How to Tightly Close the Hood of a Sylphy?

1 Answers
LeEmery
07/30/25 3:47am
Sylphy's hood can be tightly closed by: lifting the hood to an angle roughly equivalent to placing a bottle of mineral water upright, then simply releasing your hand. The hood is made of rubber foam cotton and aluminum foil materials, which not only reduce engine noise but also isolate the heat generated during engine operation, effectively protecting the paint on the hood surface and preventing aging. The Sylphy is a compact car launched by Dongfeng Nissan, featuring a MacPherson independent front suspension and a torsion beam non-independent rear suspension. It is equipped with a 1.6L naturally aspirated engine, delivering maximum power outputs of 90kw and 99kw, paired with a CVT continuously variable transmission or a 5-speed manual transmission.
Was this review help?
15
0
Share
More Forum Discussions

What to Do When the Central Locking System Keeps Making Abnormal Noises?

Central locking system continuously making abnormal noises may indicate a malfunction. Here are the solutions: 1. Lock Body Issue: Go to an auto repair shop to replace the lock body. 2. Anti-Theft Device Issue: You can adjust the sensitivity of the anti-theft device on its control box. Generally, the control box is installed under the dashboard. After opening it, you will see a screw knob that can be rotated to adjust the sensitivity. It is recommended to reduce the sensitivity to a level where kicking the tire does not trigger the alarm. 3. Motor Issue: An aged motor needs replacement. 4. Fuse Issue: A blown fuse in the switch circuit needs replacement. 5. Central Locking System Host Issue: A faulty central locking system host needs replacement. 6. Main Motor Linkage Rod Issue: A loose main motor linkage rod needs tightening.
1
3
Share

What to Do If a Small Piece Is Scratched Off the Side of the Tire?

Tire sidewall scratched off a small piece needs to check whether the gap has been damaged or affected the tire material. If the sidewall is already damaged, it should be replaced in time; but if the gap has not affected the car tire material, it can continue to be used. Precautions to note when a small piece is scratched off the side of the tire: 1. If you find that a small piece is scratched off the side of the car tire, you should carefully inspect it. 2. Tire wear may interfere with the driver's normal driving and even put them in a potentially hazardous situation. 3. Tires are often used under complex and harsh conditions, bearing various deformations, loads, forces, and high and low-temperature effects during driving, so they must have high load-bearing performance, traction performance, and cushioning performance. 4. Drivers should pay great attention to the protection of car tires during driving and deal with tire failures in a timely manner.
20
2
Share

Is It Normal for Car LED Lights to Get Very Hot When in Use?

If the temperature exceeds 60 degrees Celsius, it is abnormal and indicates a heat dissipation issue. Below this temperature, it is considered normal. Introduction to the Heating Principle of Car LED Lights: Car LED lights use light-emitting diodes as the light source. During operation, only 25% of the electrical energy is converted into light energy, while the remaining electrical energy is entirely transformed into heat energy. When accumulated in an enclosed space, the heat builds up, causing the LED lights to become increasingly hot. Therefore, car LED lights must be used in conjunction with heat dissipation devices. Causes and Solutions for Overheating of Car LED Lights: If an infrared thermometer detects that the temperature of the headlight cover exceeds 60 degrees, it indicates that the LED lights are overheating due to poor heat dissipation in the lighting system. This issue can be resolved by spraying nano-radiation coating on the surface of the light body to enhance its heat radiation capability or by installing additional fans.
9
2
Share

What is the abbreviation for Ordos license plates?

Ordos license plates are abbreviated as Meng K. The license plate codes for various regions in Inner Mongolia are as follows: Meng A for Hohhot, Meng B for Baotou, Meng C for Wuhai, Meng D for Chifeng, Meng E for Hulunbuir, Meng F for Xing'an League, Meng G for Tongliao, Meng H for Xilin Gol League, Meng J for Ulanqab, Meng K for Ordos, Meng L for Bayannur, and Meng M for Alxa League. Relevant information is as follows: 1. License plates, commonly known as vehicle plates, refer to the plates hung on the front and rear of a vehicle. They are typically made of aluminum, sheet iron, plastic, or paper, and display the vehicle's registration number, registration region, or other relevant information. 2. License plates are hard number plates issued by the vehicle management authority after reviewing, inspecting, and registering a vehicle that has applied for a plate, bearing the registration code.
4
1
Share

What are the symptoms of over-tightening spark plugs?

Symptoms of over-tightening spark plugs include gas leakage, so we must avoid excessive tightening when replacing spark plugs. Location of spark plugs: Spark plugs are installed on the side or top of the engine. Early spark plugs were connected to the distributor via ignition cables, but in the past decade, most car engines have adopted direct connection between ignition coils and spark plugs. Spark plug replacement procedure: Open the hood and remove the engine's plastic cover. Disconnect the high-voltage distributor wires, marking each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs in sequence. During removal, check for external debris like leaves or dust and ensure thorough cleaning. Insert new spark plugs into the holes, hand-tightening them for several turns before using the socket wrench. Reinstall the high-voltage distributor wires according to the firing order, then secure the cover plate.
18
3
Share

Is a tire pressure of 3.0 normal for an SUV?

An SUV tire pressure of 3.0 bar is not normal. According to the international GBT2978-2008 standard, the recommended tire pressure for standard tires is 2.4-2.5 bar. A pressure of 3.0 bar exceeds the maximum recommended value, making it abnormal. Hazards of excessive tire pressure: Reduced tire friction and adhesion, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates wear on the central tread pattern, shortening tire lifespan; Increases vehicle vibration, indirectly affecting the lifespan of other components; Overextends tire cords, reducing elasticity and increasing the load on the vehicle during driving; Decreases puncture resistance. When encountering sharp objects like nails or glass on the road, the tire is more prone to punctures, leading to internal cracks or blowouts.
1
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.