyless entry system, also known as the smart key system, which consists of a transmitter, remote central lock control module, and driving authorization system control module. It can transmit infrared signals to open one or two doors, trunk and fuel tank cap, and can also control the car's windows and sunroof. The Audi Q5L has a body size of 4753mm in length, 1893mm in width, and 1659mm in height, with a wheelbase of 2908mm. The car's drive mode is front-engine four-wheel drive, with front and rear suspension types both being five-link independent suspension.
8
5
Share

What Problems Will Occur If a Car Relay Fails?

Symptoms of a damaged car relay include the starter not turning, weak starter operation, and starter freewheeling. Below are specific details about car relays: 1. Function: The basic role of a car relay is to act as an "automatic switch" that uses a small current to control the operation of a larger current. It serves functions such as automatic regulation, safety protection, circuit switching, and more in the electrical system. 2. Selection Based on Usage Environment: The usage environment mainly refers to temperature (maximum and minimum), humidity (typically the maximum relative humidity at 40 degrees Celsius), low air pressure (can be ignored if used below 1000 meters altitude), vibration, and impact. Additionally, there are requirements for packaging methods, installation techniques, dimensions, and insulation. Due to differences in materials and structures, relays can withstand varying environmental mechanical conditions. Using a relay beyond the environmental mechanical conditions specified in the product standards may damage it. Therefore, relays should be selected based on the environmental mechanical conditions of the entire machine or higher-level conditions.
15
5
Share

Where is the Evaporative Emission Control Valve Located?

Evaporative emission valve is located on the pipeline between the carbon canister and the engine intake pipe. Below is the relevant introduction about the evaporator: 1. Working principle: The evaporator vaporizes the compressed and liquefied refrigerant, changing it from liquid to gas while absorbing heat, thereby lowering the temperature of the surrounding medium and serving a cooling function. 2. Composition: The evaporator consists of one or several sets of coils. 3. Maintenance: (1) Fins: Inspect the surface of the evaporator fins. If clogged with dirt, it should be cleaned (do not use water) and blown clean and dry with compressed air. If bent or deformed, use needle-nose pliers or a screwdriver to straighten them. (2) Pipes and threaded joints: Check the pipes and threaded joints. If cracked, damaged by foreign objects or the fan, or showing cracks or scratches, they should be replaced or repaired by welding.
19
5
Share

What is the function of engine oil in a car?

Engine oil serves the following purposes: 1. Lubrication to reduce wear: There is rapid relative sliding between the piston and cylinder, as well as between the main shaft and bearing bush in the engine, which can easily cause wear. High-quality engine oil can form a sufficiently thick oil film between these two sliding surfaces, separating the relatively sliding parts to achieve the goal of reducing wear. 2. Cooling: Engine oil can carry heat back to the oil tank and then dissipate it into the air, assisting the radiator in cooling the engine. 3. Cleaning: Good engine oil can circulate carbon deposits, sludge, and worn metal particles from engine parts back to the oil tank, flushing away dirt generated on the working surfaces of the parts through the flow of the lubricating oil. During normal use, engine oil will also have a certain consumption rate, so it is necessary to regularly check the oil level and its degree of contamination.
5
4
Share

What is the remote control matching method for the Volkswagen Santana Vista?

The remote control matching method for the Volkswagen Santana Vista is: Close all doors, press the central locking button on the driver's side to lock all four doors, insert the key into the ignition switch and turn it on and off three times, then remove it. The central locking system will activate once, and then press the lock button on the remote control. If the central locking system activates again, it indicates successful matching. The Santana Vista is a model under SAIC Volkswagen's Santana brand, with body dimensions of 4687mm in length, 1700mm in width, and 1450mm in height, and a wheelbase of 2656mm. The Santana Vista inherits the classic and elegant style of the Santana brand while perfectly integrating modern design elements, such as the chrome double-bar radiator grille, stylish dashboard, light-colored wood trim, beige interior theme, and leather seats, all of which exude a refined and elegant temperament.
18
1
Share

What is the long-distance fuel consumption of the Geely Jiaji PHEV?

Geely Jiaji is equipped with a plug-in hybrid system consisting of a 1.5T engine + electric motor + battery pack, with a comprehensive maximum horsepower of 258 hp and a peak torque of 385 N·m. The battery pack capacity is 11.3kWh. It is paired with a 7-speed wet dual-clutch transmission, and the MIIT comprehensive fuel consumption is only 1.6L/100km. Relevant information about fuel consumption is as follows: 1. Introduction: Fuel consumption generally refers to constant-speed fuel consumption, which is the vehicle's fuel consumption per 100 kilometers obtained in the constant-speed driving fuel consumption test specified by national standards for certain types of vehicles. 2. Testing method: The test can be conducted on the road or on a chassis dynamometer, and then the fuel consumption per 100 kilometers is obtained through the 'flow meter method' or 'carbon balance method'.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.