How to Turn Off the Auto Start-Stop Function on Audi A4L?

1 Answers
LaMila
07/29/25 12:38pm
Audi A4L auto start-stop function can be turned off by pressing the auto hold button (marked with an 'A') next to the gear lever. More information about the Audi A4L is as follows: 1. On November 16, 2008, FAW Audi officially released the domestically produced new Audi A4L. The new Audi A4L features a completely redesigned exterior and chassis, with front and rear designs that closely resemble the Audi A5. 2. The Audi A4L is equipped with Audi's dynamic steering system, which adjusts the steering ratio based on driving speed and the selected Audi drive mode. This ensures agile handling at low speeds and stable operation at high speeds, working in close coordination with the ESP system to enhance safety. The integration of radar sensors and LED warning lights on the rearview mirrors further improves active safety during driving.
Was this review help?
16
2
Share
More Forum Discussions

Where is the coolant temperature sensor located on the Wuling Zhiguang?

The location of the coolant temperature sensor on the Wuling Zhiguang primarily depends on the vehicle model, generally found on the engine intake manifold below the gear shift panel. Here are some highlights about the Wuling Zhiguang: 1. The Wuling automobile brand embodies the spirit of hard work and self-improvement, and has now become one of the most valuable brands in China's automotive industry; 2. Both the Wuling text and graphic trademarks have been awarded China's Well-known Trademarks; 3. With the brand positioning of 'Quality Drives Life,' Wuling Motors is committed to providing outstanding products and passionate, trustworthy services to car owners, becoming a reliable assistant and close friend to Wuling vehicle users.
20
0
Share

What lights should be used when passing under an arch bridge at night?

When passing under an arch bridge at night, alternate between high and low beams, using them no fewer than 2 times. Specific instructions are as follows: When driving at night and passing under an arch bridge or through an intersection without traffic lights, you should alternate between low and high beams. During this alternation, the switching between high and low beams should not be fewer than two times, ensuring that other vehicles can better notice your presence. Additionally, when passing through such intersections, it is necessary to reduce your speed, as this enhances driving safety. Relevant information is introduced as follows: When a motor vehicle passes through sharp curves, slopes, arch bridges, crosswalks, or intersections without traffic signal control at night, it should alternately use high and low beams to signal. When a motor vehicle approaches sections that affect safe visibility distance, such as sharp curves or the top of slopes, or when overtaking or encountering emergencies, it should slow down and sound the horn to signal.
3
4
Share

What lights should be turned on when parking at night?

When parking at night, you should turn on the hazard warning flashers, clearance lights, and rear position lights, and confirm whether there are any foreign objects or pedestrians around the vehicle before parking. Precautions for driving at night: Proper use of lights: When the vehicle is moving, the most important lights to use are the low beam and high beam. On urban roads, it is sufficient to turn on the headlights, clearance lights, and rear position lights during normal driving. Do not turn on the high beam arbitrarily, as it may be considered a violation of traffic rules. When overtaking, the turn signal should be turned on 3-5 seconds in advance. Maintain a safe distance: When driving at night, the driver's visibility is not as good as during the day, and unexpected situations are more likely to occur. Therefore, the driver must pay attention to appropriately increasing the following distance and avoid overtaking to prevent collisions between vehicles. In case of unexpected situations, pull over in time and turn on the hazard lights to alert other vehicles to yield. Be cautious when meeting vehicles at night: When passing sharp turns, slopes, arched bridges, pedestrian crossings, or intersections without traffic lights at night, motor vehicles should alternately use the high and low beams to signal, then switch to low beams and reduce speed to pass slowly.
12
1
Share

What Causes Severe Engine Shaking During Startup?

Severe engine shaking during startup can be attributed to the following specific reasons: 1. Excessive carbon buildup in the throttle body, fuel injectors, or intake passages may be one of the causes. 2. When there is too much carbon deposit inside the engine, the gasoline sprayed by the cold-start injector can be largely absorbed by the carbon deposits, resulting in an excessively lean air-fuel mixture during cold starts and causing startup shaking. 3. Mechanical failures in components such as ignition coils, spark plugs, or fuel injectors, leading to cylinder misfires; low fuel pressure or cylinder pressure, resulting in insufficient power. 4. Oxidized or low-grade engine oil, primarily due to poor low-temperature fluidity, leading to inadequate cold-start protection for the engine.
14
2
Share

What Are Some Simple Methods to Remove Car Stickers?

Here are some simple methods to remove car stickers: 1. Use a household hairdryer set to the hot air setting. Direct the hot air at the sticker until the adhesive softens, then peel the sticker off the car body. 2. Dip a towel in some essential balm and rub it evenly over the sticker surface. Wait for a while, then peel the sticker off directly. 3. Use a specialized adhesive remover. Spray it on the sticker surface, then peel the sticker off directly. However, be cautious when using this method on glass with sun protection film. If the sticker is not carefully removed, residual adhesive may remain on the car body. To remove the adhesive, you can try the following methods: 1. Soak a towel in alcohol and wipe the residual adhesive area to remove it. 2. Using an eraser is also a simple method. Just rub the residual adhesive with the eraser to remove it. 3. Use some tar remover, but make sure to wear gloves to avoid skin contact with the cleaning agent.
16
1
Share

What Items Should Be Placed in a New Car?

New cars require the following items to be added: 1. Car floor mats: Car floor mats are highly practical, not only allowing you to decorate the car according to your preferences but, most importantly, providing protection. 2. Parking contact number plate: Parking spaces are becoming increasingly scarce these days, and sometimes you can't avoid parking on the roadside. In such cases, a parking contact number plate is essential. With this plate, others can quickly contact you to resolve any issues. 3. Steering wheel anti-theft lock: It's crucial to equip a new car with a steering wheel anti-theft lock, as it significantly increases the difficulty of theft. 4. Dash cam: A dash cam functions like the 'black box' on an airplane, continuously recording driving conditions and even capturing audio inside the car. Moreover, in cases of malicious fraud or traffic accidents, the footage recorded by the dash cam can serve as strong evidence.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.