How to Tune the Radio in a Lexus ES?

1 Answers
McAlexis
07/29/25 7:15pm
To tune the radio in a Lexus ES, you can use the knob on the right side of the radio assembly, located at the lower right of the CD slot. To store a radio station, use the control panel on the center console, which is situated below the left side of the gear shift. The method is to select the desired station position and hold the control handle for 3 seconds until the station is successfully stored. Below are solutions for poor car radio signal: 1. First, replace the radio tuner. For original car navigation radios, prolonged use may lead to poor signal and performance. In such cases, adding another signal amplifier may not be very effective, so it is recommended to check the antenna first and then replace the radio tuner if the antenna is fine. 2. Secondly, install an external antenna or signal amplifier. Alternatively, you can install a signal amplifier, as the original navigation system usually comes with one built-in.
Was this review help?
8
3
Share
More Forum Discussions

How to Start on a Slope in Subject 2?

After stopping on the slope, keep the foot brake pressed, depress the clutch, and pull the handbrake tightly. Ensure the handbrake can hold the vehicle on the slope before releasing the foot brake. Once the vehicle is stationary on the slope, lift the clutch until the car body starts to shake, then release the brake without pressing the accelerator. Fine-tune the clutch to make the vehicle move forward or backward. Press the brake firmly with your heel and the accelerator with your toes. While revving the engine, slowly release the clutch with your left foot, lift your right heel off the brake, continue to accelerate while releasing the clutch to complete the slope start.
7
2
Share

How to Pass the S-Curve in Subject 2 with a Pickup Truck?

Maintain first gear throughout the entire process and avoid steering too abruptly. Keep the right wheel close to the right curb, and vice versa. Reduce speed when entering the curve to allow more reaction time for better navigation. Pay attention to the position of the front of the vehicle, keeping the outer front wheel as close as possible to the right edge of the curve. Use first gear with half-clutch to move forward, and do not stop during the process.
4
5
Share

How to Schedule the Subject 2 Driving Test?

Access the Ministry of Public Security's Comprehensive Traffic Safety Management Service Platform and select your province. Choose the test scheduling option. After entering your personal information, select the driver's license services. Choose between local or out-of-town test scheduling based on your situation. Verify your information. Read the precautions. Select the test location. After confirming the test time, click next to complete the registration.
19
4
Share

How to Operate on Downhill in Subject 2?

Lightly press the brake to let the car slowly move down the slope. Engage the appropriate gear, usually the 1st gear in Subject 2. Control the speed by gently pressing the brake; avoid sudden braking to prevent stalling. Release the clutch, and when reaching the bottom of the slope, press it to the half-engagement point while releasing the brake, then drive the car to the finish line.
12
3
Share

What are the correct steps for starting with the handbrake in Subject 2?

Hold the steering wheel with your left hand, adjust the seat to a comfortable position with your right hand, fasten the seat belt, and close the door. Release the handbrake, shift to neutral, and pay attention to the direction of your hands. Press the clutch pedal all the way down with your left foot, shift into first gear, and simultaneously press the brake pedal with your right foot. Turn on the left turn signal, honk the horn, and slowly lift your left foot to release the clutch. Once the car starts moving forward, the right foot should completely release the brake pedal, while the left foot remains at the semi-engaged clutch position, indicating a successful start. Align the front of the car with the yellow line of the left lane, maintain this alignment to drive straight.
20
5
Share

How to Solve the Oil Leakage Issue in a Cruze Engine?

Oil pan gasket damage or loose screws causing oil leakage; replace the gasket. Oil drain plug gasket damage, missing, or loose causing oil leakage; replace the gasket. Timing gear cover gasket improperly installed, damaged, or loose screws causing oil leakage; replace the gasket. Engine mounting plate deformation; replace the gasket or go to a repair shop to fix the mounting plate.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.