···
Log in / Register

How to Steer When the Rear Wheels Skid?

3 Answers
McGraham
07/29/25 3:30pm
You should turn the steering wheel in the opposite direction of the skid. Then, turn the steering wheel in the same direction as the skid. Try to avoid stopping on slippery roads. If the wheels skid during startup, clear away mud or snow.
Was this review help?
20
0
Share
StBradley
08/14/25 9:04am
I remember an experience of skidding in a rear-wheel-drive car after rain. When handling it, you should gently steer the wheel in the opposite direction of the skid. For example, if the rear wheels slide to the left, turn the steering wheel slightly to the right, but not too abruptly to avoid spinning out of control. That time, I stabilized the car and gently eased off the throttle and brakes, and the traction returned. After that, I slowed down and pulled over to check. Skidding often occurs due to wet roads or sudden acceleration. Maintaining a steady speed while driving can help prevent it, especially for rear-wheel-drive cars in curves—extra caution is needed. Regularly checking tire pressure and wear is also important to ensure good traction. If you frequently drive on rough outdoor roads, it’s better to carry some emergency tools.
Was this review help?
18
0
Share
Expand All
StKathryn
10/12/25 2:14am
When I first started driving, I encountered this situation and was initially panicked, but now I've learned better: gently steer the wheel in the opposite direction of the skid. If the skid is to the left, slightly turn the wheel to the right without rushing, otherwise the car may fishtail. Keep the throttle steady and avoid sudden acceleration; wait for the wheels to straighten before slowly driving away. As a beginner, practicing this technique in an empty parking lot was quite effective—remember, safety first! Skidding is often caused by sudden acceleration or slippery conditions, so pay attention to road signs, slow down, and avoid puddles. Always check the braking system before each trip to prevent malfunctions that could lead to greater risks.
Was this review help?
18
2
Share
Expand All
More Forum Discussions

How to Deal with the Continuously Illuminated Tire Pressure Monitoring Light on Lavida?

Turn on the ignition switch, press and hold the SET button of the tire inflation pressure control system until the dashboard indicator light comes on. Wait for the system to confirm the storage of new parameters, and the tire pressure monitoring light will automatically turn off, completing the reset. Below are the specific methods to eliminate the tire pressure monitoring light: 1. First, turn off the engine, then turn on the power for vehicle self-inspection. Press and hold the tire pressure monitoring button on the right front side of the gear shift lever for about three seconds until you hear a "ding" sound. Release the button to eliminate the tire pressure warning light on the dashboard. 2. If the light cannot be eliminated, visit a Volkswagen after-sales service center. Have the staff check the tire pressure and related systems such as sensors. After confirming there are no faults, use a specialized decoder to clear the tire pressure warning light on the vehicle.
18
2
Share

What does the engine fault light EDC mean?

EDC fault light indicates that there is a problem with the engine electronic control system, reminding the owner to go to the repair shop for inspection and maintenance as soon as possible. Here is some information about EDC: 1. The full name of EDC is Electric-Diesel-Control, which means electronic control system for diesel injection; its task is to electronically control the fuel injection system to achieve real-time control of fuel injection quantity and timing according to operating conditions. 2. When EDC appears on the car dashboard, it indicates an engine fault. When the EDC fault light comes on, it means there is a problem with the engine.
7
0
Share

What is the principle of car tire pressure monitoring?

Car tire pressure monitoring principle depends on the type of monitoring device, specifically introduced as follows: 1. Direct tire pressure monitoring: Uses pressure sensors installed inside the tires to measure air pressure, and wireless transmitters to send pressure information from inside the tire to a central receiver module. 2. Indirect tire pressure monitoring: When tire pressure decreases, the vehicle's weight causes that wheel's rolling radius to become smaller. By comparing rotational speed differences between tires, it achieves the purpose of monitoring tire pressure. 3. Functions of tire pressure monitoring: Prevent accidents; Extend tire service life.
9
1
Share

What to Do When the Car Key Won't Come Out?

When a car key won't come out, it's not necessarily a malfunction. There are two common scenarios: first, the key won't come out after turning off the engine; second, the key can't be turned after insertion. Here are the details: 1. Key won't come out after turning off the engine (common in automatic transmission models): In this case, the owner should check if there's any obstruction in the gear slot. Remove the obstruction, start the car, shift the gear again to ensure it's fully back in place, and then the key can be pulled out. 2. Key can't be turned after insertion: This is actually the car's automatic steering wheel lock function, a simple anti-theft feature. To resolve this, turn the key forcefully with your right hand while gently shaking the steering wheel left and right with your left hand, and the key will turn.
1
3
Share

What are the effects of overfilling engine oil?

The effects of overfilling engine oil are: 1. Intense agitation between engine components, leading to excessive engine load and power loss; 2. Oil splashing onto cylinder walls and entering the intake system through the crankcase ventilation system, causing oil burning issues. The method for changing engine oil is: 1. Lift the vehicle with a jack, locate and loosen the drain plug to drain the oil; 2. Remove the oil filter and place a container beneath it; 3. Install a new oil filter and add fresh oil. The functions of engine oil are: 1. Reduce friction and high temperatures; 2. Cool down the engine; 3. Clean and remove contaminants; 4. Dampen vibrations; 5. Prevent rust and corrosion.
2
3
Share

How to Replace the Spark Plugs of Chery Tiggo 3?

Chery Tiggo 3's spark plug replacement method is as follows: 1. Clean the dust around the engine cylinder wires to prevent dust from entering the engine during replacement; 2. Use a wrench to loosen the spark plugs in the engine, remove the old spark plugs, then install the new spark plugs and screw them back in. The Chery Tiggo 3 is a compact SUV with the following dimensions: length 4420mm, width 1760mm, height 1670mm, wheelbase 2510mm, fuel tank capacity 55 liters, and trunk capacity 550 liters. The Chery Tiggo 3 is equipped with a 1.5L naturally aspirated engine with a maximum horsepower of 116.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.