How to Stop the Mercedes Wiper in the Middle?

What are the causes of the whole vehicle insulation failure in the BAIC EU5 R500?

Here are the reasons for the whole vehicle insulation failure in the BAIC EU5 R500: 1. Battery electrolyte leakage: The electrolyte is dilute sulfuric acid, which can corrode the vehicle body and other equipment. After the single-cell liquid is completely leaked, the electrode plates are directly exposed to air, causing oxidation of the plates and shortening the battery's service life. 2. External liquid ingress: After the battery system is submerged, gas is generated due to the electrolysis of water reaction. The movement of high-pressure connected gas produces switching, causing arcing at the connection points. If fully submerged, the arcing may cause a battery fire. 3. Formation of conductive circuits: After the insulation layer is damaged, conductive circuits appear between battery modules and cells, causing short circuits and resulting in whole vehicle insulation failure.

19

1

Share

Why is the fuel consumption of the BMW X4 so high?

BMW X4 has high fuel consumption due to excessive carbon deposits and poor cylinder sealing. Here is an introduction to fuel consumption-related content: 1. Fuel consumption: The fuel consumption of large-displacement cars is as high as that of family cars. 2. Comparison: The fuel consumption per 100 kilometers is 6 liters. On the same route, a 1.6L car like the Octavia consumes 7 liters. Sports cars usually require much more throttle input than street cars, resulting in higher fuel consumption. For example, a liter-class sports car during aggressive acceleration or high-speed driving can have fuel consumption comparable to a 3.0L car's combined fuel consumption. 3. Fuel: Most cars use gasoline, so the energy content of the fuel is the same. The relatively higher fuel consumption of the Octavia comes from high wind resistance, a compact structure that leaves no room for fuel-saving technologies, and a high-revving design philosophy to extract maximum power.

5

0

Share

Is the BMW's external circulation A or M?

BMW's external circulation is A, while M is the forced internal circulation. Below is an introduction to the related content of internal and external circulation: 1. Internal circulation: When using internal circulation, the vehicle's interior space is like a sealed environment. Whether it's the cold or hot air blown out by the air conditioning, it circulates within the car, and no fresh air enters the vehicle. 2. External circulation: When external circulation is turned on, fresh external air flows into the car, improving the air quality inside the vehicle, which is also a good way to use it. Below are extended details on whether to use internal or external circulation during normal driving: 1. Summer: Turn on the internal circulation when using the air conditioning in summer to prevent outside heat from entering the car, during smoggy days, or when stuck in traffic to avoid outside air from entering the vehicle. 2. Highway: Use external circulation when driving on the highway to ensure fresh air circulation, when smoking to quickly expel smoke, or after the car has been exposed to the sun to release toxic gases from the interior.

1

0

Share

What is the difference between 0w30 and 0w40?

Here are the differences between 0w30 and 0w40: 1. The smaller the number before the W in the oil grade, the lower the low-temperature viscosity. The larger the number after the W, the higher the viscosity. Generally, oils used in winter will have the letter W, which stands for Winter; 2. The smaller the number before the W, the lower the low-temperature viscosity, the better the low-temperature fluidity, and the lower the applicable minimum temperature. For example, 0W has better low-temperature fluidity than 5W. If there is a number after the W, such as 30 or 40, it represents the viscosity of the oil at 100°C; 3. Due to the difference in viscosity, the two oils are suitable for different types of engines. In terms of low-temperature fluidity, these two oils are similar, but 0w40 oil has higher viscosity than 0w30, so in terms of engine usage, 0w40 is more suitable for turbocharged engines, while 0w30 performs better in naturally aspirated engines.

9

0

Share

What is the maximum wading depth of the Ford Edge?

The maximum wading depth of the Ford Edge is 550mm. The wading depth of the Ford Edge is determined by the height of the vehicle's chassis, which is the ground clearance listed in the vehicle's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when driving through waterlogged roads. If the air intake of the Ford Edge is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. Alternatively, the height of the engine's air intake (and thus the maximum wading depth) can be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before driving through water, always turn off the auto start-stop function to prevent the vehicle from automatically restarting after stalling in the water, which could cause severe engine damage due to water ingress. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use reference points such as warning water level markers, trees, or the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed. Instead, choose an alternative route.

4

3

Share

Why is the air conditioning in the Baojun E200 not cooling?

Here are the reasons why the air conditioning in the Baojun E200 is not cooling: 1. Internal damage: Severe internal wear of the compressor leads to its inability to function properly. 2. Oil stains: The presence of oil stains at the connections or seams indicates refrigerant leakage, requiring reinforcement or replacement of the relevant parts. 3. Circuit system failure: It is also very common for the car's air conditioning compressor to malfunction due to circuit system failures. You can check if the circuit is functioning properly, inspect the temperature sensor solenoid valve, and other potential causes of failure. Below is additional information about the Baojun 730: 1. Body dimensions: A 5-door, 7-seater MPV under SAIC-GM-Wuling, with length, width, and height of 4780mm, 1780mm, and 1740mm respectively, and a wheelbase of 2750mm. 2. Transmission: Equipped with a 6-speed manual transmission, achieving a top speed of 150 km/h.

4

1

Share

How to Stop the Mercedes Wiper in the Middle?

What are the causes of the whole vehicle insulation failure in the BAIC EU5 R500?

Why is the fuel consumption of the BMW X4 so high?

Is the BMW's external circulation A or M?

What is the difference between 0w30 and 0w40?

What is the maximum wading depth of the Ford Edge?

Why is the air conditioning in the Baojun E200 not cooling?

Is it okay to engage P gear without pulling the handbrake?

How to Check the Production Date of New Car Tires?

Which Porsche Model Features Five Dashboard Gauges?

What are the reasons for unstable steering wheel in trucks?