How to Switch Between Recirculation and Fresh Air Mode in Audi A5?

1 Answers
McPaige
07/25/25 5:38am
Locate the air conditioning control area inside the vehicle, which is positioned below the center of the dashboard. The upper and lower buttons on the right side are for adjusting the recirculation/fresh air mode and turning off the air conditioning. The fresh air mode button is located below the dashboard, and the middle button controls the recirculation/fresh air mode. When the button is pressed and the indicator light turns on, it indicates the recirculation mode is activated. Pressing the button again to turn off the indicator light means the fresh air mode is activated. As long as the recirculation mode is not turned on, the fresh air mode remains active. Normally, the fresh air mode is used by default.
Was this review help?
6
1
Share
More Forum Discussions

What does the steering wheel warning light on the Wuling Hongguang S dashboard mean?

Wuling Hongguang S dashboard showing the steering wheel warning light indicates a fault in the power steering system. A malfunction in the power steering system can cause symptoms such as heavy steering, steering noise, steering wheel vibration, and poor steering wheel return ability. The Wuling Hongguang S is a microvan with body dimensions of 4390mm in length, 1660mm in width, and 1750mm in height, with a wheelbase of 2720mm. It is equipped with a 1.2L engine and a 5-speed manual transmission, delivering a maximum power of 56 kW and a maximum torque of 110 Nm. The drive system is front-engine, rear-wheel drive, with a front suspension using MacPherson strut independent suspension and a rear suspension using leaf spring non-independent suspension.
7
4
Share

What to do if the car engine is knocking?

When the knocking is slight, the engine power is slightly unstable, the engine shakes severely, and it will cause the engine to overheat and emit black smoke. The solutions for car engine knocking are as follows: 1. After the engine starts, if there is a knocking sound during low-temperature operation, and the sound disappears when the temperature returns to normal, it can be left untreated temporarily and continue to run. 2. When the engine temperature is normal, if there is an obvious knocking sound, high-speed operation should be avoided as much as possible, and the engine should be disassembled and repaired as soon as possible. 3. If the cylinder is severely out-of-round, scratched, or the gap between the piston and the cylinder is too large, it should be replaced. 4. If the connecting rod is found to be deformed, it should be replaced as much as possible.
17
3
Share

How Long Does a Subaru Boxer Engine Last?

Subaru boxer engines generally last between 200,000 to 300,000 kilometers. More information about Subaru boxer engines is as follows: 1. The Subaru boxer engine can enhance performance on paved roads and also improve driving capability in adverse road conditions. When controlling drive on stable road surfaces, the flexible utilization of the motor's powerful torque and responsive sensitivity further enhances passability in challenging road conditions. 2. In vehicle configurations equipped with this engine, the addition of a rear support auxiliary frame increases the torsional rigidity of the wheels and the rigidity of the rear suspension auxiliary frame mounting points. This achieves performance equivalent to gasoline vehicles in all aspects, including handling stability, vibration and noise performance, and ride comfort.
12
1
Share

When Should Fuel Additives Be Added?

Fuel additives are generally added every 10,000 kilometers. Here is the relevant introduction: 1. Engine carbon deposits can gradually accumulate inside the engine unnoticed. If carbon deposits are ignored, they can slowly reduce engine power, lower fuel efficiency, worsen emissions, and lead to a series of engine malfunctions. 2. The fuel system can remove carbon deposits, enhance power, save fuel, reduce noise, and prevent engine failures caused by fuel issues. 3. Automotive maintenance chemicals clean the fuel system, stabilize fuel, reduce carbon deposits, and protect the engine. However, the current market for fuel additives is mixed with varying quality. Under normal circumstances, it is recommended to use OEM (Original Equipment Manufacturer) additives, typically adding them once every 10,000 kilometers is sufficient.
11
4
Share

How to set the horn sound when locking the Avalon?

The Avalon cannot manually set the horn sound when locking. More information about the Avalon is as follows: 1. The Avalon is a mid-size sedan equipped with a 2.5L naturally aspirated engine, delivering a maximum horsepower of 209ps and maximum torque of 250N·m. 2. The Avalon measures 4975mm in length, 1850mm in width, and 1450mm in height, with a wheelbase of 2870mm. 3. The Avalon features a 4-door, 5-seat sedan body style, paired with an 8-speed automatic transmission, front-wheel drive layout, and power steering system.
12
0
Share

Does a new car need polishing before crystal coating?

New cars do not require polishing before crystal coating. If the car has just been delivered and hasn't undergone long-distance transportation or prolonged storage, the paint surface remains smooth without an oxidation layer, allowing direct application of crystal coating. However, if the car has been transported over long distances or stored for an extended period, resulting in a noticeable oxidation layer on the paint surface, light polishing is necessary to remove it. This ensures the crystal coating adheres fully to the paint, forming an effective protective layer. Under normal circumstances, new cars do not require polishing before crystal coating. More details are as follows: 1. Crystal coating is essentially an upgraded version of car waxing, enhancing the brightness and hardness of the paint to protect it. 2. After crystal coating, owners will notice a more transparent and brighter paint finish, increased resistance to scratches, and improved corrosion resistance.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.