How to Turn Off Car Wipers?

1 Answers
DeAubrey
07/30/25 12:26am
OFF is the stop working state of the front wiper, which is the off position of the car wiper. Rotate to this position to turn it off. Here are the related introductions: 1. The wiper, also known as the windshield wiper or windscreen wiper, is a device used to wipe off raindrops and dust attached to the vehicle's windshield. 2. INT is for automatic intermittent operation. Pull the lever down one notch, and the wiper will start working automatically in intermittent mode. This gear requires manual reset. 3. LO is for continuous operation. Pull the lever down one notch, and the wiper will work continuously at an automatic rate. 4. HI is for continuous high-speed operation. Pull the lever all the way down, and the wiper will work at high speed. This gear requires manual reset and is suitable for heavy rain weather.
Was this review help?
13
5
Share
More Forum Discussions

Where is the charging port of the Leiling?

The car charger of the Leiling is located in the armrest box. Here is the relevant content introduction: 1. Charging: If you are using your phone for navigation, you can charge it by connecting the cable. The passenger can also charge their phone. If you are using your phone for navigation, you can insert a one-to-two splitter into the USB port on the left side of the passenger seat. 2. Model Introduction: The Leiling is built based on the American version of Toyota's A-class car model. The American version of the model, with its sharp appearance and excellent quality, has been a best-seller in North America for many years, with sales consistently ranking first in the A-class car market. The Leiling inherits the champion genes of this model and has a very high-quality foundation. The all-new Leiling comes in two powertrain versions. The fuel version is equipped with a 1.2T-D-4T direct-injection turbocharged engine, which can output a maximum torque of 185 Nm at 1500 rpm, paired with an S-CVT continuously variable transmission that can simulate 10 speeds.
12
1
Share

Why is the fuel consumption of Infiniti QX60 too high?

The fuel consumption of Infiniti QX60 is 10.4L/100km. The reasons for the high fuel consumption of Infiniti QX60 are as follows: 1. Abnormal tire pressure: Abnormal tire pressure can also affect the fuel consumption of the car. When the tire pressure is too low or the tread is severely worn, the contact area between the tire and the road surface increases, friction increases, rolling resistance increases, and fuel consumption naturally becomes higher. 2. Excessive load: Long-term carrying of heavy objects on the vehicle will increase the weight of the vehicle, increase the driving pressure, and also increase fuel consumption. 3. Car sensor failure: This is also a main reason for the increase in car fuel consumption. When the water temperature sensor fails, the engine mistakenly thinks the car is in a cold state and will continuously send out fuel injection signals, leading to increased fuel consumption.
8
0
Share

What Causes the Peugeot 408 to Have High Water Temperature and Engine Fault?

Insufficient coolant, radiator fan malfunction, or circulation water pump failure. Below are detailed explanations: 1. Insufficient Coolant: Coolant leakage or low coolant levels can cause the engine water temperature to rise. In this case, check the coolant level. If it's low, first top it up to the appropriate level, then check again after a few days to see if the level has dropped significantly. If it has, locate the source of the leak. 2. Radiator Fan Malfunction: If the radiator fan fails, the heat generated during high-speed operation cannot be effectively transferred to the coolant, impairing heat dissipation. This leads to an increase in coolant temperature, potentially causing overheating. 3. Circulation Water Pump Failure: Pump failures can include seized bearings or damaged impellers. Seized bearings are relatively rare, while damaged impellers—such as cracked impellers or impellers loosened from the pump shaft—are more common. These issues slow down the coolant circulation, often resulting in engine overheating. Note that engine water temperature should not be too low either, as excessively low temperatures can cause incomplete combustion of the air-fuel mixture, reduced power output, poor lubrication, and increased emissions.
18
3
Share

Should Left-Turning Vehicles Yield to Straight-Going Vehicles?

Left-turning vehicles should yield to straight-going vehicles. According to Article 51, Section 7 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China": At intersections without directional signal lights, turning motor vehicles must yield to straight-going vehicles and pedestrians. Right-turning vehicles from the opposite direction must yield to left-turning vehicles. Motor vehicles passing through intersections controlled by traffic signal lights shall comply with the following rules: Enter the guiding lane in the desired direction: At intersections with marked guiding lanes, enter the guiding lane according to the intended direction of travel. Yield to vehicles already in the intersection: Vehicles preparing to enter a roundabout must yield to vehicles already in the intersection. Activate turn signals when turning: When turning left, stay close to the left side of the intersection center point. Activate turn signals when turning, and use low beams when driving at night. Proceed in order: When the signal permits, proceed in order. Stop behind the stop line when encountering a stop signal: When encountering a stop signal, stop in order behind the stop line. If there is no stop line, stop outside the intersection. Wait in order when awaiting signal permission: When turning right and encountering a vehicle in the same lane waiting for the signal, wait in order. Straight-going vehicles and pedestrians have the right of way: At intersections without directional signal lights, turning motor vehicles must yield to straight-going vehicles and pedestrians. Right-turning vehicles from the opposite direction must yield to left-turning vehicles. Some situations require special attention: Some intersections have dedicated left-turn traffic signals. Vehicles in the left-turn lane cannot turn left just because the straight-going signal is green; they must first move into the left-turn waiting lane and proceed only when the left-turn signal turns green. When approaching a curve on a steep slope: Reduce speed and sound the horn while proceeding slowly. Shift to a lower gear in advance to ensure sufficient climbing power and avoid shifting gears during the turn to prevent accidents. Choose the right timing for turning, aiming for a single smooth turn to avoid the need for reversing and increasing danger. In heavy fog or sandstorms: When driving and turning in such conditions, be fully aware of your surroundings. Turn on the front small lights and fog lights early, honk frequently to alert pedestrians and other vehicles, proceed slowly, and be prepared to brake and stop at any time. Turning on wet, snowy, or muddy roads: Use engine braking in advance to reduce speed and proceed slowly, avoiding sharp turns and sudden braking. When turning uphill, if other vehicles are stuck due to slipping and blocking the curve, park on the right side in advance and proceed only after the vehicles ahead have passed. When turning downhill and slipping, take care to prevent the vehicle from sliding and causing a collision. Turning at intersections: When turning left, drivers should signal early and stay as close to the center of the road as possible to facilitate vehicles behind and those turning right. When turning right, signal first, turn slowly, and be mindful of the inner wheel difference to prevent the right rear wheel from going off the road and hitting pedestrians or obstacles.
18
3
Share

What is the normal tire pressure for a Lexus ES?

The recommended tire pressure range for the Lexus ES200 is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be increased by 0.2 bar in winter and decreased by 0.1 bar in summer. This data is based on the international GBT2978-2008 standard. To check the current tire pressure of your Lexus ES200 during daily driving, you can activate the tire pressure monitoring system, and the tire pressure values will be displayed on the central LCD screen of the instrument panel. The specific method is to press the 'i' button and scroll up or down to access the menu where this information can be found. Generally, a tire pressure above 2.8 bar is considered too high, and a tire pressure below 2.0 bar is considered too low. Hazards of overinflated tires: Reduced friction and adhesion, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread pattern, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overstretches tire cords, reducing elasticity and increasing the load on the vehicle during driving. Hazards of underinflated tires: Increased friction coefficient with the road surface, leading to higher fuel consumption; causes heavy steering and deviation, compromising driving safety; increases movement of tire components, leading to abnormal heat generation from excessive rolling; reduces the functionality of cords and rubber, causing delamination or cord breakage and excessive friction with the rim, damaging the tire bead area and causing abnormal wear; multiplies friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to a tire blowout. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no seal on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Usually, the system will alert if the pressure is below 1.8 bar or above 3.0 bar. In this case, a tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure monitoring system is not reset in time, it will continue to display the previous data, causing the indicator light to stay on. Simply reset the tire pressure monitoring system to resolve this. Damaged tire pressure sensor: The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged during driving, it will trigger the tire pressure warning light. If the sensor is damaged, it must be replaced with a new one.
5
3
Share

Does the Audi Q5 come with a built-in dash cam?

Audi Q5 does not come with a built-in dash cam. Here are the selection methods for dash cams: 1. Lens: Glass lenses are better than resin lenses. 2. Chip: The main chip for dash cams is the Ambarella A7 series. 3. Sensor chip: Sensor chip parameters are often exaggerated. The mainstream sensor chips currently are ov4689 and ar0330ov4689, generally used in higher-end products, usually paired with A70 for the best top-tier configuration. 4. A 32G memory card is most suitable. Below is extended information about Audi cars: 1. Models under the brand: Audi A3, Audi A5, Audi A6L, Audi Q3, Audi S4, etc. 2. Introduction to Audi A6L: The front suspension is a five-link independent suspension, and the rear suspension is also a five-link independent suspension. It is equipped with a 2.0T turbocharged engine, with a maximum horsepower of 190PS, a maximum power of 140kW, a maximum torque of 320Nm, and is paired with a 7-speed dual-clutch transmission.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.