How to turn off the air conditioning in Changan CS35?

1 Answers
EverettRose
07/25/25 3:10am
The air conditioning switch of Changan CS35 is located below the central control screen with an OFF button. To turn on the air conditioning, twist the OFF button to the right (red); to turn it off, twist it to the left (blue). All models of Changan CS35 are equipped with manual air conditioning, where the air volume and outlet mode are manually adjusted. The temperature is set to a fixed value manually, and the computer maintains a constant temperature based on the temperature changes detected by the sensor. The compressor can work intermittently to maintain the constant temperature effect. Changan CS35 is a compact SUV under the Changan brand, with a wheelbase of 2560 mm, and dimensions of 4170 mm in length, 1810 mm in width, and 1670 mm in height. The Changan CS35 is powered by two engines: a 1.6-liter naturally aspirated engine and a 1.5-liter turbocharged engine.
Was this review help?
9
5
Share
More Forum Discussions

What is the fuel tank capacity of the Lexus ES200 in liters?

The fuel tank capacity of the Lexus ES200 is 60 liters, as officially announced. Owners who have purchased the Lexus ES200 can also check this information on the vehicle's configuration sheet. The Lexus ES200 requires 92-octane fuel, with a fuel consumption of 7.75L per 100 kilometers. A full tank of fuel allows for a driving range of approximately 774km. During daily driving, it is essential to monitor the remaining fuel level in the tank. This is typically observed through the fuel gauge inside the vehicle. Under normal circumstances, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel mid-journey. During actual refueling, the amount of fuel added may exceed the calibrated capacity. This is because the fuel tank capacity specified by the manufacturer measures from the bottom of the tank to the safe fill level, leaving some space between the safe fill level and the tank opening. This space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is filled up to the tank opening during refueling, the actual amount of fuel added may exceed the calibrated tank capacity.
18
3
Share

Is it prohibited to drive a motor vehicle with a damaged driver's license?

It is prohibited to drive a motor vehicle with a damaged driver's license. According to Article 28 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China": Motor vehicle drivers shall not drive motor vehicles when their driver's licenses are lost, damaged, expired, or during the period when they are legally detained or temporarily suspended, or when the accumulated demerit points reach 12. Below is additional information: 1. Required materials for replacement: A recent 1-inch bareheaded photo of the driver (white background); Original and photocopy of the driver's ID card; (Damaged old driver's license) For lost driver's licenses, write a loss statement in the blank space of the ID card photocopy, and add a signature and date; "Motor Vehicle Driver's License Application Form". 2. Before the expiration: Drivers who have lost their licenses and are applying for a replacement are within the period where they have not submitted a physical condition certificate (inspection). Please bring the original ID card of the driver to first complete the driver's license inspection according to the "Driver's License Inspection Work Process", and then proceed with the replacement process according to this work process.
7
0
Share

When Does the Timing Start for Parallel Parking?

From entering the parallel parking area to exiting the parallel parking area. Timing starts as soon as the vehicle enters the parallel parking test area, and ends when the vehicle exits the parallel parking test area. The time interval must not exceed 90 seconds. Below are the precautions for the Subject 2 driving test: 1. Fasten your seat belt: Buckle up as soon as you get in the car. Remember not to fasten the seat belt backward or on the passenger side, otherwise the system will directly judge the test as a failure. Do not unfasten the seat belt at will during the entire test. 2. Adjust the seat, etc.: After getting in the car, adjust the seat, adjust the rearview mirror, fasten the seat belt, turn on the left turn signal, shift into first gear, and release the handbrake. These six steps are indispensable. Make sure all preparations are complete before starting. 3. No stopping during the process: There is no time limit for reversing into the garage, but it is important to note that stopping during the reversing process is not allowed. If the wheels remain stationary for 3 seconds, the system will judge it as stopping midway. Therefore, controlling the speed is crucial. 4. The time for hill start is 30 seconds: The time for hill start is 30 seconds, and the system will give a voice prompt every 10 seconds. Exceeding 30 seconds will directly result in a failure.
12
5
Share

How to Test a Single-Wire Oil Pressure Switch?

After the ignition switch is turned on, if the oil pressure indicator light does not illuminate, the possible causes are that the wiring harness of the oil pressure indicator has come loose, the filament has burned out, or the fuse has blown. After the engine is started, if the oil pressure reaches the specified value and the oil pressure indicator light turns on, the fault may be due to poor operation of the contact switch or a grounded wiring harness. Below are additional details: 1. Oil Pressure Range: When the oil pressure is below the specified value, the diaphragm does not exert enough force to push the spring, causing the contacts to close and the indicator light to illuminate. When the oil pressure exceeds the specified value, the diaphragm pushes the spring, separating the contacts and turning off the indicator light, notifying the driver that the oil pressure has reached the required level. Typically, the contact activation pressure ranges between 30~50 kPa. 2. Principle: The engine oil pressure sensor is designed to measure the oil pressure in the engine. It is usually screwed into an oil passage in the cylinder block. Inside the oil pressure sensor, there is a variable resistor with one end outputting a signal and the other end connected to a sliding arm that is grounded.
12
5
Share

What are the differences between the Langdong and the Elantra?

The Langdong and the Elantra have the following differences: 1. Exterior: Both models belong to Beijing Hyundai. The Elantra is a typical Korean car, and its updated exterior makes it look more youthful, which is a good change for a model that had been suffering from aesthetic fatigue. 2. Powertrain: The Elantra is equipped with a 1.6L engine featuring a CVVT continuous variable valve timing system. It delivers a maximum power of 82Kw/6000rpm and a maximum torque of 143N·m/4500rpm. The Langdong, on the other hand, comes with a 1.6L-γ engine and a 1.8L-Nu engine. The 1.6L engine produces a maximum power of 127 horsepower and a maximum torque of 155N·m. 3. Interior: The Elantra's interior features clean lines and a fresh beige color scheme, complemented by matte metal-finish panels on the dashboard and door armrests, giving it a stylish look. The plastic components on the dashboard are of decent quality, without a cheap feel. The Langdong offers two interior color options: all-black and a two-tone scheme with a darker upper and lighter lower section. The overall design is simple yet dynamic, with good material quality.
19
2
Share

Should You Shift to Neutral or Pull the Handbrake First When Driving?

Shift into gear first and then pull the handbrake. This approach helps prevent the vehicle from rolling and avoids sudden acceleration due to operational errors, which could lead to traffic accidents. Therefore, when starting the vehicle, it's essential to check the status of the handbrake first. If the handbrake has already been released prematurely, you need to press the foot brake. Here is some additional information about the handbrake and gear shifting: 1. The handbrake, also known as the parking brake, primarily provides resistance to the vehicle when parked to prevent it from rolling. Its braking force is much weaker than that of the service brake. Currently, common types of handbrakes include electronic handbrakes and mechanical handbrakes. 2. Shifting gears refers to the transmission's function of altering the torque and speed of the engine crankshaft to meet the varying demands for traction and speed under different driving conditions, such as starting, accelerating, and overcoming various road conditions. This allows the car to operate at a very low and stable speed.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.